Adam F. Holt
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Adam F. Holt has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
B. A. Buffett
Department of Earth and Planetary Science, University of California, Berkeley, CA 94720, USA
1 shared publicationBruce A. Buffett
Department of Earth and Planetary Science University of California Berkeley California USA
1 shared publicationT. W. Becker
Department of Earth Sciences, University of Southern California, 3651 Trousdale Parkway, Los Angeles, CA 90089, USA
1 shared publicationThorsten W. Becker
Department of Earth Sciences University of Southern California Los Angeles California USA
1 shared publication
Latest Publications
- Open Access
- 6 May 2015
- Published by American Geophysical Union (AGU) in Geophysical Research Letters
- Vol. 42 (10) , 3802-3810
Overriding plate thickness control on subducting plate curvature
Subducting plate (SP) curvature exerts a key control on the amount of bending dissipation associated with subduction, and the magnitude of the subduction‐resisting bending force. However, the factors controlling the development of SP curvature are not well understood. We use numerical models to quantify the role of SP rheology on the minimum radius of curvature, Rmin. We find that Rmin depends strongly on the SP thickness when the rheology is viscous. This dependence is substantially reduced when the SP behaves plastically, in line with the lack of correlation between Rmin and SP thickness on Earth. In contrast, plasticity leads to a strong positive correlation between Rmin and the overriding plate (OP) thickness. Using an analysis of Rmin versus OP thickness, we show that such a positive correlation exists on Earth. This suggests that OP structure, in conjunction with SP plasticity, is crucial in generating slab curvature systematics on Earth.
- 6 May 2015
- Published by American Geophysical Union (AGU) in Geophysical Research Letters
- Vol. 42 (10) , 3802-3810
Open AccessOverriding plate thickness control on subducting plate curvature
Subducting plate (SP) curvature exerts a key control on the amount of bending dissipation associated with subduction, and the magnitude of the subduction‐resisting bending force. However, the factors controlling the development of SP curvature are not well understood. We use numerical models to quantify the role of SP rheology on the minimum radius of curvature, Rmin. We find that Rmin depends strongly on the SP thickness when the rheology is viscous. This dependence is substantially reduced when the SP behaves plastically, in line with the lack of correlation between Rmin and SP thickness on Earth. In contrast, plasticity leads to a strong positive correlation between Rmin and the overriding plate (OP) thickness. Using an analysis of Rmin versus OP thickness, we show that such a positive correlation exists on Earth. This suggests that OP structure, in conjunction with SP plasticity, is crucial in generating slab curvature systematics on Earth.
- 14 February 2015
- Published by Oxford University Press (OUP) in Geophysical Journal International
- Vol. 201 (1) , 172-192
Trench migration and overriding plate stress in dynamic subduction models
On Earth, oceanic plates subduct beneath a variety of overriding plate (OP) styles, from relatively thin and negatively buoyant oceanic OPs to thick and neutrally/positively buoyant continental OPs. The inclusion of an OP in numerical models of self-consistent subduction has been shown to reduce the rate that subducting slabs roll back relative to the equivalent single plate models. We use dynamic, 2-D subduction models to investigate how the mechanical properties, namely viscosity, thickness, and density, of the OP modify the slab rollback rate and the state of stress of the OP. In addition, we examine the role of the subducting plate (SP) viscosity. Because OP deformation accommodates the difference between the slab rollback rate and the far-field OP velocity, we find that the temporal variations in the rollback rate results in temporal variations in OP stress. The slabs in our models roll back rapidly until they reach the lower mantle viscosity increase, at which point the rollback velocity decreases. Concurrent with this reduction in rollback rate is a switch from an OP dominated by extensional stresses to a compressional OP. As in single plate models, the viscosity of the SP exerts a strong control on subducting slab kinematics; weaker slabs exhibit elevated sinking velocities and rollback rates. The SP viscosity also exerts a strong control on the OP stress regime. Weak slabs, either due to reduced bulk viscosity or stress-dependent weakening, have compressional OPs, while strong slabs have dominantly extensional OPs. While varying the viscosity of the OP alone does not substantially affect the OP stress state, we find that the OP thickness and buoyancy plays a substantial role in dictating the rate of slab rollback and OP stress state. Models with thick and/or negatively buoyant OPs have reduced rollback rates, and increased slab dip angles, relative to slabs with thin and/or positively buoyant OPs. Such elevated trench rollback for models with positively buoyant OPs induces extensional stresses in the OP, while OPs that are strongly negatively buoyant are under compression. While rollback is driven by the negative buoyancy of the subducting slab in such models of free subduction, we conclude that the physical properties of the OP potentially play a significant role in modulating both rollback rates and OP deformation style on Earth.
- 14 February 2015
- Published by Oxford University Press (OUP) in Geophysical Journal International
- Vol. 201 (1) , 172-192
Trench migration and overriding plate stress in dynamic subduction models
On Earth, oceanic plates subduct beneath a variety of overriding plate (OP) styles, from relatively thin and negatively buoyant oceanic OPs to thick and neutrally/positively buoyant continental OPs. The inclusion of an OP in numerical models of self-consistent subduction has been shown to reduce the rate that subducting slabs roll back relative to the equivalent single plate models. We use dynamic, 2-D subduction models to investigate how the mechanical properties, namely viscosity, thickness, and density, of the OP modify the slab rollback rate and the state of stress of the OP. In addition, we examine the role of the subducting plate (SP) viscosity. Because OP deformation accommodates the difference between the slab rollback rate and the far-field OP velocity, we find that the temporal variations in the rollback rate results in temporal variations in OP stress. The slabs in our models roll back rapidly until they reach the lower mantle viscosity increase, at which point the rollback velocity decreases. Concurrent with this reduction in rollback rate is a switch from an OP dominated by extensional stresses to a compressional OP. As in single plate models, the viscosity of the SP exerts a strong control on subducting slab kinematics; weaker slabs exhibit elevated sinking velocities and rollback rates. The SP viscosity also exerts a strong control on the OP stress regime. Weak slabs, either due to reduced bulk viscosity or stress-dependent weakening, have compressional OPs, while strong slabs have dominantly extensional OPs. While varying the viscosity of the OP alone does not substantially affect the OP stress state, we find that the OP thickness and buoyancy plays a substantial role in dictating the rate of slab rollback and OP stress state. Models with thick and/or negatively buoyant OPs have reduced rollback rates, and increased slab dip angles, relative to slabs with thin and/or positively buoyant OPs. Such elevated trench rollback for models with positively buoyant OPs induces extensional stresses in the OP, while OPs that are strongly negatively buoyant are under compression. While rollback is driven by the negative buoyancy of the subducting slab in such models of free subduction, we conclude that the physical properties of the OP potentially play a significant role in modulating both rollback rates and OP deformation style on Earth.