Eiki Kasai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Eiki Kasai has a total of 186 co-authors. Here are the top co-authors by number of shared publications:
Taichi Murakami
Graduate School of Environmental Studies Tohoku University
22 shared publications- Naohito Hayashi
Research Institute for Environmental Management Technology, National Institute of Advanced Industrial Science and Technology (AIST)
21 shared publications Takashi Nakamura
16 shared publicationsFumio Saito
Institute of Multidisciplinary Research for Advanced Materials, Tohoku University
15 shared publicationsTakazo Kawaguchi
Corporate Research & Development Laboratories, Sumitomo Metals Industries, Ltd
11 shared publicationsYasuo Omori
Iron & Steel Division, Kobe Steel, Ltd
10 shared publications
Latest Publications
- 19 September 2023
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 50, 397-410
Hydrogen-based pre-reduction of chromite: Reduction and consolidation mechanisms
- 19 September 2023
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 50, 397-410
Hydrogen-based pre-reduction of chromite: Reduction and consolidation mechanisms
- 15 June 2019
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 59 (6) , 1011-1017
Effect of Types of Carbonaceous Material and CaO Addition on Reduction Behavior of Pre-reduced Iron Ore–Carbon Composite
Utilization of iron ore-carbon composite for blast furnace has a possibility of the method to decrease carbon dioxide emission from iron and steel industry. Major iron ores consist of Fe2O3, Fe3O4, and FeOOH, which require several reduction steps through FeO to form metallic iron. When graphite and pure FeO obtained by pre-reduction are used for the raw material of composite, the reduction of iron oxide proceeds at lower temperature than that using conventional iron ore. In the actual process, raw materials such as iron ores and coke contain impurities of silica, alumina and sulfur. Furthermore, limestone is used as fluxing materials to control basicity of slag. In this study, the effect of types of carbonaceous materials and CaO addition on the reduction behavior of the composite using FeO prepared by pre-reduction was examined. Reduction temperatures of FeO composite using coke and biomass char were higher than that using graphite. The reason can be explained by the effect of sulfur contained in the carbonaceous materials. The addition of CaO which reacted with sulfur led to lowering the reduction temperature.
- 15 June 2019
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 59 (6) , 1011-1017
Effect of Types of Carbonaceous Material and CaO Addition on Reduction Behavior of Pre-reduced Iron Ore–Carbon Composite
Utilization of iron ore-carbon composite for blast furnace has a possibility of the method to decrease carbon dioxide emission from iron and steel industry. Major iron ores consist of Fe2O3, Fe3O4, and FeOOH, which require several reduction steps through FeO to form metallic iron. When graphite and pure FeO obtained by pre-reduction are used for the raw material of composite, the reduction of iron oxide proceeds at lower temperature than that using conventional iron ore. In the actual process, raw materials such as iron ores and coke contain impurities of silica, alumina and sulfur. Furthermore, limestone is used as fluxing materials to control basicity of slag. In this study, the effect of types of carbonaceous materials and CaO addition on the reduction behavior of the composite using FeO prepared by pre-reduction was examined. Reduction temperatures of FeO composite using coke and biomass char were higher than that using graphite. The reason can be explained by the effect of sulfur contained in the carbonaceous materials. The addition of CaO which reacted with sulfur led to lowering the reduction temperature.
- Open Access
- 1 November 2018
- Published by Elsevier in Powder Technology
- Vol. 339, 550-559
Inter−particle water infiltration dynamics of iron ore fines during granulation process
- 1 November 2018
- Published by Elsevier in Powder Technology
- Vol. 339, 550-559
Open AccessInter−particle water infiltration dynamics of iron ore fines during granulation process
- 15 October 2018
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 58 (10) , 1761-1767
Quantitative Evaluation of Reaction Mode and Reduction Disintegration Behavior of Iron Ore Agglomerates during Low Temperature Reduction
- 15 October 2018
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 58 (10) , 1761-1767
Quantitative Evaluation of Reaction Mode and Reduction Disintegration Behavior of Iron Ore Agglomerates during Low Temperature Reduction
- 15 August 2018
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 58 (8) , 1413-1419
In-situ Evaluation Method for Crack Generation and Propagation Behaviors of Iron Ore Burden during Low Temperature Reduction by Applying Acoustic Emission Method
In the field of ironmaking, there are few in situ non-destructive techniques for systematically evaluating the reduction behaviors of blast furnace (BF) burden materials. The standard method for the evaluation of the reduction disintegration index (RDI) includes low temperature reduction with a constant gas composition at a constant temperature followed by a cold strength test after cooling. During the reduction of iron ore burden in the BF, reduction disintegration proceeds in the course of increasing temperature through crack generation and propagation caused by volume expansion due to the reduction from hematite to magnetite. Acoustic emission (AE) method is an in situ non-destructive technique to evaluate the crack generation and propagation phenomena in various fields. In this study, we first attempted to apply AE method for a detailed in situ observation of BF burden materials by a combinational experiment of reduction disintegration. In the case of single-particle reduction, it was possible to detect AEs without friction between the sample and the waveguide giving rise to noise. Although a large number of AEs were measured during cooling of both sinter and pellet, the AE energy of the sinter was larger than that of the pellet. Furthermore, a significant number of AEs were also detected during heating of lump ore containing larger amount of combined water indicating possibility to evaluate the decrepitation behavior of such ores. By the packed bed reduction tests, which could evaluate average properties of iron ore burden, it was found that the AE energy attributed to thermal stress observed during cooling was higher than that to reduction degradation. These results suggest that it will be possible to eliminate the influence of crack generation within the iron ore burdens in the cooling stage by applying the in-situ non-destructive evaluation method developed in this study. It is also expected to apply for the quantitative estimation of the reduction disintegration behavior of burdens in the working BF.
