Mochamad Chalid
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Mochamad Chalid has a total of 306 co-authors. Here are the top co-authors by number of shared publications:
- Adam Febriyanto Nugraha
Green Polymer Technology Laboratory, Department of Metallurgical and Material Engineering, Faculty of Engineering, Universitas Indonesia, Depok 16424, Indonesia
9 shared publications Adam Febriyanto Nugraha
8 shared publications- Achmad Nandang Roziafanto
Food Nanotechnology Study Program Polytechnic of AKA Bogor Bogor Indonesia
6 shared publications - Azizah Intan Pangesty
Green Polymer Technology Laboratory Department of Metallurgical and Materials Engineering Faculty of Engineering Universitas Indonesia Depok Indonesia
6 shared publications - Evana Yuanita
Department of Metallurgy and Material Engineering, Faculty of Engineering, Universitas Indonesia, Depok 16424, Indonesia
6 shared publications - Aniek Sri Handayani
Indonesia Institute of Technology
5 shared publications
Latest Publications
- 14 October 2026
- Published by Wiley in Macromolecular Symposia
Influence of PVA Concentration on the Properties of Lontar Palm Leaf‐Sugarcane Bagasse Hybrid Biocomposite Films
Natural fiber‐reinforced bioplastics represent a viable strategy for valorizing agricultural waste; however, the combined reinforcement of lontar palm ( Borassus flabellifer ) leaf and sugarcane bagasse fibers in a polyvinyl alcohol (PVA) matrix remains underexplored. This study investigates the effects of varying PVA concentrations (15, 30, and 45 wt%) on the physical, mechanical, thermal, and interfacial properties of hybrid biocomposite films. Extracted cellulose fibers served as structural reinforcement. Tensile strength increased with higher PVA loading, peaking at 1.79 MPa at 45 wt% PVA, while elongation reached an optimal 43.36% at 30 wt.% PVA. Physical characterization revealed a maximum swelling of 70.3% at 45 wt.% PVA, whereas water solubility decreased from 63.54% at 15 wt.% PVA to a minimum of 55.30% at 45 wt.% PVA. The 45 wt.% formulation also exhibited superior structural and thermal stability, showing the lowest soil‐burial degradation (36.80%) and minimal heat‐induced weight loss (8.99% at 120°C). Spectroscopic analyses confirmed robust interfacial bonding via hydrogen linkages (3500–3200 cm − 1 ) and prominent C─O/C─O─C vibrations (1200–1000 cm − 1 ) between the cellulose fillers and polymer chains. Overall, balancing PVA concentration with hybrid fiber reinforcement is critical to tailoring mechanical strength, water affinity, and degradation resistance in biodegradable films
- 14 October 2026
- Published by Wiley in Macromolecular Symposia
Influence of PVA Concentration on the Properties of Lontar Palm Leaf‐Sugarcane Bagasse Hybrid Biocomposite Films
Natural fiber‐reinforced bioplastics represent a viable strategy for valorizing agricultural waste; however, the combined reinforcement of lontar palm ( Borassus flabellifer ) leaf and sugarcane bagasse fibers in a polyvinyl alcohol (PVA) matrix remains underexplored. This study investigates the effects of varying PVA concentrations (15, 30, and 45 wt%) on the physical, mechanical, thermal, and interfacial properties of hybrid biocomposite films. Extracted cellulose fibers served as structural reinforcement. Tensile strength increased with higher PVA loading, peaking at 1.79 MPa at 45 wt% PVA, while elongation reached an optimal 43.36% at 30 wt.% PVA. Physical characterization revealed a maximum swelling of 70.3% at 45 wt.% PVA, whereas water solubility decreased from 63.54% at 15 wt.% PVA to a minimum of 55.30% at 45 wt.% PVA. The 45 wt.% formulation also exhibited superior structural and thermal stability, showing the lowest soil‐burial degradation (36.80%) and minimal heat‐induced weight loss (8.99% at 120°C). Spectroscopic analyses confirmed robust interfacial bonding via hydrogen linkages (3500–3200 cm − 1 ) and prominent C─O/C─O─C vibrations (1200–1000 cm − 1 ) between the cellulose fillers and polymer chains. Overall, balancing PVA concentration with hybrid fiber reinforcement is critical to tailoring mechanical strength, water affinity, and degradation resistance in biodegradable films
- 6 October 2026
- Published by Wiley in Macromolecular Symposia
Study of Microfibrilated Cellulose (MFC) Based on Arenga Pinnata “Ijuk” Fiber as Nucleating Agent on Polypropylene Impact Copolymer
Microfibrillated Cellulose (MFC) was extracted via alkalization and bleaching treatment using NaClO and KMnO4 to replace the acid buffers. Polypropylene (PP) Impact Copolymer composites were prepared by varying MFC contents as a nucleating agent. The properties of fibers such as composition, morphology, and crystallinity index, were investigated to examine the treatment effect. Infra‐Red (IR) spectra show that lignin and hemicellulose were removed from the treatment process. The scanning electron microscopy (SEM) has done to observe the morphology of fiber and composites. Differential scanning calorimetry (DSC) was performed to analyze thermal stability and degree of crystallinity. The addition of MFC accelerates the crystallization time of PP impact copolymers.
