Shan Ren
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shan Ren has a total of 203 co-authors. Here are the top co-authors by number of shared publications:
Lu Yao
College of Materials Science and Engineering, Chongqing University, Chongqing, China
12 shared publicationsJie Yang
College of Materials Science and Engineering, Chongqing University, Chongqing 400044, China
10 shared publicationsQingcai Liu
College of Materials Science and Engineering, Chongqing University, Chongqing 400044, P.R. China
10 shared publicationsZhichao Chen
9 shared publicationsMingming Wang
8 shared publicationsXiaodi Li
Chongqing University
8 shared publications
Latest Publications
- Open Access
- 12 October 2026
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 11 (42) , 65674-65690
Co-Combustion Behavior of Coal Gangue and Corn Straw: Kinetics, Gaseous Product Evolution, and SHAP-Interpreted ANN Modeling
Coal gangue (CG) has limited fuel value because of its low carbon and high ash contents, while cocombustion with biomass may improve its thermal utilization. This study investigated the cocombustion of CG and corn straw (CS) using thermogravimetry/derivative thermogravimetry (TG/DTG), TG coupled with Fourier transform infrared spectroscopy (TG–FTIR), isoconversional kinetic analysis, and an artificial neural network (ANN) interpreted using Shapley additive explanations (SHAP). CS addition improved ignition and overall combustion performance. CG1CS3 exhibited a pronounced synergistic effect above approximately 480 °C and had the lowest mean apparent activation energy (131.7 kJ mol–1), which was 26.8% lower than that of CG (179.8 kJ mol–1). The main FTIR signals occurred between 200 and 600 °C. CS addition strengthened volatile-related bands at 300–450 °C, shifted the NO-related response toward lower temperatures, and weakened high-temperature signals tentatively assigned to CO, NO, and SO2. The ANN was developed using the 10 and 20 °C min–1 data sets and evaluated against the held-out DTG curves at 15 °C min–1, yielding R2 = 0.8566. SHAP identified temperature as the dominant predictor and indicated stage-dependent feature effects. These results support CS blending as a means of improving CG combustion and show that the ANN can interpolate DTG behavior within the investigated compositions and heating-rate range.
- 12 October 2026
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 11 (42) , 65674-65690
Open AccessCo-Combustion Behavior of Coal Gangue and Corn Straw: Kinetics, Gaseous Product Evolution, and SHAP-Interpreted ANN Modeling
Coal gangue (CG) has limited fuel value because of its low carbon and high ash contents, while cocombustion with biomass may improve its thermal utilization. This study investigated the cocombustion of CG and corn straw (CS) using thermogravimetry/derivative thermogravimetry (TG/DTG), TG coupled with Fourier transform infrared spectroscopy (TG–FTIR), isoconversional kinetic analysis, and an artificial neural network (ANN) interpreted using Shapley additive explanations (SHAP). CS addition improved ignition and overall combustion performance. CG1CS3 exhibited a pronounced synergistic effect above approximately 480 °C and had the lowest mean apparent activation energy (131.7 kJ mol–1), which was 26.8% lower than that of CG (179.8 kJ mol–1). The main FTIR signals occurred between 200 and 600 °C. CS addition strengthened volatile-related bands at 300–450 °C, shifted the NO-related response toward lower temperatures, and weakened high-temperature signals tentatively assigned to CO, NO, and SO2. The ANN was developed using the 10 and 20 °C min–1 data sets and evaluated against the held-out DTG curves at 15 °C min–1, yielding R2 = 0.8566. SHAP identified temperature as the dominant predictor and indicated stage-dependent feature effects. These results support CS blending as a means of improving CG combustion and show that the ANN can interpolate DTG behavior within the investigated compositions and heating-rate range.