- 15 August 2018
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 58 (8) , 1413-1419
In-situ Evaluation Method for Crack Generation and Propagation Behaviors of Iron Ore Burden during Low Temperature Reduction by Applying Acoustic Emission Method
In the field of ironmaking, there are few in situ non-destructive techniques for systematically evaluating the reduction behaviors of blast furnace (BF) burden materials. The standard method for the evaluation of the reduction disintegration index (RDI) includes low temperature reduction with a constant gas composition at a constant temperature followed by a cold strength test after cooling. During the reduction of iron ore burden in the BF, reduction disintegration proceeds in the course of increasing temperature through crack generation and propagation caused by volume expansion due to the reduction from hematite to magnetite. Acoustic emission (AE) method is an in situ non-destructive technique to evaluate the crack generation and propagation phenomena in various fields. In this study, we first attempted to apply AE method for a detailed in situ observation of BF burden materials by a combinational experiment of reduction disintegration. In the case of single-particle reduction, it was possible to detect AEs without friction between the sample and the waveguide giving rise to noise. Although a large number of AEs were measured during cooling of both sinter and pellet, the AE energy of the sinter was larger than that of the pellet. Furthermore, a significant number of AEs were also detected during heating of lump ore containing larger amount of combined water indicating possibility to evaluate the decrepitation behavior of such ores. By the packed bed reduction tests, which could evaluate average properties of iron ore burden, it was found that the AE energy attributed to thermal stress observed during cooling was higher than that to reduction degradation. These results suggest that it will be possible to eliminate the influence of crack generation within the iron ore burdens in the cooling stage by applying the in-situ non-destructive evaluation method developed in this study. It is also expected to apply for the quantitative estimation of the reduction disintegration behavior of burdens in the working BF.
- 26 July 2018
- Published by Springer Nature in Metallurgical and Materials Transactions B
- Vol. 49 (5) , 2278-2284
A New Approach to Processing Rutile from Ilmenite Ore Utilizing the Instability of Pseudobrookite
- 26 July 2018
- Published by Springer Nature in Metallurgical and Materials Transactions B
- Vol. 49 (5) , 2278-2284
A New Approach to Processing Rutile from Ilmenite Ore Utilizing the Instability of Pseudobrookite
- 1 January 2017
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 57 (9) , 1499-1508
Influence of Reducing Gas Composition on Disintegration Behavior of Iron Ore Agglomerates
- 1 January 2017
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 57 (9) , 1499-1508
Influence of Reducing Gas Composition on Disintegration Behavior of Iron Ore Agglomerates
- 1 January 2017
- Published by Iron and Steel Institute of Japan in Tetsu-to-Hagane
- Vol. 103 (6) , 357-364
Effective Utilization of KR Slag in Iron Ore Sintering Process
- 1 January 2017
- Published by Iron and Steel Institute of Japan in Tetsu-to-Hagane
- Vol. 103 (6) , 357-364
Effective Utilization of KR Slag in Iron Ore Sintering Process
- Open Access
- 1 January 2017
- Published by Iron and Steel Institute of Japan in Tetsu-to-Hagane
- Vol. 103 (6) , 348-356
Promoting Effect on Oxidation Reaction of Iron-bearing Agglomeration Agent by Melt Formation
This study was carried out to examine the way to suppress the CO 2 emissions from the iron ore sintering process through effectively utilizing the oxidation heat of iron containing material, namely iron-bearing agglomeration agent. Increase in the oxidation ratio of iron-bearing agglomeration agent in the process will lead to decrease in the amount of CO 2 emissions. In order to increase the oxidation ratio, the effect of melt formation in the iron oxide layer on the oxidation reaction of metallic iron particle covered by adhering layer of CaO, SiO 2 and magnetite ore was discussed. Changes in the O 2 concentration in outlet gas and sample bed temperature were measured by using a laboratory scale sintering simulator. Oxidation ratios of samples were calculated by the concentration of outlet gas. Oxidation ratio of metallic iron particles with adhering layer was higher than that of simple metallic iron particles. Melt formation of the iron oxide layer at surface of metallic iron particles would promote the oxidation compared to thatat solid state. When CaO concentration of the adhering layer was increased, oxidation ratio of metallic iron particle was increased until 50 mass%-CaO. In the case of CaO concentration more than 50 mass%, however, oxidation ratio was kept approximately 0.9. It suggests that an excess amount of melt formed on the surface of metallic iron particle seems to prevent the diffusion of oxygen. Adjusting the composition and amount of melt formed on the surface of iron-bearing agglomeration agent would lead higher reaction ratio.
