Romnick Unabia
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Romnick Unabia has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Lech Pawłowski
University of Limoges
2 shared publications Bianca Rae Sambo
Department of Physics, College of Science and Mathematics, Mindanao State University, Iligan Institute of Technology, A. Bonifacio Ave., Iligan City 9200, Philippines
1 shared publicationDevis Bellucci
Dipartimento di Ingegneria "Enzo Ferrari" (DIEF), University of Modena and Reggio Emilia, Modena, Italy
1 shared publicationJess Gambe
Department of Physics, College of Science and Mathematics, Mindanao State University, Iligan Institute of Technology, A. Bonifacio Ave., Iligan City 9200, Philippines
1 shared publicationJohn Robert Guerrero
School of Graduate Studies, College of Science and Mathematics, Mindanao State University, Iligan Institute of Technology, A. Bonifacio Ave., Iligan City 9200, Philippines
1 shared publicationJoy Cristy Piagola
School of Graduate Studies, College of Science and Mathematics, Mindanao State University, Iligan Institute of Technology, A. Bonifacio Ave., Iligan City 9200, Philippines
1 shared publication
Latest Publications
- 24 February 2020
- Published by Wiley in Journal of Biomedical Materials Research Part B: Applied Biomaterials
- Vol. 108 (6) , 2579-2589
In vitro studies of solution precursor plasma‐sprayed copper‐doped hydroxyapatite coatings with increasing copper content
In this present study, in vitro characterization on bioactivity and biocompatibility of the copper‐doped hydroxyapatite (Cu‐HA) coatings deposited onto Ti6Al4V alloy with increasing copper content obtained using solution precursor plasma spray process were evaluated under simulated body fluid (SBF) and cytotoxicity tests. The growth of flake‐like structures was observed at the coatings' surface after 7 days of immersion in SBF. Elemental composition analysis showed a calcium‐deficient carbonate‐containing apatite for the grown layer. Broadening of the HA peaks were also observed in the X‐ray diffraction patterns and infrared absorption spectra of the immersed coatings associated with the possible formation of an amorphous layer at the surface of the coatings. Copper incorporation does not alter the bioactivity of HA but only slowed down for 10 mol% copper content. Cytotoxicity evaluation using MTT assays showed that 3 mol% Cu‐HA coating was not toxic under in vitro characterizations.
- 24 February 2020
- Published by Wiley in Journal of Biomedical Materials Research Part B: Applied Biomaterials
- Vol. 108 (6) , 2579-2589
In vitro studies of solution precursor plasma‐sprayed copper‐doped hydroxyapatite coatings with increasing copper content
In this present study, in vitro characterization on bioactivity and biocompatibility of the copper‐doped hydroxyapatite (Cu‐HA) coatings deposited onto Ti6Al4V alloy with increasing copper content obtained using solution precursor plasma spray process were evaluated under simulated body fluid (SBF) and cytotoxicity tests. The growth of flake‐like structures was observed at the coatings' surface after 7 days of immersion in SBF. Elemental composition analysis showed a calcium‐deficient carbonate‐containing apatite for the grown layer. Broadening of the HA peaks were also observed in the X‐ray diffraction patterns and infrared absorption spectra of the immersed coatings associated with the possible formation of an amorphous layer at the surface of the coatings. Copper incorporation does not alter the bioactivity of HA but only slowed down for 10 mol% copper content. Cytotoxicity evaluation using MTT assays showed that 3 mol% Cu‐HA coating was not toxic under in vitro characterizations.
- Open Access
Current Progress in Solution Precursor Plasma Spraying of Cermets: A Review
Ceramic and metal composites, known also as cermets, may considerably improve many material properties with regards to that of initial components. Hence, cermets are frequently applied in many technological fields. Among many processes which can be employed for cermet manufacturing, thermal spraying is one of the most frequently used. Conventional plasma spraying of powders is a popular and cost-effective manufacturing process. One of its most recent innovations, called solution precursor plasma spraying (SPPS), is an emerging coating deposition method which uses homogeneously mixed solution precursors as a feedstock. The technique enables a single-step deposition avoiding the powder preparation procedures. The nanostructured coatings developed by SPPS increasingly find a place in the field of surface engineering. The present review shows the recent progress in the fabrication of cermets using SPPS. The influence of starting solution precursors, such as their chemistry, concentration, and solvents used, to the micro-structural characteristics of cermet coatings is discussed. The effect of the operational plasma spray process parameters such as solution injection mode to the deposition process and coatings’ microstructure is also presented. Moreover, the advantages of the SPPS process and its drawbacks compared to the conventional powder plasma spraying process are discussed. Finally, some applications of SPPS cermet coatings are presented to understand the potential of the process.
Open AccessCurrent Progress in Solution Precursor Plasma Spraying of Cermets: A Review
Ceramic and metal composites, known also as cermets, may considerably improve many material properties with regards to that of initial components. Hence, cermets are frequently applied in many technological fields. Among many processes which can be employed for cermet manufacturing, thermal spraying is one of the most frequently used. Conventional plasma spraying of powders is a popular and cost-effective manufacturing process. One of its most recent innovations, called solution precursor plasma spraying (SPPS), is an emerging coating deposition method which uses homogeneously mixed solution precursors as a feedstock. The technique enables a single-step deposition avoiding the powder preparation procedures. The nanostructured coatings developed by SPPS increasingly find a place in the field of surface engineering. The present review shows the recent progress in the fabrication of cermets using SPPS. The influence of starting solution precursors, such as their chemistry, concentration, and solvents used, to the micro-structural characteristics of cermet coatings is discussed. The effect of the operational plasma spray process parameters such as solution injection mode to the deposition process and coatings’ microstructure is also presented. Moreover, the advantages of the SPPS process and its drawbacks compared to the conventional powder plasma spraying process are discussed. Finally, some applications of SPPS cermet coatings are presented to understand the potential of the process.
- 9 April 2015
- Published by Wiley in physica status solidi (c)
- Vol. 12 (6) , 572-575
Synthesis and characterization of nanocrystalline hydroxyapatite and biphasic calcium phosphate using Ca(OH) 2 and (NH 4 )H 2 PO 4
- 9 April 2015
- Published by Wiley in physica status solidi (c)
- Vol. 12 (6) , 572-575
Synthesis and characterization of nanocrystalline hydroxyapatite and biphasic calcium phosphate using Ca(OH) 2 and (NH 4 )H 2 PO 4