- 6 October 2026
- Published by Wiley in Macromolecular Symposia
Study of Microfibrilated Cellulose (MFC) Based on Arenga Pinnata “Ijuk” Fiber as Nucleating Agent on Polypropylene Impact Copolymer
Microfibrillated Cellulose (MFC) was extracted via alkalization and bleaching treatment using NaClO and KMnO4 to replace the acid buffers. Polypropylene (PP) Impact Copolymer composites were prepared by varying MFC contents as a nucleating agent. The properties of fibers such as composition, morphology, and crystallinity index, were investigated to examine the treatment effect. Infra‐Red (IR) spectra show that lignin and hemicellulose were removed from the treatment process. The scanning electron microscopy (SEM) has done to observe the morphology of fiber and composites. Differential scanning calorimetry (DSC) was performed to analyze thermal stability and degree of crystallinity. The addition of MFC accelerates the crystallization time of PP impact copolymers.
- Open Access
- 23 September 2026
- Published by Universitas Gadjah Mada in Indonesian Journal of Chemistry
- Vol. 26 (5) , 1529-1545
Effect of Cellulose Chain Extender on the Molecular, Thermal, and Mechanical Characteristics of Polyurethane Foam
This study investigates the incorporation of cellulose as a bio-based modifier into polyurethane foam and its effects on molecular interactions, morphology, thermal behavior, and mechanical performance. Polyurethane foam was synthesized using polypropylene glycol (PPG 2000), toluene diisocyanate (TDI), water, and cellulose at 1, 2, and 3 wt.%. Fourier-transform infrared (FTIR) spectroscopy confirmed urethane formation and suggested subtle intermolecular interactions between cellulose and the polyurethane matrix. Scanning electron microscopy (SEM) revealed predominantly open-cell morphology, with improved cell uniformity 2 wt.% cellulose loading. Thermal analysis showed that cellulose incorporation slightly modified the endothermic transition behavior while reducing the degradation onset temperature and Tmax from 390.16 to 377.13 °C, indicating a narrower thermal stability window. Mechanical testing demonstrated that the tensile strength increased to 0.085 MPa at 2 wt.% cellulose before decreasing at higher loading, whereas the elongation at break declined due to restricted chain mobility. These findings demonstrate that controlled cellulose incorporation can tailor the mechanical performance and morphology of polyurethane foams, supporting its potential use as a sustainable bio-modified polymeric material.
- 23 September 2026
- Published by Universitas Gadjah Mada in Indonesian Journal of Chemistry
- Vol. 26 (5) , 1529-1545
Open AccessEffect of Cellulose Chain Extender on the Molecular, Thermal, and Mechanical Characteristics of Polyurethane Foam
This study investigates the incorporation of cellulose as a bio-based modifier into polyurethane foam and its effects on molecular interactions, morphology, thermal behavior, and mechanical performance. Polyurethane foam was synthesized using polypropylene glycol (PPG 2000), toluene diisocyanate (TDI), water, and cellulose at 1, 2, and 3 wt.%. Fourier-transform infrared (FTIR) spectroscopy confirmed urethane formation and suggested subtle intermolecular interactions between cellulose and the polyurethane matrix. Scanning electron microscopy (SEM) revealed predominantly open-cell morphology, with improved cell uniformity 2 wt.% cellulose loading. Thermal analysis showed that cellulose incorporation slightly modified the endothermic transition behavior while reducing the degradation onset temperature and Tmax from 390.16 to 377.13 °C, indicating a narrower thermal stability window. Mechanical testing demonstrated that the tensile strength increased to 0.085 MPa at 2 wt.% cellulose before decreasing at higher loading, whereas the elongation at break declined due to restricted chain mobility. These findings demonstrate that controlled cellulose incorporation can tailor the mechanical performance and morphology of polyurethane foams, supporting its potential use as a sustainable bio-modified polymeric material.