- 1 January 2017
- Published by Iron and Steel Institute of Japan in Tetsu-to-Hagane
- Vol. 103 (6) , 348-356
Open AccessPromoting Effect on Oxidation Reaction of Iron-bearing Agglomeration Agent by Melt Formation
This study was carried out to examine the way to suppress the CO 2 emissions from the iron ore sintering process through effectively utilizing the oxidation heat of iron containing material, namely iron-bearing agglomeration agent. Increase in the oxidation ratio of iron-bearing agglomeration agent in the process will lead to decrease in the amount of CO 2 emissions. In order to increase the oxidation ratio, the effect of melt formation in the iron oxide layer on the oxidation reaction of metallic iron particle covered by adhering layer of CaO, SiO 2 and magnetite ore was discussed. Changes in the O 2 concentration in outlet gas and sample bed temperature were measured by using a laboratory scale sintering simulator. Oxidation ratios of samples were calculated by the concentration of outlet gas. Oxidation ratio of metallic iron particles with adhering layer was higher than that of simple metallic iron particles. Melt formation of the iron oxide layer at surface of metallic iron particles would promote the oxidation compared to thatat solid state. When CaO concentration of the adhering layer was increased, oxidation ratio of metallic iron particle was increased until 50 mass%-CaO. In the case of CaO concentration more than 50 mass%, however, oxidation ratio was kept approximately 0.9. It suggests that an excess amount of melt formed on the surface of metallic iron particle seems to prevent the diffusion of oxygen. Adjusting the composition and amount of melt formed on the surface of iron-bearing agglomeration agent would lead higher reaction ratio.
- Open Access
- 1 January 2017
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 57 (8) , 1384-1393
Intra–Particle Water Migration Dynamics during Iron Ore Granulation Process
The influence of iron ore properties, such as ore type, mineralogical texture, and particle size, on the intra-particle water migration dynamics were evaluated using immersion method. When immersed, ores were reached 68-78% of their final saturation in first 60 s and then approached final saturation slowly. It typically took up to 1 × 10 5 s to reach final saturation. Compared with the initial and final saturation water contents of 2.8-4.0 mass% in the case of Brazilian ores, Australian ores showed higher water contents of 5-6.4 mass% due to more porous structure. While the final saturation water content was partially explained by the porosity and total pore volume of ores, the kinetics of water migration should be considered to explain the saturation curve of different ores. In terms of mineralogical texture, porous texture showed higher final saturation water contents than dense texture. Finer particles showed higher final saturation water contents than coarser particles. A revised migration model was introduced to explain the effect of pore size distribution and trapped air. It was revealed that water migration proceeds more readily in the finer pores due to the larger capillary force, which is needed to overcome the trapped air. The water migration in the coarser pores is restrained due to the weak capillary force against trapped air, resulting in lower degree of saturation at equilibrium. Compared with Australian ores, Brazilian ores showed a lower degree of saturation due to their higher proportion of coarse pores.
- 1 January 2017
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 57 (8) , 1384-1393
Open AccessIntra–Particle Water Migration Dynamics during Iron Ore Granulation Process
The influence of iron ore properties, such as ore type, mineralogical texture, and particle size, on the intra-particle water migration dynamics were evaluated using immersion method. When immersed, ores were reached 68-78% of their final saturation in first 60 s and then approached final saturation slowly. It typically took up to 1 × 10 5 s to reach final saturation. Compared with the initial and final saturation water contents of 2.8-4.0 mass% in the case of Brazilian ores, Australian ores showed higher water contents of 5-6.4 mass% due to more porous structure. While the final saturation water content was partially explained by the porosity and total pore volume of ores, the kinetics of water migration should be considered to explain the saturation curve of different ores. In terms of mineralogical texture, porous texture showed higher final saturation water contents than dense texture. Finer particles showed higher final saturation water contents than coarser particles. A revised migration model was introduced to explain the effect of pore size distribution and trapped air. It was revealed that water migration proceeds more readily in the finer pores due to the larger capillary force, which is needed to overcome the trapped air. The water migration in the coarser pores is restrained due to the weak capillary force against trapped air, resulting in lower degree of saturation at equilibrium. Compared with Australian ores, Brazilian ores showed a lower degree of saturation due to their higher proportion of coarse pores.