Bo Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Bo Yang has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
Shuwei Wei
College of Environment and Safety Engineering, Qingdao University of Science & Technology, Qingdao, China
4 shared publicationsJiaming Cai
Qingdao University of Science & Technology
3 shared publicationsJun Liu
Qingdao University of Science & Technology
3 shared publicationsKun Tang
College of Environment and Safety Engineering, Qingdao University of Science & Technology, Qingdao, China
3 shared publicationsNanzhu Nie
College of Environment and Safety Engineering, Qingdao University of Science & Technology, Qingdao, China
3 shared publicationsXuejun Zhai
College of Environment and Safety Engineering, Qingdao University of Science & Technology, Qingdao, China
3 shared publications
Latest Publications
- 7 May 2021
- Published by Springer Nature in Catalysis Letters
- Vol. 152 (2) , 383-397
Study on the Degradation Performance of 2,4-DCP by Modified Co–Ni–Fe Hydrotalcite
- 7 May 2021
- Published by Springer Nature in Catalysis Letters
- Vol. 152 (2) , 383-397
Study on the Degradation Performance of 2,4-DCP by Modified Co–Ni–Fe Hydrotalcite
- 30 March 2021
- Published by Springer Nature in Applied Biochemistry and Biotechnology
- Vol. 193 (8) , 2547-2566
Preparation of Functionalized Mesoporous Silica as a Novel Carrier and Immobilization of Laccase
Amino-modified mesoporous silica (SBA-15-NH2) was prepared by hydrothermal method, which is a kind of excellent carrier for enzyme immobilization. The structure of SBA-15 was characterized by SEM and FTIR, which proved that amino group was successfully attached to the surface of SBA-15. The carrier had good mesoporous structure proved by nitrogen adsorption and desorption test. Using SBA-15-NH2 as the carrier, the optimal conditions of laccase immobilization by two different cross-linking methods were explored. At the same time, the properties of the immobilized enzyme and free enzyme were compared. The results showed that the activity of immobilized laccase by two-step method (2977.5 U/g) was much higher than that by one-step method (239.5 U/g). The optimal conditions were as follows: free laccase (35°C, pH=4.5), two-step immobilized laccase (40°C, pH=4.0), one-step immobilized laccase (35°C, pH=4.0). The two-step method was more adaptable to temperature. The pH adaptation range of the immobilized enzyme is wider, and the thermal stability is greatly enhanced. After five cycles of repeated reaction, the residual enzyme activity of two-step and one-step methods was 56% and 43% of the original. The treatment of simulated wastewater containing 2,4-dichlorophenol (2,4-DCP) by immobilized laccase was also studied. Under optimum conditions (40°C, pH=5.0, 20 mg/L), the removal of 2,4-DCP reached 89.06%. The immobilized laccase is really effective for treatment of 2,4-DCP-containing wastewater
- 30 March 2021
- Published by Springer Nature in Applied Biochemistry and Biotechnology
- Vol. 193 (8) , 2547-2566
Preparation of Functionalized Mesoporous Silica as a Novel Carrier and Immobilization of Laccase
Amino-modified mesoporous silica (SBA-15-NH2) was prepared by hydrothermal method, which is a kind of excellent carrier for enzyme immobilization. The structure of SBA-15 was characterized by SEM and FTIR, which proved that amino group was successfully attached to the surface of SBA-15. The carrier had good mesoporous structure proved by nitrogen adsorption and desorption test. Using SBA-15-NH2 as the carrier, the optimal conditions of laccase immobilization by two different cross-linking methods were explored. At the same time, the properties of the immobilized enzyme and free enzyme were compared. The results showed that the activity of immobilized laccase by two-step method (2977.5 U/g) was much higher than that by one-step method (239.5 U/g). The optimal conditions were as