- Open Access
Research Progress and Prospects on Poisoning Mechanism and Anti-Poisoning Modification of Cerium-Based NH3-SCR Denitrification Catalysts
Ammonia selective catalytic reduction (NH3-SCR) has become the mainstream core technology for denitrification of industrial sintering flue gas, owing to its high denitrification efficiency and mild reaction conditions. Cerium-based catalysts, with CeO2 as the primary component, have been identified as a promising system for replacing traditional vanadium-based and noble metal catalysts. These catalysts rely on the reversible Ce3+/Ce4+ redox cycle and exhibit favorable oxygen storage-release capacity derived from lattice oxygen migration. However, the presence of multiple impurities in industrial flue gas can lead to catalyst poisoning and restrict its industrial application. Consequently, there is an urgent need for the development of cerium-based catalysts that exhibit both high denitrification activity and excellent resistance to sulfur, heavy metal and water poisoning for the engineering application of NH3-SCR technology. The present paper undertakes a systematic analysis of the poisoning mechanisms of various pollutants on cerium-based SCR denitrification catalysts. In addition, it discusses the enhancement effects of doping modification with rare earth elements, transition metal elements and non-metallic elements on the sulfur resistance of catalysts. Furthermore, it reveals the intrinsic laws of different modification pathways in improving sulfur resistance by optimizing the electronic structure, regulating surface acidic sites and inducing the formation of oxygen vacancies. The present study provides theoretical support for the design and industrial application of anti-poisoning cerium-based catalysts.
Open AccessResearch Progress and Prospects on Poisoning Mechanism and Anti-Poisoning Modification of Cerium-Based NH3-SCR Denitrification Catalysts
Ammonia selective catalytic reduction (NH3-SCR) has become the mainstream core technology for denitrification of industrial sintering flue gas, owing to its high denitrification efficiency and mild reaction conditions. Cerium-based catalysts, with CeO2 as the primary component, have been identified as a promising system for replacing traditional vanadium-based and noble metal catalysts. These catalysts rely on the reversible Ce3+/Ce4+ redox cycle and exhibit favorable oxygen storage-release capacity derived from lattice oxygen migration. However, the presence of multiple impurities in industrial flue gas can lead to catalyst poisoning and restrict its industrial application. Consequently, there is an urgent need for the development of cerium-based catalysts that exhibit both high denitrification activity and excellent resistance to sulfur, heavy metal and water poisoning for the engineering application of NH3-SCR technology. The present paper undertakes a systematic analysis of the poisoning mechanisms of various pollutants on cerium-based SCR denitrification catalysts. In addition, it discusses the enhancement effects of doping modification with rare earth elements, transition metal elements and non-metallic elements on the sulfur resistance of catalysts. Furthermore, it reveals the intrinsic laws of different modification pathways in improving sulfur resistance by optimizing the electronic structure, regulating surface acidic sites and inducing the formation of oxygen vacancies. The present study provides theoretical support for the design and industrial application of anti-poisoning cerium-based catalysts.
- 22 July 2026
- Published by American Chemical Society (ACS) in ACS Catalysis
- Vol. 16 (15) , 14804-14817
Regulating Exciton Dissociation and Spin-Dependent Oxygen Activation via Bi-NiO Dual Active Sites for Deep Photocatalytic NO Oxidation
Efficient photocatalytic mitigation of nitrogen oxides (NOx) under ambient conditions remains challenging due to limited charge-carrier separation and poor selectivity in regulating reactive oxygen species (ROS), which often results in undesirable NO2 accumulation. In this study, bismuth molybdate (Bi2MoO6) was employed as a model photocatalyst, on which dual active sites composed of plasmonic metallic Bi nanoparticles and ultrasmall spin-polarized NiO were in situ constructed. Plasmonic Bi enhances visible-light absorption and hot-electron generation via localized surface plasmon resonance, while NiO establishes a spin-selective electron-transfer pathway that facilitates efficient O2 activation. This cooperative interface suppresses exciton recombination and promotes a superoxide (·O2–)-dominated oxidation pathway. Consequently, the optimized Bi-NiO@BMO achieves 77.0% NO removal, 76.7% nitrate selectivity, and minimal NO2 accumulation (<11 ppb), representing a 9.7-fold enhancement compared with pristine Bi2MoO6. In practical applications, the PTFE-assisted loading technique allows the material to be fixed onto ceramic foam, achieving an 84% NO removal efficiency and further enhancing photocatalytic performance. Spectroscopic analyses combined with density functional theory (DFT) calculations confirm that the plasmon–spin interaction lowers the free-energy barriers for ·O2– formation and deep NO oxidation. This work provides a mechanistic insight into plasmon-spin-regulated ROS generation and offers a rational design strategy of highly selective photocatalysts for environmental NOx abatement.
