Yasunori Okano
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Yasunori Okano has a total of 65 co-authors. Here are the top co-authors by number of shared publications:
- Atsushi Sekimoto
Department of Materials Engineering Science, Osaka University, Toyonaka, Osaka 560-8531, Japan
6 shared publications Sadik Dost
Univ Victoria, Crystal Growth Lab, Victoria, BC, Canada
6 shared publications- Sadik Dost
Crystal Growth Laboratory, University of Victoria, Victoria, BC V8W 3P6, Canada
6 shared publications Yasuhiro Hayakawa
Research Institute of Electronics, Shizuoka University, Hamamatsu, Shizuoka, Japan
6 shared publicationsHisashi Minakuchi
Univ Ryukyus, Dept Mech Engn, 1 Senbaru, Nishihara, Okinawa, Japan
4 shared publicationsMasahiro Kino-Oka
Department of Biotechnology, Osaka University
4 shared publications
Latest Publications
- 20 September 2021
- Published by Taylor & Francis in JOURNAL OF CHEMICAL ENGINEERING OF JAPAN
- Vol. 54 (9) , 493-499
Bayesian Optimization for Hydrodynamic Characterization of a Cylindrical Orbitally Shaken Bioreactor with a Bump at the Bottom
An orbitally shaken bioreactor is the most popular system for cell cultivation in a suspension culture owing to its unique characteristics. However, conventional bioreactors struggle to meet the anticipated demand in practical applications due to their limitations. In this study, numerical simulations are conducted to evaluate the performance of a newly developed orbitally shaken bioreactor that is equipped with a vaulted “bump” at the bottom wall. The presence of this bump significantly improves the mass transfer and cell suspension ratio in the culture medium without increasing the shear stress; it also efficiently reduces the cell aggregation in the central part at the bottom wall. In addition, to enable a suitable cell culture environment for practical applications, the Bayesian algorithm is employed to optimize the control of three parameters, namely bump height (hb), shaking velocity (ω), and shaking radius (R), of this reactor. For all the cases considered, the obtained data related to mass transfer, suspension ratio, and shear stress are analyzed. The simulation results show that the optimal bioreactor is preferable for cell cultivation compared with the initial state, owing to its high capability for mass transfer and suspending cells. It can be concluded that the methodology described in this paper is a feasible and reliable tool for performance prediction and process optimization in biotechnology.
- 20 September 2021
- Published by Taylor & Francis in JOURNAL OF CHEMICAL ENGINEERING OF JAPAN
- Vol. 54 (9) , 493-499
Bayesian Optimization for Hydrodynamic Characterization of a Cylindrical Orbitally Shaken Bioreactor with a Bump at the Bottom
An orbitally shaken bioreactor is the most popular system for cell cultivation in a suspension culture owing to its unique characteristics. However, conventional bioreactors struggle to meet the anticipated demand in practical applications due to their limitations. In this study, numerical simulations are conducted to evaluate the performance of a newly developed orbitally shaken bioreactor that is equipped with a vaulted “bump” at the bottom wall. The presence of this bump significantly improves the mass transfer and cell suspension ratio in the culture medium without increasing the shear stress; it also efficiently reduces the cell aggregation in the central part at the bottom wall. In addition, to enable a suitable cell culture environment for practical applications, the Bayesian algorithm is employed to optimize the control of three parameters, namely bump height (hb), shaking velocity (ω), and shaking radius (R), of this reactor. For all the cases considered, the obtained data related to mass transfer, suspension ratio, and shear stress are analyzed. The simulation results show that the optimal bioreactor is preferable for cell cultivation compared with the initial state, owing to its high capability for mass transfer and suspending cells. It can be concluded that the methodology described in this paper is a feasible and reliable tool for performance prediction and process optimization in biotechnology.
