Dariusz Mika
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Dariusz Mika has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Jerzy Józwik
Department of Production Engineering, Lublin University of Technology, Lublin, Poland
10 shared publications - Alessandro Ruggiero
University of Salerno
3 shared publications - Fabio Leccese
Roma Tre University
2 shared publications - Andriy Holovatyy
Department of Computer-Aided Design Systems, Lviv Polytechnic National University, 79013 Lviv, Ukraine
1 shared publication Andrzej Krawczyk
Częstochowa University of Technology, Faculty of Electrical Engineering, Institute of Industrial Electrical Engineering 42-201 Częstochowa, Poland
1 shared publication- Farah Syazwani Shahar
Department of Aerospace Engineering, Faculty of Engineering, Universiti Putra Malaysia, Serdang 43400, Selangor, Malaysia
1 shared publication
Latest Publications
- Open Access
Vibration-Based Diagnostics of Rolling Element Bearings Using the Independent Component Analysis (ICA) Method
This manuscript presents a study on the application of blind source separation (BSS) techniques, specifically the Independent Component Analysis (ICA) method, for the detection and identification of localized faults in rolling element bearings. Bearing defects typically manifest as distinct harmonics of characteristic fault frequencies, accompanied by modulation sidebands in the vibration signal spectrum. The accurate extraction and isolation of these components are crucial for reliable fault diagnosis, particularly in systems where multiple vibration sources overlap. In this work, a linear ICA algorithm was applied to vibration signals acquired from a simplified rotating machinery setup designed to emulate common bearing fault conditions. The study investigates the effect of ICA-based signal decomposition on the statistical distribution of selected diagnostic indicators and evaluates its ability to enhance the detectability of fault-related components. The experimental results demonstrate that the application of ICA significantly improves the separation of vibration sources, leading to a more distinct representation of fault signatures. The findings confirm the effectiveness of blind source separation methods in vibration-based diagnostics and highlight the potential of ICA as a complementary tool for improving the accuracy and robustness of bearing fault detection systems in rotating machinery.
Open AccessVibration-Based Diagnostics of Rolling Element Bearings Using the Independent Component Analysis (ICA) Method
This manuscript presents a study on the application of blind source separation (BSS) techniques, specifically the Independent Component Analysis (ICA) method, for the detection and identification of localized faults in rolling element bearings. Bearing defects typically manifest as distinct harmonics of characteristic fault frequencies, accompanied by modulation sidebands in the vibration signal spectrum. The accurate extraction and isolation of these components are crucial for reliable fault diagnosis, particularly in systems where multiple vibration sources overlap. In this work, a linear ICA algorithm was applied to vibration signals acquired from a simplified rotating machinery setup designed to emulate common bearing fault conditions. The study investigates the effect of ICA-based signal decomposition on the statistical distribution of selected diagnostic indicators and evaluates its ability to enhance the detectability of fault-related components. The experimental results demonstrate that the application of ICA significantly improves the separation of vibration sources, leading to a more distinct representation of fault signatures. The findings confirm the effectiveness of blind source separation methods in vibration-based diagnostics and highlight the potential of ICA as a complementary tool for improving the accuracy and robustness of bearing fault detection systems in rotating machinery.
- Open Access
- 1 March 2025
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 19 (3) , 350-361
Fast approximation of matrix exponential and its application to independent component analysis problem
This paper introduces a new low-computational method for approximating the skew-symmetric and skew-Hermitian matrix exponential. Our method belongs to the splitting methods, which we modify and combine with new low-cost analytic formula for sparse skew-symmetric and skew-Hermitian...
- 1 March 2025
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 19 (3) , 350-361
Open AccessFast approximation of matrix exponential and its application to independent component analysis problem
This paper introduces a new low-computational method for approximating the skew-symmetric and skew-Hermitian matrix exponential. Our method belongs to the splitting methods, which we modify and combine with new low-cost analytic formula for sparse skew-symmetric and skew-Hermitian...