follows: free laccase (35°C, pH=4.5), two-step immobilized laccase (40°C, pH=4.0), one-step immobilized laccase (35°C, pH=4.0). The two-step method was more adaptable to temperature. The pH adaptation range of the immobilized enzyme is wider, and the thermal stability is greatly enhanced. After five cycles of repeated reaction, the residual enzyme activity of two-step and one-step methods was 56% and 43% of the original. The treatment of simulated wastewater containing 2,4-dichlorophenol (2,4-DCP) by immobilized laccase was also studied. Under optimum conditions (40°C, pH=5.0, 20 mg/L), the removal of 2,4-DCP reached 89.06%. The immobilized laccase is really effective for treatment of 2,4-DCP-containing wastewater
- Open Access
- 18 February 2021
- Published by Springer Nature in Research Square
Preparation of functionalized mesoporous silica as a novel carrier and immobilization of laccase
Amino modified mesoporous silica (SBA-15-NH2) was prepared by hydrothermal method, which is a kind of excellent carrier for enzyme immobilization. The structure of SBA-15 was characterized by SEM and FTIR, which proved that amino group was successfully attached to the surface of SBA-15. The carrier had good mesoporous structure by nitrogen adsorption and desorption test. Using SBA-15-NH2 as the carrier, the optimal conditions of laccase immobilization by two different cross-linking methods were explored. At the same time, the properties of immobilized enzyme and free enzyme were compared. The results showed that the activity of immobilized laccase by two-step method (2977.5 U/g) was much higher than that by one-step method (239.5 U/g). The optimal conditions were as follows: free laccase (35℃, pH = 4.5), two-step immobilized laccase (40℃, pH = 4.0), one-step immobilized laccase (35℃, pH = 4.0). The two-step method was more adaptable to temperature. The pH adaptation range of immobilized enzyme was wider, and the thermal stability was greatly enhanced. After five cycles of repeated reaction, the residual enzyme activity of two-step and one-step methods were 56% and 43% of the original. The treatment of simulated wastewater containing 2,4-dichlorophenol (2,4-DCP) by immobilized laccase was also studied. Under the optimum conditions (40℃, pH = 5.0, 20 mg/L), the removal of 2,4-DCP can reach 89.06%.
- 18 February 2021
- Published by Springer Nature in Research Square
Open AccessPreparation of functionalized mesoporous silica as a novel carrier and immobilization of laccase
Amino modified mesoporous silica (SBA-15-NH2) was prepared by hydrothermal method, which is a kind of excellent carrier for enzyme immobilization. The structure of SBA-15 was characterized by SEM and FTIR, which proved that amino group was successfully attached to the surface of SBA-15. The carrier had good mesoporous structure by nitrogen adsorption and desorption test. Using SBA-15-NH2 as the carrier, the optimal conditions of laccase immobilization by two different cross-linking methods were explored. At the same time, the properties of immobilized enzyme and free enzyme were compared. The results showed that the activity of immobilized laccase by two-step method (2977.5 U/g) was much higher than that by one-step method (239.5 U/g). The optimal conditions were as follows: free laccase (35℃, pH = 4.5), two-step immobilized laccase (40℃, pH = 4.0), one-step immobilized laccase (35℃, pH = 4.0). The two-step method was more adaptable to temperature. The pH adaptation range of immobilized enzyme was wider, and the thermal stability was greatly enhanced. After five cycles of repeated reaction, the residual enzyme activity of two-step and one-step methods were 56% and 43% of the original. The treatment of simulated wastewater containing 2,4-dichlorophenol (2,4-DCP) by immobilized laccase was also studied. Under the optimum conditions (40℃, pH = 5.0, 20 mg/L), the removal of 2,4-DCP can reach 89.06%.
