Goran Mladenovic
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Goran Mladenovic has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
Ljubodrag Tanovic
University of Belgrade
2 shared publications- Aleksandar Maslarević
Faculty of Mechanical Engineering, Innovation Center, Belgrade
1 shared publication - Aleksandar Sedmak
University of Belgrade, Faculty of Mechanical Engineering, Belgrade, Serbia
1 shared publication - Biljana Marković
Faculty of Mechanical Engineering, University of East Sarajevo, Vuka Karadžića 30, East Sarajevo 71123, Republic of Srpska, Bosnia and Herzegovina
1 shared publication - Gordana Bakic
Faculty of Mechanical Engineering, University of Belgrade, 11000 Belgrade, Serbia
1 shared publication Kornel Ehmann
1 shared publication
Latest Publications
- Open Access
Determination of the Actual Stress–Strain Diagram for Undermatching Welded Joint Using DIC and FEM
This paper presents new methodology for determining the actual stress–strain diagram based on analytical equations, in combination with numerical and experimental data. The first step was to use the 3D digital image correlation (DIC) to estimate true stress–strain diagram by replacing common analytical expression for contraction with measured values. Next step was to estimate the stress concentration by using a new methodology, based on recently introduced analytical expressions and numerical verification by the finite element method (FEM), to obtain actual stress–strain diagrams, as named in this paper. The essence of new methodology is to introduce stress concentration factor into the procedure of actual stress evaluation. New methodology is then applied to determine actual stress–strain diagrams for two undermatched welded joints with different rectangular cross-section and groove shapes, made of martensitic steels X10 CrMoVNb 9-1 and Armox 500T. Results indicated that new methodology is a general one, since it is not dependent on welded joint material and geometry.
Open AccessDetermination of the Actual Stress–Strain Diagram for Undermatching Welded Joint Using DIC and FEM
This paper presents new methodology for determining the actual stress–strain diagram based on analytical equations, in combination with numerical and experimental data. The first step was to use the 3D digital image correlation (DIC) to estimate true stress–strain diagram by replacing common analytical expression for contraction with measured values. Next step was to estimate the stress concentration by using a new methodology, based on recently introduced analytical expressions and numerical verification by the finite element method (FEM), to obtain actual stress–strain diagrams, as named in this paper. The essence of new methodology is to introduce stress concentration factor into the procedure of actual stress evaluation. New methodology is then applied to determine actual stress–strain diagrams for two undermatched welded joints with different rectangular cross-section and groove shapes, made of martensitic steels X10 CrMoVNb 9-1 and Armox 500T. Results indicated that new methodology is a general one, since it is not dependent on welded joint material and geometry.
- 25 September 2019
- Published by Springer Nature
- p. 460-476
The Development of CAD/CAM System for Automatic Manufacturing Technology Design for Part with Free Form Surfaces
- 25 September 2019
- Published by Springer Nature
- p. 460-476
The Development of CAD/CAM System for Automatic Manufacturing Technology Design for Part with Free Form Surfaces
- 16 May 2017
- Published by ASME International in Journal of Engineering Materials and Technology
- Vol. 139 (4)
Experimental Examination of the Impact of Tool Radius on Specific Energy in Microcutting of Granite
The paper presents experimental results of microcutting brittle materials (granite). The analysis was conceived on the observed interaction between the workpiece and two tools of different shapes. Experiment was based on scratching the workpiece surface with diamond tools. Applied tools had tip radius R0.2 and R0.15 mm. The experiment determined the changes in the value of perpendicular and tangential components of the cutting force based on the geometric properties of tools, as well as the changes of the specific energy of microcutting granite (Jošanica and Bukovik types). The experiment has shown that reduction of tool radius causes reduction of the cutting force intensity and specific cutting energy. Because of its physical/mechanical properties, more energy is required for micromachining granite “Jošanica” than “Bukovik.” Based on the topography of the surface, the value of critical tool penetration depth was established, after which the brittle fracture is no longer present. For granite “Jošanica” values of critical penetration depth are 6 and 5 μm when micromachining with tools R0.2 and R0.15 mm, while for Bukovik those values are 6.5 and 5.5 μm. The paper should form the basis for understanding the phenomena which occur during microcutting brittle materials.
- 16 May 2017
- Published by ASME International in Journal of Engineering Materials and Technology
- Vol. 139 (4)
Experimental Examination of the Impact of Tool Radius on Specific Energy in Microcutting of Granite
The paper presents experimental results of microcutting brittle materials (granite). The analysis was conceived on the observed interaction between the workpiece and two tools of different shapes. Experiment was based on scratching the workpiece surface with diamond tools. Applied tools had tip radius R0.2 and R0.15 mm. The experiment determined the changes in the value of perpendicular and tangential components of the cutting force based on the geometric properties of tools, as well as the changes of the specific energy of microcutting granite (Jošanica and Bukovik types). The experiment has shown that reduction of tool radius causes reduction of the cutting force intensity and specific cutting energy. Because of its physical/mechanical properties, more energy is required for micromachining granite “Jošanica” than “Bukovik.” Based on the topography of the surface, the value of critical tool penetration depth was established, after which the brittle fracture is no longer present. For granite “Jošanica” values of critical penetration depth are 6 and 5 μm when micromachining with tools R0.2 and R0.15 mm, while for Bukovik those values are 6.5 and 5.5 μm. The paper should form the basis for understanding the phenomena which occur during microcutting brittle materials.