- Open Access
- 13 September 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (18) , 8265
Azimuthal Solar Synchronization and Aerodynamic Neuro-Optimization: An Empirical Study on Slime-Mold-Inspired Neural Networks for Solar UAV Range Optimization
This study introduces a novel methodology for enhancing the efficiency of solar-powered unmanned aerial vehicles (UAVs) through azimuthal solar synchronization and aerodynamic neuro-optimization, leveraging the principles of slime mold neural networks. The objective is to broaden the operational capabilities of solar UAVs, enabling them to perform over extended ranges and in varied weather conditions. Our approach integrates a computational model of slime mold networks with a simulation environment to optimize both the solar energy collection and the aerodynamic performance of UAVs. Specifically, we focus on improving the UAVs’ aerodynamic efficiency in flight, aligning it with energy optimization strategies to ensure sustained operation. The findings demonstrated significant improvements in the UAVs’ range and weather resilience, thereby enhancing their utility for a variety of missions, including environmental monitoring and search and rescue operations. These advancements underscore the potential of integrating biomimicry and neural-network-based optimization in expanding the functional scope of solar UAVs.
- 13 September 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (18) , 8265
Open AccessAzimuthal Solar Synchronization and Aerodynamic Neuro-Optimization: An Empirical Study on Slime-Mold-Inspired Neural Networks for Solar UAV Range Optimization
This study introduces a novel methodology for enhancing the efficiency of solar-powered unmanned aerial vehicles (UAVs) through azimuthal solar synchronization and aerodynamic neuro-optimization, leveraging the principles of slime mold neural networks. The objective is to broaden the operational capabilities of solar UAVs, enabling them to perform over extended ranges and in varied weather conditions. Our approach integrates a computational model of slime mold networks with a simulation environment to optimize both the solar energy collection and the aerodynamic performance of UAVs. Specifically, we focus on improving the UAVs’ aerodynamic efficiency in flight, aligning it with energy optimization strategies to ensure sustained operation. The findings demonstrated significant improvements in the UAVs’ range and weather resilience, thereby enhancing their utility for a variety of missions, including environmental monitoring and search and rescue operations. These advancements underscore the potential of integrating biomimicry and neural-network-based optimization in expanding the functional scope of solar UAVs.
- Open Access
Incomplete Cross Splitting in the Approximation of Skew-Symmetric Matrix Exponential
This paper proposes a new splitting method for approximating the exponential of skew-symmetric and skew-Hermitian matrix A . Our point of departure is the splitting methods for approximation of the matrix exponential, which we modify and combine with new low-cost analytic formula for some sparse matrix exponential. Our motivation is to create and test a fast exponential approximation method in the context of a balance between speed and quality of approximation. We propose a cross splitting of the matrix A and use it in incomplete form for reducing computational complexity of exponential stage. We have also derived an analytical formula for a cross-type sparse skew-symmetric and skew-Hermitian matrix exponential, similar to the Euler-Rodrigues relation, well known for skew-symmetric matrices in R 3 . We evaluate this approximation problem in the context of computational cost and the speed of the algorithms used in technology. A number of numerical experiments conclude the optimization problem of the Independent Components Analysis type, the results of which confirm the effectiveness of the proposed method in technical applications.
Open AccessIncomplete Cross Splitting in the Approximation of Skew-Symmetric Matrix Exponential
This paper proposes a new splitting method for approximating the exponential of skew-symmetric and skew-Hermitian matrix A . Our point of departure is the splitting methods for approximation of the matrix exponential, which we modify and combine with new low-cost analytic formula for some sparse matrix exponential. Our motivation is to create and test a fast exponential approximation method in the context of a balance between speed and quality of approximation. We propose a cross splitting of the matrix A and use it in incomplete form for reducing computational complexity of exponential stage. We have also derived an analytical formula for a cross-type sparse skew-symmetric and skew-Hermitian matrix exponential, similar to the Euler-Rodrigues relation, well known for skew-symmetric matrices in R 3 . We evaluate this approximation problem in the context of computational cost and the speed of the algorithms used in technology. A number of numerical experiments conclude the optimization problem of the Independent Components Analysis type, the results of which confirm the effectiveness of the proposed method in technical applications.