- 22 July 2026
- Published by American Chemical Society (ACS) in ACS Catalysis
- Vol. 16 (15) , 14804-14817
Regulating Exciton Dissociation and Spin-Dependent Oxygen Activation via Bi-NiO Dual Active Sites for Deep Photocatalytic NO Oxidation
Efficient photocatalytic mitigation of nitrogen oxides (NOx) under ambient conditions remains challenging due to limited charge-carrier separation and poor selectivity in regulating reactive oxygen species (ROS), which often results in undesirable NO2 accumulation. In this study, bismuth molybdate (Bi2MoO6) was employed as a model photocatalyst, on which dual active sites composed of plasmonic metallic Bi nanoparticles and ultrasmall spin-polarized NiO were in situ constructed. Plasmonic Bi enhances visible-light absorption and hot-electron generation via localized surface plasmon resonance, while NiO establishes a spin-selective electron-transfer pathway that facilitates efficient O2 activation. This cooperative interface suppresses exciton recombination and promotes a superoxide (·O2–)-dominated oxidation pathway. Consequently, the optimized Bi-NiO@BMO achieves 77.0% NO removal, 76.7% nitrate selectivity, and minimal NO2 accumulation (<11 ppb), representing a 9.7-fold enhancement compared with pristine Bi2MoO6. In practical applications, the PTFE-assisted loading technique allows the material to be fixed onto ceramic foam, achieving an 84% NO removal efficiency and further enhancing photocatalytic performance. Spectroscopic analyses combined with density functional theory (DFT) calculations confirm that the plasmon–spin interaction lowers the free-energy barriers for ·O2– formation and deep NO oxidation. This work provides a mechanistic insight into plasmon-spin-regulated ROS generation and offers a rational design strategy of highly selective photocatalysts for environmental NOx abatement.
- Open Access
- 11 March 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (11) , 11397-11410
Development of Fluorophilic Magnetic Adsorbents with Ultrahigh Adsorption Capacity from Red Mud: Defluorination Behavior and Mechanisms
To address the low fluoride (F-) adsorption capacity of red mud (RM)-based adsorbents, a novel Mn-coated RM adsorbent (Mn-RM) was prepared by Mn loading from red mud. Mn-RM features a 3D heteropolyhedral structure, which provides abundant functional groups for F- adsorption. The maximum equilibrium adsorption capacity (q max) of Mn-RM for F- is 141.83 mg/g at 298 K and pH 3.0, among the highest reported for RM-based adsorbents. The adsorption kinetics and isotherms follow the pseudo-second-order and Langmuir models, respectively, suggesting monolayer adsorption involving electrostatic attraction, pore filling, ion exchange-disproportion reaction, and metal complexation. Mn-RM demonstrates excellent recyclability, maintaining an 86.69% removal rate after five reuse cycles. Competitive ion adsorption experiments reveal that PO4 3- significantly inhibits F- adsorption, while SO4 2-, NO3 -, and Cl- have minimal effects. The adsorption efficiency and equilibrium capacity of Mn-RM for fluorinated wastewater from an AlF3 industrial facility and a coal-fired power plant are 99.54% (56.26 mg/g) and 99.16% (44.38 mg/g), respectively. Moreover, F- concentrations in both wastewaters after adsorption are below 0.2 mg/L, meeting the drinking water quality guidelines of both China and the World Health Organization (WHO).
- 11 March 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (11) , 11397-11410
Open AccessDevelopment of Fluorophilic Magnetic Adsorbents with Ultrahigh Adsorption Capacity from Red Mud: Defluorination Behavior and Mechanisms
To address the low fluoride (F-) adsorption capacity of red mud (RM)-based adsorbents, a novel Mn-coated RM adsorbent (Mn-RM) was prepared by Mn loading from red mud. Mn-RM features a 3D heteropolyhedral structure, which provides abundant functional groups for F- adsorption. The maximum equilibrium adsorption capacity (q max) of Mn-RM for F- is 141.83 mg/g at 298 K and pH 3.0, among the highest reported for RM-based adsorbents. The adsorption kinetics and isotherms follow the pseudo-second-order and Langmuir models, respectively, suggesting monolayer adsorption involving electrostatic attraction, pore filling, ion exchange-disproportion reaction, and metal complexation. Mn-RM demonstrates excellent recyclability, maintaining an 86.69% removal rate after five reuse cycles. Competitive ion adsorption experiments reveal that PO4 3- significantly inhibits F- adsorption, while SO4 2-, NO3 -, and Cl- have minimal effects. The adsorption efficiency and equilibrium capacity of Mn-RM for fluorinated wastewater from an AlF3 industrial facility and a coal-fired power plant are 99.54% (56.26 mg/g) and 99.16% (44.38 mg/g), respectively. Moreover, F- concentrations in both wastewaters after adsorption are below 0.2 mg/L, meeting the drinking water quality guidelines of both China and the World Health Organization (WHO).
