Qingsuo Liu

High-strength steels are widely used in various mechanical production and construction industries for their low cost, high strength and high toughness. Among these, bainitic steels have better comprehensive performance relative to martensite and ferrite. In this paper, from the point of view of its microscopic fine structure and mechanical properties, the high-carbon silicon-containing steel Fe-0.99C-1.37Si-0.44Mn-1.04Cr-0.03Ni was austenitized at high temperature after a brief isothermal treatment at 280 °C and is briefly reviewed. We have used EBSD, TEM and 3D-APT to observe a unique transformation in which high-carbon silicon-containing steels form nanostructured bainite with nanometer widths. Intriguingly, as the isothermal duration decreases, the beam bainite width becomes increasingly finer. When the beam bainite width falls below 50 nm, there is a sudden shift in defect type from the conventional edge-type dislocations to a defect characterized by the insertion of a semi-atomic surface in the opposite direction, which leads to different degrees of reduction in the micro- and macro-mechanical properties of high-carbon silicon-containing steels from 1754 MPa to 1667 MPa. This sudden change in the sub-structural properties is typical of the reverse Hall–Petch effect.

The effects of rare earth element Sm on the microstructure, mechanical properties, and shape memory effect of the high temperature shape memory alloy, Cu-13.0Al-4.0Ni-xSm (x = 0, 0.2 and 0.5) (wt.%), are studied in this work. The results show that the Sm addition reduces the grain size of the Cu-13.0Al-4.0Ni alloy from millimeters to hundreds of microns. The microstructure of the Cu-13.0Al-4.0Ni-xSm alloys are composed of 18R and a face-centered cubic Sm-rich phase at room temperature. In addition, because the addition of the Sm element enhances the fine-grain strengthening effect, the mechanical properties and the shape memory effect of the Cu-13.0Al-4.0Ni alloy were greatly improved. When x = 0.5, the compressive fracture stress and the compressive fracture strain increased from 580 MPa, 10.5% to 1021 MPa, 14.8%, respectively. When the pre-strain is 10%, a reversible strain of 6.3% can be obtained for the Cu-13.0Al-4.0Ni-0.2Sm alloy.

The formation of nanocrystalline structures in bulk metal materials is of great significance for both investigating the structural features of nanocrystalline materials and enhancing the value of bulk metal materials in engineering applications. Herein, we report a nanocrystalline structure formed by lattice transformation in a three-dimensional bulk metal material. We characterized its phase composition, three-dimensional features, and boundary structure. This nanocrystalline structure had microscale length and height and nanoscale width, which gave it a “nanoplate” structure in three-dimensional space. We observed edge dislocations in the interior of the nanocrystalline structure. A unique transitional boundary that contributed to maintaining its nanoscale size was found at the border between the parent phase and the nanocrystalline structure.

The influence of hafnium element's incorporation on a Cu– xHf–13.0Al–4.0Ni (wt-%) ( x = 0.5, 1.0 and 2.0) high-temperature shape memory alloy was investigated systematically. The results show that the matrix of Cu– xHf–13.0Al–4.0Ni ( x = 0.5, 1.0 and 2.0) alloys is 18R martensite, and an orthorhombic-structured Cu₈Hf₃ phase is formed and distributed at the grain boundaries. The grain size is significantly reduced with increasing Hf content. The mechanical properties of Cu– xHf–13.0Al–4.0Ni ( x = 0.5, 1.0 and 2.0) alloys are improved by Hf doping due to the combination of refinement strengthening, solid solution strengthening and second phase strengthening. After heating under pre-strain of 10%, the shape memory effect of the Cu–1.0Hf–13.0Al–4.0Ni alloy reaches 5.6%, which is obviously higher than that of the Cu–13.0Al–4.0Ni alloy.

The XRD analysis, microstructure observation and mechanical test were used to investigate the phase composition, micromorphology and mechanical properties of the intermediate transformation products in an ultra-low carbon steel non-containing Nb and Ti elements. The results showed that even without the presence of Nb and Ti alloy compounds, the experimental steel still exhibited good Rockwell hardness level. When the steels were held for a shorter times at 450°C, its Rockwell hardness under stayed 100s after plastic deformation at 850°C was higher than that under cooled directly because the 100s-stayed process was benefit to the formation of nanobainite. However, when the steels were held over 30min at 450°C, its Rockwell hardness under stayed 100s were close to that of non-stayed steel.