- Open Access
- 18 September 2026
- Published by Elsevier in Next Materials
- Vol. 13
Effects of chopped strand mat inserts and nanosilica fillers on the mechanical performance and failure behavior of CFRP laminate joggle lap-bonded joints
- 18 September 2026
- Published by Elsevier in Next Materials
- Vol. 13
Open AccessEffects of chopped strand mat inserts and nanosilica fillers on the mechanical performance and failure behavior of CFRP laminate joggle lap-bonded joints
- 7 September 2026
- Published by Springer Nature in Journal of Rubber Research
- p. 1-12
Exploring the effect of TMTD accelerator on cross-link density in EPDM rubber
- 7 September 2026
- Published by Springer Nature in Journal of Rubber Research
- p. 1-12
Exploring the effect of TMTD accelerator on cross-link density in EPDM rubber
- 4 June 2026
- Published by Springer Nature in Journal of Coatings Technology and Research
- Vol. 23 (6) , 2851-2861
Surface modification of cellulose nanofibrils with lactic acid for biodegradable coatings via grafting optimization and barrier performance
- 4 June 2026
- Published by Springer Nature in Journal of Coatings Technology and Research
- Vol. 23 (6) , 2851-2861
Surface modification of cellulose nanofibrils with lactic acid for biodegradable coatings via grafting optimization and barrier performance
- 15 April 2026
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 143 (23)
The Effect of Curing Temperature on the Thermal Conductivity of Cross‐Linked HDPE Using Peroxide With the Addition of an Antioxidant
This study investigates the effects of curing temperature on the thermal conductivity of cross‐linked high‐density polyethylene (XL‐HDPE). The specific objective is to evaluate the effect of cross‐linking with peroxides and the addition of antioxidants on the thermal conductivity the material before and after vacuum degassing at curing temperatures of 180°C, 190°C, and 200°C. High‐density polyethylene (HDPE) is used as the polymer matrix with di‐cumyl peroxide (DCP) as the crosslinking agent, and Irganox 1010 (IX‐1010) is added to mitigate the degradation of free radicals during the curing process. XL‐HDPE samples are prepared through a melt mixing process followed by hot‐pressing to ensure the homogeneous distribution of crosslinking agents and antioxidants. The thermal conductivity of XL‐HDPE is measured by comparing the thermal conductivities of XL‐HDPE with and without antioxidants before and after vacuum degassing. With the addition of 0.20 parts per hundred resin (phr) of antioxidants in the crosslinking process of HDPE with 1.01 phr of DCP significantly reduces the thermal degradation of HDPE, resulting in a higher thermal conductivity especially at 200°C which experiences the highest increase in thermal conductivity of 8.33% compared to that without antioxidants prior to vacuum degassing. Practically, this study offers a manufacturing protocol to enhance the intrinsic thermal conductivity of HDPE without conductive fillers. This particularly vital for thermal management systems in the nuclear, aerospace, and space industries, where materials must withstand vacuum environments and dissipate heat efficiently.
