Mohammad Reza Sohrabi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mohammad Reza Sohrabi has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Sadegh Etedali
Department of Civil Engineering, Birjand University of Technology, P.O. Box 97175-569, Birjand, Iran
2 shared publications - Seyed Roohollah Mousavi
Civil Engineering Department, University of Sistan and Baluchestan, Zahedan, Iran
2 shared publications - Yaser Moodi
Civil Engineering Department, University of Sistan and Baluchestan, Zahedan, Iran
2 shared publications Ahmad Reza Abbasian
Department of Civil Engineering, University of Sistan and Baluchestan, Zahedan, Iran
1 shared publication- Ebrahim Gholamhosseini
Civil Engineering Department, University of Sistan and Baluchestan, Zahedan, Iran
1 shared publication - Ehsan Adili
Department of Civil Engineering, University of Sistan and Baluchestan, Zahedan, Iran
1 shared publication
Latest Publications
- Open Access
- 2 September 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Data-driven modeling and optimization of nano-belite cementitious composites incorporating internal NaCl and Na2SO4 additives
- 2 September 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Open AccessData-driven modeling and optimization of nano-belite cementitious composites incorporating internal NaCl and Na2SO4 additives
- Open Access
- 1 January 2024
- Published by Wiley in Shock and Vibration
- Vol. 2024 (1)
Experimental and Numerical Analysis of Omnidirectional Steel Moment Connection With Through‐Plate Panel Zone Under Cyclic Loading
This paper proposes a new beam to column connection, namely, the omnidirectional steel moment connection with through‐plate panel zone, which enables the connection of more than four beams to a column in moment frames at any arbitrary angle. The proposed connection was experimentally and numerically analyzed under cyclic loading. A numerical model using finite element method in ABAQUS is created and validated using hysteretic moment‐rotation curves. Subsequently, a sensitivity analysis is conducted on the key components of the proposed connection, including the connection panel zone, web plate, and bolts. The aim of this study is to optimize the design and configuration of the connection panel zone by simplifying it and removing the intersection of the through plates. Furthermore, the effect of changing the axial load of the column, removing the web plate, and altering the bolt size on the connection panel zone is investigated. The results of this sensitivity analysis demonstrate the efficiency and effectiveness of the proposed designs. The findings indicated that the experimental specimen showcased remarkable seismic compliance, adhering to AISC seismic provisions for special moment frames, even with minor buckling. It sustained a 0.04 radians drift without brittle fracture, aligning with expected mechanical behavior. The finite element‐based model revealed stress concentrations at beam‐to‐plate connections, and the average difference between the experimental and numerical model was 11.82%, verifying model accuracy. Hexagonal prism panels and internal through plates contribute minimally to parameter variations. In contrast, the web shear plate significantly affects the behavior. Bolt material substitution and axial loading introduce significant changes, while the combined effect of axial load and hexagonal prism panel removal shows distinctive alterations.
- 1 January 2024
- Published by Wiley in Shock and Vibration
- Vol. 2024 (1)
Open AccessExperimental and Numerical Analysis of Omnidirectional Steel Moment Connection With Through‐Plate Panel Zone Under Cyclic Loading
This paper proposes a new beam to column connection, namely, the omnidirectional steel moment connection with through‐plate panel zone, which enables the connection of more than four beams to a column in moment frames at any arbitrary angle. The proposed connection was experimentally and numerically analyzed under cyclic loading. A numerical model using finite element method in ABAQUS is created and validated using hysteretic moment‐rotation curves. Subsequently, a sensitivity analysis is conducted on the key components of the proposed connection, including the connection panel zone, web plate, and bolts. The aim of this study is to optimize the design and configuration of the connection panel zone by simplifying it and removing the intersection of the through plates. Furthermore, the effect of changing the axial load of the column, removing the web plate, and altering the bolt size on the connection panel zone is investigated. The results of this sensitivity analysis demonstrate the efficiency and effectiveness of the proposed designs. The findings indicated that the experimental specimen showcased remarkable seismic compliance, adhering to AISC seismic provisions for special moment frames, even with minor buckling. It sustained a 0.04 radians drift without brittle fracture, aligning with expected mechanical behavior. The finite element‐based model revealed stress concentrations at beam‐to‐plate connections, and the average difference between the experimental and numerical model was 11.82%, verifying model accuracy. Hexagonal prism panels and internal through plates contribute minimally to parameter variations. In contrast, the web shear plate significantly affects the behavior. Bolt material substitution and axial loading introduce significant changes, while the combined effect of axial load and hexagonal prism panel removal shows distinctive alterations.