- Open Access
- 19 July 2023
- Published by Springer Nature in Scientific Reports
- Vol. 13 (1) , 1-16
Fast gradient algorithm for complex ICA and its application to the MIMO systems
This paper proposes a new gradient-descent algorithm for complex independent component analysis and presents its application to the Multiple-Input Multiple-Output communication systems. Algorithm uses the Lie structure of optimization landscape and toral decomposition of gradient matrix. The theoretical results are validated by computer simulation and compared to several classes of algorithms, gradient descent, quasi-Newton as well as complex JADE. The simulations performed showed excellent results of the algorithm in terms of speed, stability of operation and the quality of separation. A characteristic feature of gradient methods is their quick response to changes in the input signal. The good results of the proposed algorithm indicate potential use in on-line applications.
- 19 July 2023
- Published by Springer Nature in Scientific Reports
- Vol. 13 (1) , 1-16
Open AccessFast gradient algorithm for complex ICA and its application to the MIMO systems
This paper proposes a new gradient-descent algorithm for complex independent component analysis and presents its application to the Multiple-Input Multiple-Output communication systems. Algorithm uses the Lie structure of optimization landscape and toral decomposition of gradient matrix. The theoretical results are validated by computer simulation and compared to several classes of algorithms, gradient descent, quasi-Newton as well as complex JADE. The simulations performed showed excellent results of the algorithm in terms of speed, stability of operation and the quality of separation. A characteristic feature of gradient methods is their quick response to changes in the input signal. The good results of the proposed algorithm indicate potential use in on-line applications.
- Open Access
Cutting Force during Surface Layer Milling of Selected Aluminium Alloys
This paper presents the analysis of cutting force during surface layer milling of selected aluminium alloys, which are widely used in the aviation industry. The cutting force is one of the most important parameters determining the machinability of the material and also provides important information about the course of the cutting. The study analysed the influence of the technological parameters, i.e., cutting speed vc and depth of cut ap as well as the relation between cutting tool feed direction and rolling direction on the value of cutting force during milling of selected aluminium alloys, i.e., EN AW-2017A T451 and EN AW-2024 T351. The material anisotropy is a very important issue, since the engineering industry faces enormous problems related to the cutting of the tested materials that are usually supplied in the form of rolled plates. The surface layer was cut due to the fact that it accumulates the greatest residual stresses. The measurement process of cutting force was performed by using 9257B Kistler piezoelectric dynamometer. As part of the analysis of the results, the measurement uncertainty was also estimated, which was determined on the basis of two components obtained by using the A and B methods, respectively.
Open AccessCutting Force during Surface Layer Milling of Selected Aluminium Alloys
This paper presents the analysis of cutting force during surface layer milling of selected aluminium alloys, which are widely used in the aviation industry. The cutting force is one of the most important parameters determining the machinability of the material and also provides important information about the course of the cutting. The study analysed the influence of the technological parameters, i.e., cutting speed vc and depth of cut ap as well as the relation between cutting tool feed direction and rolling direction on the value of cutting force during milling of selected aluminium alloys, i.e., EN AW-2017A T451 and EN AW-2024 T351. The material anisotropy is a very important issue, since the engineering industry faces enormous problems related to the cutting of the tested materials that are usually supplied in the form of rolled plates. The surface layer was cut due to the fact that it accumulates the greatest residual stresses. The measurement process of cutting force was performed by using 9257B Kistler piezoelectric dynamometer. As part of the analysis of the results, the measurement uncertainty was also estimated, which was determined on the basis of two components obtained by using the A and B methods, respectively.