- 20 November 2019
- Published by Springer Nature in Journal of Polymers and the Environment
- Vol. 28 (1) , 343-353
Preparation of Chitosan/NiFe-Layered Double Hydroxides Composites and Its Fenton-Like Catalytic Oxidation of Phenolic Compounds
- 20 November 2019
- Published by Springer Nature in Journal of Polymers and the Environment
- Vol. 28 (1) , 343-353
Preparation of Chitosan/NiFe-Layered Double Hydroxides Composites and Its Fenton-Like Catalytic Oxidation of Phenolic Compounds
- 15 January 2019
- Published by Springer Nature in Journal of Environmental Health Science and Engineering
- Vol. 17 (1) , 135-140
Optimum removal conditions of aniline compounds in simulated wastewater by laccase from white-rot fungi
Aniline compounds are widely applied as important chemical raw materials. However, they are so toxic and harmful to humans and environment that they need to be removed by an effective and economic approach, such as enzymatic reaction, which is in line with contemporary green development concepts. The effects of major factors, such as temperature, reaction time, concentration of laccase and the initial concentration of substrate on the removal of substrate were investigated by OFAT approach. After simulated wastewater is treated with enzymes, aniline concentration was determined by N-(1-Naphthyl)ethylene-diamine dihydrochloride spectrophotometric method. Concentration of o-phenylenediamine was determined by ferric ammonium alum spectrophotometric method. For the removal of aniline, the optimum conditions were as follows: 50 °C, initial aniline concentration of 80 mg/L and laccase concentration of 1 g/L. In this case, the total removal of aniline reached 97.1% after 8 h, this also involves the volatilization of aniline itself. The optimum conditions of o-phenylenediamine were as follows: 50 °C, initial concentration of 100 mg/L and laccase concentration of 1 g/L. Under the above condition, the o-phenylenediamine could be removed completely after 60 min. The results show that the removal of aniline compounds by laccase from white-rot fungi has good effect and potential application prospect.
- 15 January 2019
- Published by Springer Nature in Journal of Environmental Health Science and Engineering
- Vol. 17 (1) , 135-140
Optimum removal conditions of aniline compounds in simulated wastewater by laccase from white-rot fungi
Aniline compounds are widely applied as important chemical raw materials. However, they are so toxic and harmful to humans and environment that they need to be removed by an effective and economic approach, such as enzymatic reaction, which is in line with contemporary green development concepts. The effects of major factors, such as temperature, reaction time, concentration of laccase and the initial concentration of substrate on the removal of substrate were investigated by OFAT approach. After simulated wastewater is treated with enzymes, aniline concentration was determined by N-(1-Naphthyl)ethylene-diamine dihydrochloride spectrophotometric method. Concentration of o-phenylenediamine was determined by ferric ammonium alum spectrophotometric method. For the removal of aniline, the optimum conditions were as follows: 50 °C, initial aniline concentration of 80 mg/L and laccase concentration of 1 g/L. In this case, the total removal of aniline reached 97.1% after 8 h, this also involves the volatilization of aniline itself. The optimum conditions of o-phenylenediamine were as follows: 50 °C, initial concentration of 100 mg/L and laccase concentration of 1 g/L. Under the above condition, the o-phenylenediamine could be removed completely after 60 min. The results show that the removal of aniline compounds by laccase from white-rot fungi has good effect and potential application prospect.
- 11 December 2018
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 26 (4) , 3814-3822
Preparation of chitosan/Co-Fe-layered double hydroxides and its performance for removing 2,4-dichlorophenol
Chitosan/Co-Fe-layered double hydroxides (CS/LDHs) were prepared by coprecipitation method, which is a kind of composite material with excellent properties. The structure of CS/LDHs was characterized by SEM, FTIR, and XRD, which proved that chitosan (CS) was successfully induced into hydrotalcite and CS/LDHs still possess the structural characteristics of hydrotalcite. The adsorption of 2,4-dichlorophenol (2,4-DCP) was studied with CS/LDHs and LDHs as adsorbent separately. The activity of immobilized laccase (L-CS/LDHs) with CS/LDHs as carrier is significantly better than that of the one (L-LDHs) using LDHs as carrier. Under the optimum conditions (pH = 6, 55 °C, 48 h), L-CS/LDHs exhibited better removal performance for 2,4-DCP (81.53%, 100 mg/L) than LDHs (63.55%); the removal of 2,4-DCP by L-CS/LDHs is excellent, exceeding 97% as its initial concentration below 60 mg/L. It includes the catalytic action of laccase and dechlorination of Fe3+ and Co2+, and the adsorption can be ignored under the optimal conditions. After 5 cycles, it maintained 67% (L-CS/LDHs) and 54% (L-LDHs) of the original removal.
