Pavel Hron
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Pavel Hron has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Gabriele Ellen Schaumann
ES Landau, Group of Environmental and Soil Chemistry, Institute for Environmental Sciences, University of Koblenz-Landau, Fortstraße 7, 76829 Landau, Germany
2 shared publications - George Metreveli
University of Koblenz-Landau, Institute for Environmental Sciences, Group of Environmental and Soil Chemistry, Fortstraße 7, 76829 Landau, Germany
2 shared publications - Hans J. Vogel
UFZ – Helmholtz Centre for Environmental Research, Halle Saale Germany
2 shared publications - Samuel K. Kumahor
Department of Soil Physics, Helmholtz Centre for Environmental Research-UFZ, Theodor-Lieser-Strasse 4, 06120 Halle-Saale, Germany
2 shared publications Claudia Gallert
Faculty of Technology Microbiology -Biotechnology University of Applied Science Hochschule Emden/Leer Constantiaplatz 4 26723 Emden Germany
1 shared publication- Claudia Gallert
Department of Microbiology–Biotechnology, Faculty of Technology, University of Applied Sciences Emden/Leer, 26723 Emden, Germany
1 shared publication
Latest Publications
- 1 December 2016
- Published by Elsevier in Journal of Contaminant Hydrology
- Vol. 195, 31-39
Transport of soil-aged silver nanoparticles in unsaturated sand
- 1 December 2016
- Published by Elsevier in Journal of Contaminant Hydrology
- Vol. 195, 31-39
Transport of soil-aged silver nanoparticles in unsaturated sand
- 1 December 2015
- Published by Elsevier in Science of The Total Environment
- Vol. 535, 113-121
Transport of citrate-coated silver nanoparticles in unsaturated sand
- 1 December 2015
- Published by Elsevier in Science of The Total Environment
- Vol. 535, 113-121
Transport of citrate-coated silver nanoparticles in unsaturated sand
- 1 May 2015
- Published by Wiley in Vadose Zone Journal
- Vol. 14 (5) , 1-17
Application of Reactive Transport Modeling to Growth and Transport of Microorganisms in the Capillary Fringe
In the process of modeling and simulation of bacterial growth, the calibration of a numerical model to the specific experimental setup is often necessary. This study addressed the question of whether it is possible to predict the growth of microorganisms based only on independent measurements without additional calibration. To this end, flow‐through experiments with Escherichia coli (HB101 K12 pGLO) in a Hele–Shaw cell filled with quartz sand were simulated with a newly developed numerical code for reactive multiphase multicomponent flow based on an operator splitting approach. The hydraulic parameters of the sand were determined by multistep outflow experiments and the parameters of the microbial growth model from batch experiments. There was very good agreement between predicted and measured cell concentrations nondestructively determined from the fluorescence intensities of a green fluorescent protein produced by the bacterial strain. The correct description of the kinetics of gas–water phase exchange in the unsaturated zone and of cell attachment to the solid phase proved to be crucial. The operator splitting approach significantly reduced numerical dispersion in a convection‐dominated test case. It allowed a flexible adaptation of the solution strategy to the specific problem.
- 1 May 2015
- Published by Wiley in Vadose Zone Journal
- Vol. 14 (5) , 1-17
Application of Reactive Transport Modeling to Growth and Transport of Microorganisms in the Capillary Fringe
In the process of modeling and simulation of bacterial growth, the calibration of a numerical model to the specific experimental setup is often necessary. This study addressed the question of whether it is possible to predict the growth of microorganisms based only on independent measurements without additional calibration. To this end, flow‐through experiments with Escherichia coli (HB101 K12 pGLO) in a Hele–Shaw cell filled with quartz sand were simulated with a newly developed numerical code for reactive multiphase multicomponent flow based on an operator splitting approach. The hydraulic parameters of the sand were determined by multistep outflow experiments and the parameters of the microbial growth model from batch experiments. There was very good agreement between predicted and measured cell concentrations nondestructively determined from the fluorescence intensities of a green fluorescent protein produced by the bacterial strain. The correct description of the kinetics of gas–water phase exchange in the unsaturated zone and of cell attachment to the solid phase proved to be crucial. The operator splitting approach significantly reduced numerical dispersion in a convection‐dominated test case. It allowed a flexible adaptation of the solution strategy to the specific problem.
- Open Access
Application of reactive transport modelling to growth and transport of microorganisms in the capillary fringe
A multicomponent multiphase reactive transport simulator has been developed to facilitate the investigation of a large variety of phenomena in porous media including component transport, diffusion, microbiological growth and decay, cell attachment and detachment and phase exchange. The coupled problem is solved using operator splitting. This approach allows a flexible adaptation of the solution strategy to the concrete problem. Moreover, the individual submodels were optimised to be able to describe behaviour of Escherichia coli (HB101 K12 pGLO) in the capillary fringe in the presence or absence of dissolved organic carbon and oxygen under steady-state and flow conditions. Steady-state and flow through experiments in a Hele-Shaw cell, filled with quartz sand, were conducted to study eutrophic bacterial growth and transport in both saturated and unsaturated porous media. As E. coli cells can form the green fluorescent protein (GFP), the cell densities, calculated by evaluation of measured fluorescence intensities (in situ detection) were compared with the cell densities computed by numerical simulation. The comparison showed the laboratory experiments can be well described by our mathematical model.
Open AccessApplication of reactive transport modelling to growth and transport of microorganisms in the capillary fringe
A multicomponent multiphase reactive transport simulator has been developed to facilitate the investigation of a large variety of phenomena in porous media including component transport, diffusion, microbiological growth and decay, cell attachment and detachment and phase exchange. The coupled problem is solved using operator splitting. This approach allows a flexible adaptation of the solution strategy to the concrete problem. Moreover, the individual submodels were optimised to be able to describe behaviour of Escherichia coli (HB101 K12 pGLO) in the capillary fringe in the presence or absence of dissolved organic carbon and oxygen under steady-state and flow conditions. Steady-state and flow through experiments in a Hele-Shaw cell, filled with quartz sand, were conducted to study eutrophic bacterial growth and transport in both saturated and unsaturated porous media. As E. coli cells can form the green fluorescent protein (GFP), the cell densities, calculated by evaluation of measured fluorescence intensities (in situ detection) were compared with the cell densities computed by numerical simulation. The comparison showed the laboratory experiments can be well described by our mathematical model.