Yongkai Quan
Yongkai Quan has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
Bensi Dong
National Key Laboratory of Science and Technology on Aero-Engine Aero-Thermodynamics, Beihang University, Beijing 100191, China
3 shared publicationsGuoqiang Xu
National Key Laboratory of Science and Technology on Aero‐thermodynamics, School of Energy and Power EngineeringBeihang University Beijing 100191 China
2 shared publicationsGu Song
National Key Laboratory of Science and Technology on Aero-Engine Aero-thermodynamics, School of Energy and Power Engineering, Beihang University, Beijing 100191, China
1 shared publicationJianyu Liu
1 shared publication- Jiawei Fang
College of Urban Construction and Safety Engineering, Shanghai Institute of Technology, Shanghai 201418, China
1 shared publication Jichen Liu
1 shared publication
Latest Publications
- Open Access
- 26 April 2019
- Published by Art & Technology Publishing PTE. LTD. in Journal of Chemical Research and Application
- Vol. 2 (1)
Multistage auto-ignition of undiluted methane/air mixtures under engine-relevant condition
Gas-phase auto-ignition delay times (IDTs) of methane/“air” (21% O2/79% Ar) mixtures were measured behind reflected shock waves, using a kinetic shock tube. Experiments were performed at fixed pressure of 1.8 MPa and equivalence ratios of 0.5 and 1.0, over the temperature range of 800–1000 K. Overall, the effect of equivalence ratio on IDT is negligible at entire temperatures measured in this study. The difference from traditional ignition regime at high temperatures, the undiluted methane/air mixtures present a four-stage ignition process at lower temperatures, namely deflagration delay, deflagration, deflagration-detonation transition, and detonation. Four popular kinetic mechanisms, UBC Mech 2.1, GRI Mech 3.0, Aramco Mech 2.0, and USC Mech 2.0, were used to simulate the new measurements. Only UBC Mech 2.1 showed satisfactory predictions in the reactivity of the undiluted methane mixtures; it was, thus, adopted to perform sensitivity analysis for identifying dominant reactions in the ignition process. The difference in channels contributing ȮH radicals causes a reduced global activation energy with decreasing temperatures. Keywords: Methane; multistage ignition; shock tube; sensitivity analysis
- 26 April 2019
- Published by Art & Technology Publishing PTE. LTD. in Journal of Chemical Research and Application
- Vol. 2 (1)
Open AccessMultistage auto-ignition of undiluted methane/air mixtures under engine-relevant condition
Gas-phase auto-ignition delay times (IDTs) of methane/“air” (21% O2/79% Ar) mixtures were measured behind reflected shock waves, using a kinetic shock tube. Experiments were performed at fixed pressure of 1.8 MPa and equivalence ratios of 0.5 and 1.0, over the temperature range of 800–1000 K. Overall, the effect of equivalence ratio on IDT is negligible at entire temperatures measured in this study. The difference from traditional ignition regime at high temperatures, the undiluted methane/air mixtures present a four-stage ignition process at lower temperatures, namely deflagration delay, deflagration, deflagration-detonation transition, and detonation. Four popular kinetic mechanisms, UBC Mech 2.1, GRI Mech 3.0, Aramco Mech 2.0, and USC Mech 2.0, were used to simulate the new measurements. Only UBC Mech 2.1 showed satisfactory predictions in the reactivity of the undiluted methane mixtures; it was, thus, adopted to perform sensitivity analysis for identifying dominant reactions in the ignition process. The difference in channels contributing ȮH radicals causes a reduced global activation energy with decreasing temperatures. Keywords: Methane; multistage ignition; shock tube; sensitivity analysis
- 14 March 2019
- Published by Hindawi Limited in International Journal of Energy Research
- Vol. 43 (6) , 2312-2326
Multi‐objective optimization design of plate‐fin vapor generator for supercritical organic Rankine cycle
Supercritical organic Rankine cycle (SORC) is an improved ORC architecture with lower exergy destruction and better heat source utilization when compared with a subcritical one. The accurate design of its vapor generator is of critical importance due to the fact that heat transfer performance significantly affects thermal efficiency, power output, and size of the overall system. This paper aims to develop a mathematical model of the SORC vapor generator using plate‐fin heat exchanger. The finite volume method is applied to deal with the properties' variation problem of the supercritical fluids. Multi‐objective optimization is employed by the nondominated sorting genetic algorithm II to find the optimum geometry design. The objective functions are the number of entropy production units, annual cost, and volume. For a specific SORC system, an optimum vapor generator is designed using the developed model. Parametric studies are conducted to assess the effect of geometry parameters on the vapor generator performance. The off‐design performance of the vapor generator is also evaluated under different mass flow rates and different heat source inlet temperature conditions.
- 14 March 2019
- Published by Hindawi Limited in International Journal of Energy Research
- Vol. 43 (6) , 2312-2326
Multi‐objective optimization design of plate‐fin vapor generator for supercritical organic Rankine cycle
Supercritical organic Rankine cycle (SORC) is an improved ORC architecture with lower exergy destruction and better heat source utilization when compared with a subcritical one. The accurate design of its vapor generator is of critical importance due to the fact that heat transfer performance significantly affects thermal efficiency, power output, and size of the overall system. This paper aims to develop a mathematical model of the SORC vapor generator using plate‐fin heat exchanger. The finite volume method is applied to deal with the properties' variation problem of the supercritical fluids. Multi‐objective optimization is employed by the nondominated sorting genetic algorithm II to find the optimum geometry design. The objective functions are the number of entropy production units, annual cost, and volume. For a specific SORC system, an optimum vapor generator is designed using the developed model. Parametric studies are conducted to assess the effect of geometry parameters on the vapor generator performance. The off‐design performance of the vapor generator is also evaluated under different mass flow rates and different heat source inlet temperature conditions.
- Open Access
- 1 January 2016
- Published by Elsevier in Surface and Coatings Technology
- Vol. 286, 268-278
Uniform design for the optimization of Al2O3 nanofilms produced by electrophoretic deposition
- 1 January 2016
- Published by Elsevier in Surface and Coatings Technology
- Vol. 286, 268-278
Open AccessUniform design for the optimization of Al2O3 nanofilms produced by electrophoretic deposition