SLShu Li

Shu Li

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Shu Li has a total of 18 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Study on Tribological Behavior of Zinc Phosphate Impregnated Graphite Under Oil Lubrication Condition

    by Jianhang Chen, Siyang Gao, Peng Wang, Weihai Xue, Shu Li, Deli Duan

    The tribological behavior of zinc phosphate impregnated graphite (ZPIG) against nickel-based superalloy (GH4169) in oil environment was investigated, and the lubrication and wear mechanism were also determined in this study. Tribological tests were run under different tribological conditions using a ring-on-disk device. The results showed that, under any load conditions, zinc phosphate impregnated graphite had the lowest coefficient of friction (COF) and wear-rate at 200 rpm. Under the identical rotating speed condition, the minimum coefficient of friction and wear-rate were obtained when the load was 500 N and 1000 N. The lubrication mechanism, which could be reflected by the transfer layer of friction counterpart, was related to the coefficient of friction, wear-rate, and oil temperature to affect contact characteristics of two solid surfaces and formation ability of liquid film. The wear mechanism of zinc phosphate impregnated graphite under oil lubrication conditions was dominated by abrasive wear and material removal was achieved through the fracture mechanism.


  • Open Access

    Inorganic nanomaterial lubricant additives for base fluids, to improve tribological performance: Recent developments

    by Junhai Wang, Weipeng Zhuang, Wenfeng Liang, Tingting Yan, Ting Li, Lixiu Zhang, Shu Li

    In this paper, we review recent research developments regarding the tribological performances of a series of inorganic nano-additives in lubricating fluids. First, we examine several basic types of inorganic nanomaterials, including metallic nanoparticles, metal oxides, carbon nanomaterials, and “other” nanomaterials. More specifically, the metallic nanoparticles we examine include silver, copper, nickel, molybdenum, and tungsten nanoparticles; the metal oxides include CuO, ZnO, Fe3O4, TiO2, ZrO2, Al2O3, and several double-metal oxides; the carbon nanomaterials include fullerene, carbon quantum dots, carbon nanotubes, graphene, graphene oxides, graphite, and diamond; and the “other” nanomaterials include metal sulfides, rare-earth compounds, layered double hydroxides, clay minerals, hexagonal boron nitride, black phosphorus, and nanocomposites. Second, we summarize the lubrication mechanisms of these nano-additives and identify the factors affecting their tribological performance. Finally, we briefly discuss the challenges faced by inorganic nanoparticles in lubrication applications and discuss future research directions. This review offers new perspectives to improve our understanding of inorganic nano-additives in tribology, as well as several new approaches to expand their practical applications.


  • System Deformation Behavior of Friction Pair in Fretting Wear

    by Jianfei Wang, Weihai Xue, Siyang Gao, Bi Wu, Shu Li, Deli Duan

    Several criteria for fretting wear behavior evaluation have been established since the proposal and establishment of the fretting loop concept. In this article, system deformation and system deformation ratio were defined. In addition, the fretting running conditions were distinguished from the evolution of system deformation with fretting cycles during fretting wear tests under different applied displacements and loads. In the gross slip regime, the system deformation was independent of the applied displacement and increased as the load increased, whereas in the partial slip regime, the system deformation was independent of the load and increased with the applied displacement. Furthermore, a linear relationship between the system deformation and the applied load in gross slip regime was found for the first time. Based on this linear relationship, the system deformation ratio can forecast the running regime with a given load and displacement. For the titanium alloy fretting pairs studied in this article, the fretting wear was found to run in the gross slip regime if the system deformation ratio was smaller than 0.9. Based on these observations, the system deformation ratio exhibited applicability in assisting the mechanical design of equipment suffering from fretting wear.


  • Open Access

    Tribological behaviors of turbofan seal couples from friction heat perspective under high-speed rubbing condition

    by Siyang Gao, Weihai Xue, Deli Duan, Shu Li

    The tribological behaviors of two types of seal coatings, nickel–graphite and aluminum–hexagon-boron nitride (Ni–Cg and Al–hBN, respectively) versus a Ti–6Al–4V blade used in turbofan engines were investigated using a high-speed rubbing test. The wear status and damage mechanism of the friction couples were studied and the abradability of the seal coatings was evaluated. By analysis of the coating properties and damage mechanism of the seal couple, the friction heat effect was identified as the key factor influencing blade wear forms as well as coating abradability. A one-dimensional heat conduction model was established to estimate the effect of increasing temperature on the friction interface. The results indicated that in the Ni–Cg and Ti–6Al–4V seal couple, the temperature rising rate (TRR) of the Ti–6Al–4V blade was faster than that of the Ni–Cg coating, and so the Ti–6Al–4V blade softened earlier than the Ni–Cg coating, causing the blade to suffer severe wear. In the Al–hBN and Ti–6Al–4V seal couple, the TRR of the Ti–6Al–4V blade was slower than that of the Al–hBN coating, and so the Al–hBN coating softened first; thus, blade damage was reduced or even replaced by coating adhesion. The square root ratio of thermal diffusivity between the blade and the coating could be taken as an indicator of the ratio of TRR between the blade and coating to predict blade wear status as well as damage mechanism. The results of the model agreed well with the experiment results of the two seal couples used in this study.


  • Exploration on tribological behaviours of perrhenates as potential lubricating oil additive during a wide temperature range

    by Junhai Wang, Yang Liu, Deli Duan, Shu Li

    The perrhenates of calcium, copper and lead used as oil additive were synthesised by using the aqueous solution method. The tribological properties of these perrhenates were examined by using a ball‐on‐disc tribotester during a wide temperature range and a four‐ball testing machine at room temperature. The four‐ball test results showed that all synthesised perrhenates presented good extreme pressure property to a certain degree and demonstrated satisfactory wear resistance at room temperature. The ball‐on‐disc experiment results showed that the base oil with perrhenate additives significantly decreased friction and wear compared with pure base oil at elevated temperatures. An antifriction and low‐shear layer was verified to form on sample surface after testing under high temperature. This layer effectively prevented the direct contact of sliding surfaces and decreased the friction coefficient. The antifriction behaviour of perrhenates implied that they could be developed as the candidate of oil additives for a hybrid lubricating mode. Copyright © 2015 John Wiley & Sons, Ltd.


  • Anti-friction Behavior of Lead Perrhenate in a Broad Temperature Range

    by Lin-Lin Liu, Shu Li, Yang Liu

    Extensive research efforts have been devoted to develop a new substance which could achieve effective lubrication in a broad temperature range. Pb(ReO4)2, composed of the double oxides of PbO and Re2O7, exists in low shear strength. The anti-friction behavior of Pb(ReO4)2 was tested by Universal Micro-Tribotester (UMT-2M) with ball (Si3N4) on disc (superalloy) at elevated and declined temperature in the range of 22¡䟴o 600¡䬠Composition of debris and morphologies of worn tracks were determined by X-ray diffraction (XRD) and scanning electron microscope (SEM), and contact resistance between the worn surface and steel ball was measured by UMT. The results show that Pb(ReO4)2 is a superior lubricant at elevated and declined temperatures, and the friction coefficient is much lower than that without lubricant. The superior lubricating properties should be attributed to the formation of an anti-frictional surface film. And higher temperature could result in the formation of a more complete and durable film. For Pb(ReO4)2 melts at 566¡䪠the fused product is much easier to flow and generate a film which could separate the tribo-pairs perfectly. Subsequently, the lowest friction coefficient is gained at 600¡䪠and good lubrication can be maintained till to 22¡