- 11 December 2018
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 26 (4) , 3814-3822
Preparation of chitosan/Co-Fe-layered double hydroxides and its performance for removing 2,4-dichlorophenol
Chitosan/Co-Fe-layered double hydroxides (CS/LDHs) were prepared by coprecipitation method, which is a kind of composite material with excellent properties. The structure of CS/LDHs was characterized by SEM, FTIR, and XRD, which proved that chitosan (CS) was successfully induced into hydrotalcite and CS/LDHs still possess the structural characteristics of hydrotalcite. The adsorption of 2,4-dichlorophenol (2,4-DCP) was studied with CS/LDHs and LDHs as adsorbent separately. The activity of immobilized laccase (L-CS/LDHs) with CS/LDHs as carrier is significantly better than that of the one (L-LDHs) using LDHs as carrier. Under the optimum conditions (pH = 6, 55 °C, 48 h), L-CS/LDHs exhibited better removal performance for 2,4-DCP (81.53%, 100 mg/L) than LDHs (63.55%); the removal of 2,4-DCP by L-CS/LDHs is excellent, exceeding 97% as its initial concentration below 60 mg/L. It includes the catalytic action of laccase and dechlorination of Fe3+ and Co2+, and the adsorption can be ignored under the optimal conditions. After 5 cycles, it maintained 67% (L-CS/LDHs) and 54% (L-LDHs) of the original removal.
- 14 December 2017
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 40 (3) , 351-357
The characteristics of air pollutants from the combustion of biomass pellets
Biomass is renewable clean energy. The aim of this study is to explore the combustion properties and emission characteristics of NOX, SO2, PM, and HCl in the combustion process of biomass pellet fuels. In this study, three kinds of fuels (pine sawdust, mixed wood, and corn straw) were selected to be studied by using a tube furnace to simulate industrial boiler. Experiments were conducted under different combustion conditions (combustion temperature and air flow). The results show that pollutant emissions were related to fuel type, combustion temperature, and air flow. The emissions of NOX were contingent on N content in the fuel and the peak emissions of NOX appeared in the range of 50~600 mg/m3 at 4 L/min and 700℃. The emissions of SO2 were related to combustion condition and close to zero under the condition of sufficient combustion. The emissions of HCl and particulate matter (PM) increase with the rise of temperature, but the emission of PM was minimal at 800℃. Average HCl emission was 0.2~0.5 mg/g under steady-state conditions (4 L/min and 700℃). All in all, the pollutant emissions of biomass pellet fuels during combustion are lower than those of the traditional fuel, and the combustion efficiency is relatively higher.
- 14 December 2017
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 40 (3) , 351-357
The characteristics of air pollutants from the combustion of biomass pellets
Biomass is renewable clean energy. The aim of this study is to explore the combustion properties and emission characteristics of NOX, SO2, PM, and HCl in the combustion process of biomass pellet fuels. In this study, three kinds of fuels (pine sawdust, mixed wood, and corn straw) were selected to be studied by using a tube furnace to simulate industrial boiler. Experiments were conducted under different combustion conditions (combustion temperature and air flow). The results show that pollutant emissions were related to fuel type, combustion temperature, and air flow. The emissions of NOX were contingent on N content in the fuel and the peak emissions of NOX appeared in the range of 50~600 mg/m3 at 4 L/min and 700℃. The emissions of SO2 were related to combustion condition and close to zero under the condition of sufficient combustion. The emissions of HCl and particulate matter (PM) increase with the rise of temperature, but the emission of PM was minimal at 800℃. Average HCl emission was 0.2~0.5 mg/g under steady-state conditions (4 L/min and 700℃). All in all, the pollutant emissions of biomass pellet fuels during combustion are lower than those of the traditional fuel, and the combustion efficiency is relatively higher.