- 31 January 2021
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Civil Engineering
- Vol. 46 (1) , 251-259
Strengthening of Lap-Spliced RC Beams Using Near-Surface Mounting Method
- 31 January 2021
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Civil Engineering
- Vol. 46 (1) , 251-259
Strengthening of Lap-Spliced RC Beams Using Near-Surface Mounting Method
- 1 December 2016
- Published by American Society of Civil Engineers (ASCE) in ASCE-ASME Journal of Risk and Uncertainty in Engineering Systems, Part A: Civil Engineering
- Vol. 2 (4)
Probabilistic Model for Bed-Joint Shear-Sliding Strength of Clay-Brick Walls Based on Field Test Data
Clay-brick unreinforced masonry is a very common practice in construction in many parts of the world. In this type of construction, earthquake-induced lateral loads are mainly absorbed by in-plane shear action of brick walls. Because of many inherent uncertainties, shear strength of brick walls is not a deterministic number. The fluctuating nature of the shear resistance can have a significant impact on the seismic performance of unreinforced masonry buildings. Therefore, the probabilistic features of shear-brick walls need to be investigated. ASTM C1531 is a standard test method for in situ measurement of masonry mortar joint shear strength. The test result would be an index of the wall’s shear capacity. In the present study, thousands of the aforementioned field test data are collected and analyzed not only to show the variable nature of wall shear strength, but also to derive the probabilistic characteristics of the parameter. These include mean, variance, standard error, and so on. However, th...
- 1 December 2016
- Published by American Society of Civil Engineers (ASCE) in ASCE-ASME Journal of Risk and Uncertainty in Engineering Systems, Part A: Civil Engineering
- Vol. 2 (4)
Probabilistic Model for Bed-Joint Shear-Sliding Strength of Clay-Brick Walls Based on Field Test Data
Clay-brick unreinforced masonry is a very common practice in construction in many parts of the world. In this type of construction, earthquake-induced lateral loads are mainly absorbed by in-plane shear action of brick walls. Because of many inherent uncertainties, shear strength of brick walls is not a deterministic number. The fluctuating nature of the shear resistance can have a significant impact on the seismic performance of unreinforced masonry buildings. Therefore, the probabilistic features of shear-brick walls need to be investigated. ASTM C1531 is a standard test method for in situ measurement of masonry mortar joint shear strength. The test result would be an index of the wall’s shear capacity. In the present study, thousands of the aforementioned field test data are collected and analyzed not only to show the variable nature of wall shear strength, but also to derive the probabilistic characteristics of the parameter. These include mean, variance, standard error, and so on. However, th...
- 25 May 2016
- Published by Techno-Press in Earthquakes and Structures
- Vol. 10 (5) , 1067-1087
Design of a decoupled PID controller via MOCS for seismic control of smart structures
- 25 May 2016
- Published by Techno-Press in Earthquakes and Structures
- Vol. 10 (5) , 1067-1087
Design of a decoupled PID controller via MOCS for seismic control of smart structures
- Open Access
- 1 March 2016
- Published by Elsevier in KSCE Journal of Civil Engineering
- Vol. 20 (2) , 768-776
A proposed approach to mitigate the torsional amplifications of asymmetric base-isolated buildings during earthquakes
- 1 March 2016
- Published by Elsevier in KSCE Journal of Civil Engineering
- Vol. 20 (2) , 768-776
Open AccessA proposed approach to mitigate the torsional amplifications of asymmetric base-isolated buildings during earthquakes
- Open Access
- 24 March 2015
- Published by Science Publishing Group in American Journal of Civil Engineering
- Vol. 3 (2) , 38-43
Reviewing the FRP Strengthening Systems
Several methods have been invented for flexural strengthening of RC beams using the FRP materials in recent years. These techniques are categorized into two main groups: Externally Bonded Reinforcement (EBR) techniques and Near Surface Mounted (NSM) techniques. The EBR family contains EBR (with conventional surface preparation), EBROG, EBRIG, MF-EBR, HOLING methods. The NSM family contains NSM-FRP Rods, NSM-FRP Sheets, NSM-MMFRP Rods methods. The EBR family techniques Despite the ease of implementation have weaknesses such as vulnerability against sever environmental conditions. Although the NSM techniques, have longer installation time than the EBR family techniques but in these methods the strengthening materials are greatly protected against the environmental effects. In this paper, the various techniques for flexural strengthening of RC members from both the EBR and NSM families have been fully described and advantages and disadvantages of each technique have been discussed.