- 1 September 2021
- Published by Elsevier in Journal of Crystal Growth
- Vol. 570
Numerical simulation of thermo-solutal Marangoni convection in a full floating zone with radiative heat transfer under zero gravity
- 1 September 2021
- Published by Elsevier in Journal of Crystal Growth
- Vol. 570
Numerical simulation of thermo-solutal Marangoni convection in a full floating zone with radiative heat transfer under zero gravity
- 2 August 2021
- Published by Elsevier in Journal of Crystal Growth
- Vol. 573, 126280
Estimation of the diffusion coefficient of GaSb in InSb melt using Bayesian optimization and the ISS experimental results
- 2 August 2021
- Published by Elsevier in Journal of Crystal Growth
- Vol. 573, 126280
Estimation of the diffusion coefficient of GaSb in InSb melt using Bayesian optimization and the ISS experimental results
- 20 March 2021
- Published by Taylor & Francis in JOURNAL OF CHEMICAL ENGINEERING OF JAPAN
- Vol. 54 (3) , 87-92
Numerical Optimization of Particle Dispersion in Wave Bioreactor for Static Cell Cultivation
Japan's largest platform for academic e-journals: J-STAGE is a full text database for reviewed academic papers published by Japanese societies
- 20 March 2021
- Published by Taylor & Francis in JOURNAL OF CHEMICAL ENGINEERING OF JAPAN
- Vol. 54 (3) , 87-92
Numerical Optimization of Particle Dispersion in Wave Bioreactor for Static Cell Cultivation
Japan's largest platform for academic e-journals: J-STAGE is a full text database for reviewed academic papers published by Japanese societies
- Open Access
The Relative Contribution of Solutal Marangoni Convection to Thermal Marangoni Flow Instabilities in a Liquid Bridge of Smaller Aspect Ratios under Zero Gravity
The effect of solutal Marangoni convection on flow instabilities in the presence of thermal Marangoni convection in a Si-Ge liquid bridge with different aspect ratios has been investigated by three-dimensional (3D) numerical simulations under zero gravity. We consider a half-zone model of a liquid bridge between a cold (top plane) and a hot (bottom plane) disks. The highest Si concentration is on the top of the liquid bridge. The aspect ratio () drastically affects the critical Marangoni numbers: the critical solutal Marangoni number (under small thermal Marangoni numbers ()) has the same dependence on as the critical thermal Marangoni number (under small solutal Marangoni numbers ()), i.e., it decreases with increasing . The azimuthal wavenumber of the traveling wave mode increases as decreasing , i.e., larger azimuthal wavenumbers (, and 13) appear for , and only appears when is one and larger. The oscillatory modes of the hydro waves have been extracted as the spatiotemporal structures by using dynamic mode decomposition (DMD). The present study suggests a proper parameter region of quiescent steady flow suitable for crystal growth for smaller aspect ratios of the liquid bridge.Open AccessThe Relative Contribution of Solutal Marangoni Convection to Thermal Marangoni Flow Instabilities in a Liquid Bridge of Smaller Aspect Ratios under Zero Gravity
The effect of solutal Marangoni convection on flow instabilities in the presence of thermal Marangoni convection in a Si-Ge liquid bridge with different aspect ratios has been investigated by three-dimensional (3D) numerical simulations under zero gravity. We consider a half-zone model of a liquid bridge between a cold (top plane) and a hot (bottom plane) disks. The highest Si concentration is on the top of the liquid bridge. The aspect ratio () drastically affects the critical Marangoni numbers: the critical solutal Marangoni number (under small thermal Marangoni numbers ()) has the same dependence on as the critical thermal Marangoni number (under small solutal Marangoni numbers ()), i.e., it decreases with increasing . The azimuthal wavenumber of the traveling wave mode increases as decreasing , i.e., larger azimuthal wavenumbers (, and 13) appear for , and only appears when is one and larger. The oscillatory modes of the hydro waves have been extracted as the spatiotemporal structures by using dynamic mode decomposition (DMD). The present study suggests a proper parameter region of quiescent steady flow suitable for crystal growth for smaller aspect ratios of the liquid bridge. - Open Access
Optimal Control of SiC Crystal Growth in the RF-TSSG System Using Reinforcement Learning
We have developed a reinforcement learning (RL) model to control the melt flow in the radio frequency (RF) top-seeded solution growth (TSSG) process for growing more uniform SiC crystals with a higher growth rate. In the study, the electromagnetic field (EM) strength is controlled by the RL model to weaken the influence of Marangoni convection. The RL model is trained through a two-dimensional (2D) numerical simulation of the TSSG process. As a result, the growth rate under the control of the RL model is improved significantly. The optimized RF-coil parameters based on the control strategy for the 2D melt flow are used in a three-dimensional (3D) numerical simulation for model validation, which predicts a higher and more uniform growth rate. It is shown that the present RL model can significantly reduce the development cost and offers a useful means of finding the optimal RF-coil parameters.