- 1 June 2015
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 137 (3) , 034502
Experimental Investigation of Microcutting Mechanisms in Oxide Ceramic CM332 Grinding
The paper contains an experimental study of microcutting intended to help the optimization of the grinding process of the oxide ceramic CM332 (99.5% Al2O3) grinding. The need for investigating the mechanisms occurring between the abrasive material and the ceramic is imposed by the fact that grinding is the dominant technology used to achieve the required quality of the workpiece surface finish. The microcutting process was performed with a single diamond cone-shaped grain of tip radius of 0.2 mm at varying depths of cut. The investigations were carried out to determine the normal and tangential cutting forces, the critical penetration depth and the specific grinding energy as a function of the grain penetration speed and depth. The critical grain penetration depth separating ductile flow from brittle fracture falls within the 4–6 μm range. The values of the critical penetration depth are also consistent with the results of changes in the cutting forces and the specific grinding energy. The chip formation mechanism is associated with the presence of median/radial and lateral cracks, ductile flow, chipping along the groove, and crushing beneath the diamond grain, all this affecting the quality of the ceramic's machined surface.
- 1 June 2015
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 137 (3) , 034502
Experimental Investigation of Microcutting Mechanisms in Oxide Ceramic CM332 Grinding
The paper contains an experimental study of microcutting intended to help the optimization of the grinding process of the oxide ceramic CM332 (99.5% Al2O3) grinding. The need for investigating the mechanisms occurring between the abrasive material and the ceramic is imposed by the fact that grinding is the dominant technology used to achieve the required quality of the workpiece surface finish. The microcutting process was performed with a single diamond cone-shaped grain of tip radius of 0.2 mm at varying depths of cut. The investigations were carried out to determine the normal and tangential cutting forces, the critical penetration depth and the specific grinding energy as a function of the grain penetration speed and depth. The critical grain penetration depth separating ductile flow from brittle fracture falls within the 4–6 μm range. The values of the critical penetration depth are also consistent with the results of changes in the cutting forces and the specific grinding energy. The chip formation mechanism is associated with the presence of median/radial and lateral cracks, ductile flow, chipping along the groove, and crushing beneath the diamond grain, all this affecting the quality of the ceramic's machined surface.
- 1 January 2015
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in FME Transactions
- Vol. 43 (1) , 9-15
Tool path generation for milling of free form surfaces with feed rate scheduling
The use of freeform (sculptured) surfaces in the product design process is accelerating at an exponential rate driven by functional as well as esthetics demands. CAD/CAM software is a must in their design and manufacture. While the geometric aspects of the design are relatively wellcovered, issues still remain when it comes to the actual manufacture of freeform surfaces. The major issues are related to the generation of the proper toolpaths that would assure the required surface quality, the minimization of the total maching time, the control of the magnitude of the cutting forces, etc. This paper presents an algotithmic procedure for tool path generation based on the criterion of maintaing the cutting forces at a constant pre-defined level for 3-axis ball end milling processes. To this end, a model for cutting force prediction is formulated and incorporated into the tolpath generation algorithm and software that is compatible with all CAD/CAM systems. It has been experimentally confirmed that the proposed algorithm offers a number advantages over the machining strategies used in commercial CAD/CAM software.
- 1 January 2015
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in FME Transactions
- Vol. 43 (1) , 9-15
Tool path generation for milling of free form surfaces with feed rate scheduling
The use of freeform (sculptured) surfaces in the product design process is accelerating at an exponential rate driven by functional as well as esthetics demands. CAD/CAM software is a must in their design and manufacture. While the geometric aspects of the design are relatively wellcovered, issues still remain when it comes to the actual manufacture of freeform surfaces. The major issues are related to the generation of the proper toolpaths that would assure the required surface quality, the minimization of the total maching time, the control of the magnitude of the cutting forces, etc. This paper presents an algotithmic procedure for tool path generation based on the criterion of maintaing the cutting forces at a constant pre-defined level for 3-axis ball end milling processes. To this end, a model for cutting force prediction is formulated and incorporated into the tolpath generation algorithm and software that is compatible with all CAD/CAM systems. It has been experimentally confirmed that the proposed algorithm offers a number advantages over the machining strategies used in commercial CAD/CAM software.