Petr Vopěnka
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Petr Vopěnka has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Arko Lucieer
School of Geography, Planning and Spatial Sciences, University of Tasmania, Private Bag 78, Hobart, TAS 7001, Australia
1 shared publication - Darren Turner
BSchool of Geography, Planning, and Spatial Sciences, University of Tasmania, Hobart, TAS 7005, Australia
1 shared publication - Jan Kašpar
Faculty of Forestry and Wood Sciences, Czech University of Life Sciences Prague, Kamýcká 129, Praha 6 Suchdol 165 21, Czech Republic
1 shared publication - Luke Wallace
School of Geography, Planning and Spatial Sciences, University of Tasmania, Hobart, TAS 7005, Australia
1 shared publication - Róbert Marušák
Faculty of Forestry and Wood Sciences, Czech University of Life Sciences Prague, Kamýcká 129, Praha 6 Suchdol 165 21, Czech Republic
1 shared publication - Zbyněk Malenovský
Remote Sensing Research Group, Department of Geography University of Bonn Bonn Germany
1 shared publication
Latest Publications
- Top Cited PapersOpen Access
Assessment of Forest Structure Using Two UAV Techniques: A Comparison of Airborne Laser Scanning and Structure from Motion (SfM) Point Clouds
This study investigates the potential of unmanned aerial vehicles (UAVs) to measure and monitor structural properties of forests. Two remote sensing techniques, airborne laser scanning (ALS) and structure from motion (SfM) were tested to capture three-dimensional structural information from a small multi-rotor UAV platform. A case study is presented through the analysis of data collected from a 30 × 50 m plot in a dry sclerophyll eucalypt forest with a spatially varying canopy cover. The study provides an insight into the capabilities of both technologies for assessing absolute terrain height, the horizontal and vertical distribution of forest canopy elements, and information related to individual trees. Results indicate that both techniques are capable of providing information that can be used to describe the terrain surface and canopy properties in areas of relatively low canopy closure. However, the SfM photogrammetric technique underperformed ALS in capturing the terrain surface under increasingly denser canopy cover, resulting in point density of less than 1 ground point per m2 and mean difference from ALS terrain surface of 0.12 m. This shortcoming caused errors that were propagated into the estimation of canopy properties, including the individual tree height (root mean square error of 0.92 m for ALS and 1.30 m for SfM). Differences were also seen in the estimates of canopy cover derived from the SfM (50%) and ALS (63%) pointclouds. Although ALS is capable of providing more accurate estimates of the vertical structure of forests across the larger range of canopy densities found in this study, SfM was still found to be an adequate low-cost alternative for surveying of forest stands.
Top Cited PapersOpen AccessAssessment of Forest Structure Using Two UAV Techniques: A Comparison of Airborne Laser Scanning and Structure from Motion (SfM) Point Clouds
This study investigates the potential of unmanned aerial vehicles (UAVs) to measure and monitor structural properties of forests. Two remote sensing techniques, airborne laser scanning (ALS) and structure from motion (SfM) were tested to capture three-dimensional structural information from a small multi-rotor UAV platform. A case study is presented through the analysis of data collected from a 30 × 50 m plot in a dry sclerophyll eucalypt forest with a spatially varying canopy cover. The study provides an insight into the capabilities of both technologies for assessing absolute terrain height, the horizontal and vertical distribution of forest canopy elements, and information related to individual trees. Results indicate that both techniques are capable of providing information that can be used to describe the terrain surface and canopy properties in areas of relatively low canopy closure. However, the SfM photogrammetric technique underperformed ALS in capturing the terrain surface under increasingly denser canopy cover, resulting in point density of less than 1 ground point per m2 and mean difference from ALS terrain surface of 0.12 m. This shortcoming caused errors that were propagated into the estimation of canopy properties, including the individual tree height (root mean square error of 0.92 m for ALS and 1.30 m for SfM). Differences were also seen in the estimates of canopy cover derived from the SfM (50%) and ALS (63%) pointclouds. Although ALS is capable of providing more accurate estimates of the vertical structure of forests across the larger range of canopy densities found in this study, SfM was still found to be an adequate low-cost alternative for surveying of forest stands.
- Open Access
Decision Support Systems (DSS) Optimal—A Case Study from the Czech Republic
Forest managers have traditionally planned harvests using their expert knowledge. This applies mainly to the spatial distribution of harvest units. The amount of timber to be harvested is regulated by market demand. In addition to forest managers’ expert knowledge, there is a set of rules, which can be automatized. Computerized harvest planning will lead not only to saving time of forest managers, but it will also enable them to explore various scenarios in a matter of minutes. We introduce Optimal—GIS tool for spatial and temporal decisions of harvest scheduling. Optimal allows creating new harvest units, which reflects the forestry act and/or forest managers’ requirements. Optimal includes necessary tools for automatic controlling of harvest unit parameters. It allows alternative harvest scheduling, while taking into account different constraints. Optimal is a decision Support System designed and applied for clear-cut and shelterwood silvicultural systems with respect to the environmental and economic constraints.
Open AccessDecision Support Systems (DSS) Optimal—A Case Study from the Czech Republic
Forest managers have traditionally planned harvests using their expert knowledge. This applies mainly to the spatial distribution of harvest units. The amount of timber to be harvested is regulated by market demand. In addition to forest managers’ expert knowledge, there is a set of rules, which can be automatized. Computerized harvest planning will lead not only to saving time of forest managers, but it will also enable them to explore various scenarios in a matter of minutes. We introduce Optimal—GIS tool for spatial and temporal decisions of harvest scheduling. Optimal allows creating new harvest units, which reflects the forestry act and/or forest managers’ requirements. Optimal includes necessary tools for automatic controlling of harvest unit parameters. It allows alternative harvest scheduling, while taking into account different constraints. Optimal is a decision Support System designed and applied for clear-cut and shelterwood silvicultural systems with respect to the environmental and economic constraints.