Open AccessOptimal Control of SiC Crystal Growth in the RF-TSSG System Using Reinforcement Learning
We have developed a reinforcement learning (RL) model to control the melt flow in the radio frequency (RF) top-seeded solution growth (TSSG) process for growing more uniform SiC crystals with a higher growth rate. In the study, the electromagnetic field (EM) strength is controlled by the RL model to weaken the influence of Marangoni convection. The RL model is trained through a two-dimensional (2D) numerical simulation of the TSSG process. As a result, the growth rate under the control of the RL model is improved significantly. The optimized RF-coil parameters based on the control strategy for the 2D melt flow are used in a three-dimensional (3D) numerical simulation for model validation, which predicts a higher and more uniform growth rate. It is shown that the present RL model can significantly reduce the development cost and offers a useful means of finding the optimal RF-coil parameters.
- Open Access
- 1 April 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 778 (1)
The Numerical Estimation of Mass Transfer Coefficient of Oxygen in the Large-Scale Suspension Culture of iPS Cells
In order to practically apply induced pluripotent stem (iPS) cells to regenerative medicine, a large amount of undifferentiated iPS cells should be produced by using an automated/scaled-up suspension culture system. However, in large-scale culture, oxygen supply to iPS cells away from the gas-liquid interface can be insufficient. In this numerical study, the oxygen supply performance is quantitatively evaluated by estimating the volumetric mass transfer coefficient of oxygen in the suspension culture of iPS cells. And, focusing on shaking culture, where shear stress that causes death or differentiation of iPS cells is relatively reduced, we compare two different shaking methods: one direction rotation (ODR) and periodic alternate rotation (PAR). The validity of the volumetric mass transfer coefficient calculation is confirmed by comparison with the experiment. The PAR method is superior to the ODR method in terms of oxygen supply because of higher turbulence intensities, but it is much less energy efficient than the ODR method. In the ODR method, the cell size is thought to be non-uniform since iPS cells are aggregated due to cell sedimentation. On the other hand, in the PAR method, cell sedimentation is suppressed by controlling the Froude number (Fr).
- 1 April 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 778 (1)
Open AccessThe Numerical Estimation of Mass Transfer Coefficient of Oxygen in the Large-Scale Suspension Culture of iPS Cells
In order to practically apply induced pluripotent stem (iPS) cells to regenerative medicine, a large amount of undifferentiated iPS cells should be produced by using an automated/scaled-up suspension culture system. However, in large-scale culture, oxygen supply to iPS cells away from the gas-liquid interface can be insufficient. In this numerical study, the oxygen supply performance is quantitatively evaluated by estimating the volumetric mass transfer coefficient of oxygen in the suspension culture of iPS cells. And, focusing on shaking culture, where shear stress that causes death or differentiation of iPS cells is relatively reduced, we compare two different shaking methods: one direction rotation (ODR) and periodic alternate rotation (PAR). The validity of the volumetric mass transfer coefficient calculation is confirmed by comparison with the experiment. The PAR method is superior to the ODR method in terms of oxygen supply because of higher turbulence intensities, but it is much less energy efficient than the ODR method. In the ODR method, the cell size is thought to be non-uniform since iPS cells are aggregated due to cell sedimentation. On the other hand, in the PAR method, cell sedimentation is suppressed by controlling the Froude number (Fr).