- 23 September 2024
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 40 (39) , 20505-20514
Bimetallic MOFs-Derived Metal Oxides Co3O4/SnO2 Microspheres for Ultrahigh Response n-Butanol Gas Sensors
The construction of p-n heterojunctions is expected to be one of the effective means to improve gas sensitivity. In this research, p-n heterojunctions are successfully constructed by metal oxides derived from metal-organic frameworks (MOFs). MOFs-derived bimetallic Co3O4/SnO2 microspheres are prepared by precipitation. Gas-sensing performance shows that the Co3O4/SnO2 sensor exhibits an extremely high response (Ra/Rg = 641) to 20 ppm of n-butanol at 200 °C, which is 19 times that of pristine SnO2. It can detect n-butanol gas at low concentrations, has good selectivity to alcohol gas, and reduces the interference of benzene gas. The improved gas sensitivity can be attributed to the formation of a stable heterojunction between Co3O4 and SnO2, resulting in a greater resistance change of Co3O4/SnO2. Co3O4/SnO2 inherits the characteristic of high specific surface area of MOFs, which provides abundant sites for the reaction of the target gas and oxygen molecules. Finally, the gas-sensing mechanism of the Co3O4/SnO2-based sensor is discussed in detail.
- 23 September 2024
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 40 (39) , 20505-20514
Bimetallic MOFs-Derived Metal Oxides Co3O4/SnO2 Microspheres for Ultrahigh Response n-Butanol Gas Sensors
The construction of p-n heterojunctions is expected to be one of the effective means to improve gas sensitivity. In this research, p-n heterojunctions are successfully constructed by metal oxides derived from metal-organic frameworks (MOFs). MOFs-derived bimetallic Co3O4/SnO2 microspheres are prepared by precipitation. Gas-sensing performance shows that the Co3O4/SnO2 sensor exhibits an extremely high response (Ra/Rg = 641) to 20 ppm of n-butanol at 200 °C, which is 19 times that of pristine SnO2. It can detect n-butanol gas at low concentrations, has good selectivity to alcohol gas, and reduces the interference of benzene gas. The improved gas sensitivity can be attributed to the formation of a stable heterojunction between Co3O4 and SnO2, resulting in a greater resistance change of Co3O4/SnO2. Co3O4/SnO2 inherits the characteristic of high specific surface area of MOFs, which provides abundant sites for the reaction of the target gas and oxygen molecules. Finally, the gas-sensing mechanism of the Co3O4/SnO2-based sensor is discussed in detail.
- Open Access
Unveiling the Promoting Mechanism of H2 Activation on CuFeOx Catalyst for Low-Temperature CO Oxidation
The effect of H2 activation on the performance of CuFeOx catalyst for low-temperature CO oxidation was investigated. The characterizations of XRD, XPS, H2-TPR, O2-TPD, and in situ DRIFTS were employed to establish the relationship between physicochemical property and catalytic activity. The results showed that the CuFeOx catalyst activated with H2 at 100 °C displayed higher performance, which achieved 99.6% CO conversion at 175 °C. In addition, the H2 activation promoted the generation of Fe2+ species, and more oxygen vacancy could be formation with higher concentration of Oα species, which improved the migration rate of oxygen species in the reaction process. Furthermore, the reducibility of the catalyst was enhanced significantly, which increased the low-temperature activity. Moreover, the in situ DRIFTS experiments revealed that the reaction pathway of CO oxidation followed MvK mechanism at low temperature (+-CO and carbonate species were the main reactive intermediates, and the H2 activation increased the concentration of Cu+ species and accelerated the decomposition carbonate species, thus improving the catalytic performance effectively.
Open AccessUnveiling the Promoting Mechanism of H2 Activation on CuFeOx Catalyst for Low-Temperature CO Oxidation
The effect of H2 activation on the performance of CuFeOx catalyst for low-temperature CO oxidation was investigated. The characterizations of XRD, XPS, H2-TPR, O2-TPD, and in situ DRIFTS were employed to establish the relationship between physicochemical property and catalytic activity. The results showed that the CuFeOx catalyst activated with H2 at 100 °C displayed higher performance, which achieved 99.6% CO conversion at 175 °C. In addition, the H2 activation promoted the generation of Fe2+ species, and more oxygen vacancy could be formation with higher concentration of Oα species, which improved the migration rate of oxygen species in the reaction process. Furthermore, the reducibility of the catalyst was enhanced significantly, which increased the low-temperature activity. Moreover, the in situ DRIFTS experiments revealed that the reaction pathway of CO oxidation followed MvK mechanism at low temperature (+-CO and carbonate species were the main reactive intermediates, and the H2 activation increased the concentration of Cu+ species and accelerated the decomposition carbonate species, thus improving the catalytic performance effectively.