- Open Access
- 30 April 2016
- Published by IWA Publishing in Journal of Water Reuse and Desalination
- Vol. 7 (2) , 197-204
Indirect anodic oxidation applied for treatment of simulated wastewater containing Cationic Red X-GRL and Disperse Red 3B
The treatment of simulated wastewater containing Cationic Red X-GRL (X-GRL) or Disperse Red 3B (DR-3B) dye was carried out by indirect anodic oxidation, using Ti/SnO2 electrodes as the anode. The influences of pH value, voltage, electrolysis time and sodium chloride dosage on the degradation performance were studied by single factor experiment. Furthermore the nitrogen states and UV-Vis spectra in dyes degradation were analyzed. The results showed that under the optimum condition (pH = 3, voltage = 20 V, NaCl = 2.5 g/L), the decolorization and chemical oxygen demand removal of X-GRL were 98% and 67%, respectively; and those of DR-3B were 51% and 61%, respectively. The azo double bond conjugated system in X-GRL is much more easily destroyed than the anthraquinone conjugated system in DR-3B; the aryl ring structures of them can be partially degraded.
- 30 April 2016
- Published by IWA Publishing in Journal of Water Reuse and Desalination
- Vol. 7 (2) , 197-204
Open AccessIndirect anodic oxidation applied for treatment of simulated wastewater containing Cationic Red X-GRL and Disperse Red 3B
The treatment of simulated wastewater containing Cationic Red X-GRL (X-GRL) or Disperse Red 3B (DR-3B) dye was carried out by indirect anodic oxidation, using Ti/SnO2 electrodes as the anode. The influences of pH value, voltage, electrolysis time and sodium chloride dosage on the degradation performance were studied by single factor experiment. Furthermore the nitrogen states and UV-Vis spectra in dyes degradation were analyzed. The results showed that under the optimum condition (pH = 3, voltage = 20 V, NaCl = 2.5 g/L), the decolorization and chemical oxygen demand removal of X-GRL were 98% and 67%, respectively; and those of DR-3B were 51% and 61%, respectively. The azo double bond conjugated system in X-GRL is much more easily destroyed than the anthraquinone conjugated system in DR-3B; the aryl ring structures of them can be partially degraded.
- Open Access
Impact of Rural Domestic Wastewater Irrigation on the Physicochemical and Microbiological Properties of Pakchoi and Soil
Great attention has been paid to the potential of wastewater irrigation as a sustainable water source, particularly due to water scarcity and water pollution issues. However, few studies have focused on its adverse effects and on the health risks it may pose. In this study, the physicochemical properties of soils and plants irrigated with rural domestic wastewater and associated microbiological risks were investigated. The results showed that sewage irrigation could increase the production of vegetables and improve soil fertility. While the nitrate content of plants increased significantly, pathogens on plants and in soils increased after irrigation with raw wastewater. In particular, there was a wide range of pathogenic bacteria in the phyllosphere, which may indicate risks if contaminated vegetables are consumed directly. Treated wastewater irrigation was not significantly different from controls, which were irrigated by tap water; consequently, it can be used as an alternative water resource for agricultural irrigation. The presence of a wide spectrum pathogens in wastewater shows the necessity of long-term monitoring and further evaluation.
Open AccessImpact of Rural Domestic Wastewater Irrigation on the Physicochemical and Microbiological Properties of Pakchoi and Soil
Great attention has been paid to the potential of wastewater irrigation as a sustainable water source, particularly due to water scarcity and water pollution issues. However, few studies have focused on its adverse effects and on the health risks it may pose. In this study, the physicochemical properties of soils and plants irrigated with rural domestic wastewater and associated microbiological risks were investigated. The results showed that sewage irrigation could increase the production of vegetables and improve soil fertility. While the nitrate content of plants increased significantly, pathogens on plants and in soils increased after irrigation with raw wastewater. In particular, there was a wide range of pathogenic bacteria in the phyllosphere, which may indicate risks if contaminated vegetables are consumed directly. Treated wastewater irrigation was not significantly different from controls, which were irrigated by tap water; consequently, it can be used as an alternative water resource for agricultural irrigation. The presence of a wide spectrum pathogens in wastewater shows the necessity of long-term monitoring and further evaluation.