- Open Access
Numerical Study of Three-Dimensional Melt Flows during the TSSG Process of SiC Crystal for the Influence of Input Parameters of RF-Coils and an External Rotating Magnetic Field
Three-dimensional numerical simulations were conducted for the Top-Seeded Solution Growth (TSSG) process of silicon carbide (SiC) crystals. We investigated the influence of coils frequency and peak current, and an applied rotating magnetic field (RMF) on the melt flow developing in this system. Numerical simulation results show that the Marangoni flow in the melt becomes stronger at higher coils frequencies due to the decreasing coils-induced electromagnetic field strength. Results also show that the use of external RMF may improve supersaturation uniformity along the seed if it is properly adjusted with respect to the coils-induced electromagnetic field strength. Furthermore, it is predicted that the application of RMF and seed rotation in the same direction may enhance supersaturation below the seed.
Open AccessNumerical Study of Three-Dimensional Melt Flows during the TSSG Process of SiC Crystal for the Influence of Input Parameters of RF-Coils and an External Rotating Magnetic Field
Three-dimensional numerical simulations were conducted for the Top-Seeded Solution Growth (TSSG) process of silicon carbide (SiC) crystals. We investigated the influence of coils frequency and peak current, and an applied rotating magnetic field (RMF) on the melt flow developing in this system. Numerical simulation results show that the Marangoni flow in the melt becomes stronger at higher coils frequencies due to the decreasing coils-induced electromagnetic field strength. Results also show that the use of external RMF may improve supersaturation uniformity along the seed if it is properly adjusted with respect to the coils-induced electromagnetic field strength. Furthermore, it is predicted that the application of RMF and seed rotation in the same direction may enhance supersaturation below the seed.
- 14 January 2020
- Published by Springer Nature
- p. 301-309
Numerical Investigation of Gas-Liquid Two-Phase Flow in a Stirred Tank
- 14 January 2020
- Published by Springer Nature
- p. 301-309
Numerical Investigation of Gas-Liquid Two-Phase Flow in a Stirred Tank
- Open Access
- 20 February 2019
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 268, 01001
Numerical simulation of particle dispersion in a pre-processing of a static culture
For producing high-quality induced pluripotent stem (iPS) cells in a static culture, initial placement of cells is one of the most important factors. Dense distribution of cells increases the risk of cell death. Thus, the cells need to be uniformly distributed during the preprocess of a static culture. This process depends on the operator’s experiences and has not been standardized. In this study, the authors have performed numerical simulations to investigate the efficient of cell dispersion by using OpenFOAM. The numerical domain is a square-shaped dish. Two shaking methods, one-direction and multi-direction reciprocal shaking, were considered and calculations were conducted under five oscillation frequencies. The cell colony was assumed as a solid spherical particle. The initial particles were densely positioned at the center. The numerical result showed that the multi-direction reciprocal shaking was more effective to disperse the particles than the one-direction reciprocal shaking. In addition, almost all particles at low frequency sank to the bottom and hardly dispersed. These results indicate that strong fluctuations can lift particles from the bottom, and frequent change of flow direction makes distribution area wide.
- 20 February 2019
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 268, 01001
Open AccessNumerical simulation of particle dispersion in a pre-processing of a static culture
For producing high-quality induced pluripotent stem (iPS) cells in a static culture, initial placement of cells is one of the most important factors. Dense distribution of cells increases the risk of cell death. Thus, the cells need to be uniformly distributed during the preprocess of a static culture. This process depends on the operator’s experiences and has not been standardized. In this study, the authors have performed numerical simulations to investigate the efficient of cell dispersion by using OpenFOAM. The numerical domain is a square-shaped dish. Two shaking methods, one-direction and multi-direction reciprocal shaking, were considered and calculations were conducted under five oscillation frequencies. The cell colony was assumed as a solid spherical particle. The initial particles were densely positioned at the center. The numerical result showed that the multi-direction reciprocal shaking was more effective to disperse the particles than the one-direction reciprocal shaking. In addition, almost all particles at low frequency sank to the bottom and hardly dispersed. These results indicate that strong fluctuations can lift particles from the bottom, and frequent change of flow direction makes distribution area wide.