- 15 April 2026
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 143 (23)
The Effect of Curing Temperature on the Thermal Conductivity of Cross‐Linked HDPE Using Peroxide With the Addition of an Antioxidant
This study investigates the effects of curing temperature on the thermal conductivity of cross‐linked high‐density polyethylene (XL‐HDPE). The specific objective is to evaluate the effect of cross‐linking with peroxides and the addition of antioxidants on the thermal conductivity the material before and after vacuum degassing at curing temperatures of 180°C, 190°C, and 200°C. High‐density polyethylene (HDPE) is used as the polymer matrix with di‐cumyl peroxide (DCP) as the crosslinking agent, and Irganox 1010 (IX‐1010) is added to mitigate the degradation of free radicals during the curing process. XL‐HDPE samples are prepared through a melt mixing process followed by hot‐pressing to ensure the homogeneous distribution of crosslinking agents and antioxidants. The thermal conductivity of XL‐HDPE is measured by comparing the thermal conductivities of XL‐HDPE with and without antioxidants before and after vacuum degassing. With the addition of 0.20 parts per hundred resin (phr) of antioxidants in the crosslinking process of HDPE with 1.01 phr of DCP significantly reduces the thermal degradation of HDPE, resulting in a higher thermal conductivity especially at 200°C which experiences the highest increase in thermal conductivity of 8.33% compared to that without antioxidants prior to vacuum degassing. Practically, this study offers a manufacturing protocol to enhance the intrinsic thermal conductivity of HDPE without conductive fillers. This particularly vital for thermal management systems in the nuclear, aerospace, and space industries, where materials must withstand vacuum environments and dissipate heat efficiently.
- 24 March 2026
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 35 (10) , 1-10
Hydrogel based composite polyvinyl alcohol/sodium alginate/cellulose fiber incorporated gamat gel as potential for wound dressing
- 24 March 2026
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 35 (10) , 1-10
Hydrogel based composite polyvinyl alcohol/sodium alginate/cellulose fiber incorporated gamat gel as potential for wound dressing
- Open Access
- 11 March 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (3) , 152
Atmospheric Plasma-Treated Recycled Polyethylene (rPE) as a Compatibilizer in rPE/Oil Palm Empty Fruit Bunch Fiber Composites
Composites based on rPE and OPEFB waste are considered sustainable materials. However, their performance is limited by hydrophobic–hydrophilic incompatibility, which weakens interfacial adhesion. This study investigated the atmospheric-pressure air plasma treatment of rPE to enhance its compatibility with OPEFB fibers and evaluated its role as a compatibilizer. Atmospheric plasma treatment for 120 s introduced oxygen-containing groups onto the rPE surface, as evidenced by C-O and OH peaks in the FTIR spectra and the higher O/C ratio in the XPS analysis. Consequently, the water contact angle decreased, reducing the difference in surface tension between rPE and OPEFB from 45.61% to 7.80%. Composites containing 20 wt.% OPEFB were fabricated by varying the proportion of untreated rPE with p-rPE. All p-rPE-based composites exhibited fewer interfacial voids than untreated rPE composites, indicating improved fiber–matrix adhesion. The tensile strength and elastic modulus increased with the p-rPE content, whereas the elongation at break remained higher than that of the untreated composite. Therefore, p-rPE shows potential as a compatibilizer, enabling agricultural and plastic waste value enhancement.
- 11 March 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (3) , 152
Open AccessAtmospheric Plasma-Treated Recycled Polyethylene (rPE) as a Compatibilizer in rPE/Oil Palm Empty Fruit Bunch Fiber Composites
Composites based on rPE and OPEFB waste are considered sustainable materials. However, their performance is limited by hydrophobic–hydrophilic incompatibility, which weakens interfacial adhesion. This study investigated the atmospheric-pressure air plasma treatment of rPE to enhance its compatibility with OPEFB fibers and evaluated its role as a compatibilizer. Atmospheric plasma treatment for 120 s introduced oxygen-containing groups onto the rPE surface, as evidenced by C-O and OH peaks in the FTIR spectra and the higher O/C ratio in the XPS analysis. Consequently, the water contact angle decreased, reducing the difference in surface tension between rPE and OPEFB from 45.61% to 7.80%. Composites containing 20 wt.% OPEFB were fabricated by varying the proportion of untreated rPE with p-rPE. All p-rPE-based composites exhibited fewer interfacial voids than untreated rPE composites, indicating improved fiber–matrix adhesion. The tensile strength and elastic modulus increased with the p-rPE content, whereas the elongation at break remained higher than that of the untreated composite. Therefore, p-rPE shows potential as a compatibilizer, enabling agricultural and plastic waste value enhancement.