- 23 January 2024
- Published by Walter de Gruyter GmbH in Zeitschrift für Physikalische Chemie
- Vol. 238 (7) , 1207-1265
Removal of CO in flue gas by catalytic oxidation: a review
Most coal-fired industrial flue gases contained low concentration CO. How to deal with it effectively was a research hotspot in recent years. Catalytic oxidation was considered as the most promising method in the 21st century for the removement of CO with the high efficiency, environmentally friendly, easy to operate and low cost. In this review, the reaction mechanisms of CO oxidation were described, which could provide ideas for the development of new catalysts. The effects of supports and preparation methods on catalysts activity was also reviewed systematically. In addition, some suggestions and outlooks were provided for future development of CO catalytic oxidation.
- 23 January 2024
- Published by Walter de Gruyter GmbH in Zeitschrift für Physikalische Chemie
- Vol. 238 (7) , 1207-1265
Removal of CO in flue gas by catalytic oxidation: a review
Most coal-fired industrial flue gases contained low concentration CO. How to deal with it effectively was a research hotspot in recent years. Catalytic oxidation was considered as the most promising method in the 21st century for the removement of CO with the high efficiency, environmentally friendly, easy to operate and low cost. In this review, the reaction mechanisms of CO oxidation were described, which could provide ideas for the development of new catalysts. The effects of supports and preparation methods on catalysts activity was also reviewed systematically. In addition, some suggestions and outlooks were provided for future development of CO catalytic oxidation.
- 4 January 2024
- Published by Walter de Gruyter GmbH in International Journal of Chemical Reactor Engineering
- Vol. 22 (3) , 219-230
Research progress and perspectives of biogas production from municipal organic solid waste
Anaerobic digestion is a prevailing technology for the treatment and utilization of municipal organic solid waste (MOSW). In this technology, the macromolecular organic matter in waste degrades into small molecular substances through the anaerobic decomposition of microorganisms, producing biogas that can provide enormous energy. This paper focuses on the research progress of anaerobic digestion of various organic wastes for biogas production. The principle and process of anaerobic digestion for biogas production are introduced, along with the key factors affecting anaerobic digestion efficiency, such as temperature, pH, and sealing conditions. At the same time, the current cycle treatment technology and comprehensive treatment system of MOSW are also summarized. Furthermore, the paper explores biogas purification technologies, including desulfurization, deoxidation, drying, and decarbonization. Finally, the state-of-the-art of the utilization of MOSW for biogas production in the world and the problems faced by the utilization of MOSW for biogas production in China are reviewed. By summarizing the anaerobic digestion technology of MOSW, this review hopes to provide some reasonable solutions for the high-value utilization of MOSW.
- 4 January 2024
- Published by Walter de Gruyter GmbH in International Journal of Chemical Reactor Engineering
- Vol. 22 (3) , 219-230
Research progress and perspectives of biogas production from municipal organic solid waste
Anaerobic digestion is a prevailing technology for the treatment and utilization of municipal organic solid waste (MOSW). In this technology, the macromolecular organic matter in waste degrades into small molecular substances through the anaerobic decomposition of microorganisms, producing biogas that can provide enormous energy. This paper focuses on the research progress of anaerobic digestion of various organic wastes for biogas production. The principle and process of anaerobic digestion for biogas production are introduced, along with the key factors affecting anaerobic digestion efficiency, such as temperature, pH, and sealing conditions. At the same time, the current cycle treatment technology and comprehensive treatment system of MOSW are also summarized. Furthermore, the paper explores biogas purification technologies, including desulfurization, deoxidation, drying, and decarbonization. Finally, the state-of-the-art of the utilization of MOSW for biogas production in the world and the problems faced by the utilization of MOSW for biogas production in China are reviewed. By summarizing the anaerobic digestion technology of MOSW, this review hopes to provide some reasonable solutions for the high-value utilization of MOSW.