- 24 March 2015
- Published by Science Publishing Group in American Journal of Civil Engineering
- Vol. 3 (2) , 38-43
Open AccessReviewing the FRP Strengthening Systems
Several methods have been invented for flexural strengthening of RC beams using the FRP materials in recent years. These techniques are categorized into two main groups: Externally Bonded Reinforcement (EBR) techniques and Near Surface Mounted (NSM) techniques. The EBR family contains EBR (with conventional surface preparation), EBROG, EBRIG, MF-EBR, HOLING methods. The NSM family contains NSM-FRP Rods, NSM-FRP Sheets, NSM-MMFRP Rods methods. The EBR family techniques Despite the ease of implementation have weaknesses such as vulnerability against sever environmental conditions. Although the NSM techniques, have longer installation time than the EBR family techniques but in these methods the strengthening materials are greatly protected against the environmental effects. In this paper, the various techniques for flexural strengthening of RC members from both the EBR and NSM families have been fully described and advantages and disadvantages of each technique have been discussed.
- 1 January 2014
- Published by SAGE Publications in Journal of Intelligent & Fuzzy Systems: Applications in Engineering and Technology
- Vol. 27 (3) , 1161-1168
Prediction of microcracks in concrete using fuzzy systems
This paper presents a fuzzy based assessment system which estimates the diameter of micro cracks in concrete. The most important micro cracks in concrete are ITZ cracks. Interfacial Transition Zone (ITZ) in concrete involves an approximately 30μm zone around each aggregate, within which the porosity increases as the aggregate interface is approached. The ITZ micro cracking of concrete was investigated experimentally by means of compressive stress testing and microscopic analysis. For imaging the ITZ micro cracks, Secondary Electron signals of SEM have been used. To define the membership functions, large numbers of concrete specimens were made and their ITZ crack width was imaged and measured by SEM. W/C ratio, amount of nano-sio 2 , micro sio 2 and age of specimens were considered as input membership functions and ITZ micro crack width was considered as output function. After the formation of black box and defuzzification, the system could predict the micro crack width correctly. Finally some random specimens were made to check the system prediction which showed suitable confirmation.
- 1 January 2014
- Published by SAGE Publications in Journal of Intelligent & Fuzzy Systems: Applications in Engineering and Technology
- Vol. 27 (3) , 1161-1168
Prediction of microcracks in concrete using fuzzy systems
This paper presents a fuzzy based assessment system which estimates the diameter of micro cracks in concrete. The most important micro cracks in concrete are ITZ cracks. Interfacial Transition Zone (ITZ) in concrete involves an approximately 30μm zone around each aggregate, within which the porosity increases as the aggregate interface is approached. The ITZ micro cracking of concrete was investigated experimentally by means of compressive stress testing and microscopic analysis. For imaging the ITZ micro cracks, Secondary Electron signals of SEM have been used. To define the membership functions, large numbers of concrete specimens were made and their ITZ crack width was imaged and measured by SEM. W/C ratio, amount of nano-sio 2 , micro sio 2 and age of specimens were considered as input membership functions and ITZ micro crack width was considered as output function. After the formation of black box and defuzzification, the system could predict the micro crack width correctly. Finally some random specimens were made to check the system prediction which showed suitable confirmation.