- Open Access
Single Channel Source Separation with ICA-Based Time-Frequency Decomposition
This paper relates to the separation of single channel source signals from a single mixed signal by means of independent component analysis (ICA). The proposed idea lies in a time-frequency representation of the mixed signal and the use of ICA on spectral rows corresponding to different time intervals. In our approach, in order to reconstruct true sources, we proposed a novelty idea of grouping statistically independent time-frequency domain (TFD) components of the mixed signal obtained by ICA. The TFD components are grouped by hierarchical clustering and k-mean partitional clustering. The distance between TFD components is measured with the classical Euclidean distance and the distance of Gaussian distribution introduced by as. In addition, the TFD components are grouped by minimizing the negentropy of reconstructed constituent signals. The proposed method was used to separate source signals from single audio mixes of two- and three-component signals. The separation was performed using algorithms written by the authors in Matlab. The quality of obtained separation results was evaluated by perceptual tests. The tests showed that the automated separation requires qualitative information about time-frequency characteristics of constituent signals. The best separation results were obtained with the use of the distance of Gaussian distribution, a distance measure based on the knowledge of the statistical nature of spectra of original constituent signals of the mixed signal.Open AccessSingle Channel Source Separation with ICA-Based Time-Frequency Decomposition
This paper relates to the separation of single channel source signals from a single mixed signal by means of independent component analysis (ICA). The proposed idea lies in a time-frequency representation of the mixed signal and the use of ICA on spectral rows corresponding to different time intervals. In our approach, in order to reconstruct true sources, we proposed a novelty idea of grouping statistically independent time-frequency domain (TFD) components of the mixed signal obtained by ICA. The TFD components are grouped by hierarchical clustering and k-mean partitional clustering. The distance between TFD components is measured with the classical Euclidean distance and the distance of Gaussian distribution introduced by as. In addition, the TFD components are grouped by minimizing the negentropy of reconstructed constituent signals. The proposed method was used to separate source signals from single audio mixes of two- and three-component signals. The separation was performed using algorithms written by the authors in Matlab. The quality of obtained separation results was evaluated by perceptual tests. The tests showed that the automated separation requires qualitative information about time-frequency characteristics of constituent signals. The best separation results were obtained with the use of the distance of Gaussian distribution, a distance measure based on the knowledge of the statistical nature of spectra of original constituent signals of the mixed signal. - Open Access
Lie Group Methods in Blind Signal Processing
This paper deals with the use of Lie group methods to solve optimization problems in blind signal processing (BSP), including Independent Component Analysis (ICA) and Independent Subspace Analysis (ISA). The paper presents the theoretical fundamentals of Lie groups and Lie algebra, the geometry of problems in BSP as well as the basic ideas of optimization techniques based on Lie groups. Optimization algorithms based on the properties of Lie groups are characterized by the fact that during optimization motion, they ensure permanent bonding with a search space. This property is extremely significant in terms of the stability and dynamics of optimization algorithms. The specific geometry of problems such as ICA and ISA along with the search space homogeneity enable the use of optimization techniques based on the properties of the Lie groups and . An interesting idea is that of optimization motion in one-parameter commutative subalgebras and toral subalgebras that ensure low computational complexity and high-speed algorithms.Open AccessLie Group Methods in Blind Signal Processing
This paper deals with the use of Lie group methods to solve optimization problems in blind signal processing (BSP), including Independent Component Analysis (ICA) and Independent Subspace Analysis (ISA). The paper presents the theoretical fundamentals of Lie groups and Lie algebra, the geometry of problems in BSP as well as the basic ideas of optimization techniques based on Lie groups. Optimization algorithms based on the properties of Lie groups are characterized by the fact that during optimization motion, they ensure permanent bonding with a search space. This property is extremely significant in terms of the stability and dynamics of optimization algorithms. The specific geometry of problems such as ICA and ISA along with the search space homogeneity enable the use of optimization techniques based on the properties of the Lie groups and . An interesting idea is that of optimization motion in one-parameter commutative subalgebras and toral subalgebras that ensure low computational complexity and high-speed algorithms.