Najaf Ali
Najaf Ali has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
Khurram Shahzad
Univ Punjab, Inst Chem Engn & Technol, Lahore, Pakistan
4 shared publicationsArshad Chughtai
Institute of Chemical Engineering & Technology, University of the Punjab-Pakistan, Lahore, Pakistan
3 shared publicationsMahmood Saleem
Institute of Chemical Engineering & Technology, University of the Punjab-Pakistan, Lahore, Pakistan
3 shared publicationsHafiz Miqdad Masood
NFC Inst Engn & Fertilizer Res, Dept Chem Engn & Technol, Faisalabad, Pakistan
2 shared publicationsAhmad Naveed
NFC Inst Engn & Fertilizer Res, Dept Chem Engn & Technol, Faisalabad, Pakistan
1 shared publication- Keith R. Cliffe
Department of Mechanical and Process Engineering, University of Sheffield, Sheffield S10 2TN, UK
1 shared publication
Latest Publications
- 14 March 2023
- Published by Pakistan Institute of Chemical Engineers in Journal of the Pakistan Institute of Chemical Engineers
- Vol. 51 (1) , 1-10
Removal of heavy metals from wastewater of textile industry using polymeric nano-adsorbent
- 14 March 2023
- Published by Pakistan Institute of Chemical Engineers in Journal of the Pakistan Institute of Chemical Engineers
- Vol. 51 (1) , 1-10
Removal of heavy metals from wastewater of textile industry using polymeric nano-adsorbent
- 20 November 2019
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 46 (1) , 1-13
Fluidized bed fast pyrolysis of corn stover: Effects of fluidizing gas flow rate and composition
Fast pyrolysis of corn stover was carried out in a pilot scale fluidized bed reactor in nitrogen atmosphere. The effects of varying gas flow rates at optimum reaction temperature of about 500ºC and feed size of < 1.0 mm on yield and composition of bio-oil, char and gas were investigated. The results for three runs with flow rate of gas of 45, 80 and 70 L/min, respectively, were obtained. The distribution of pyrolysis products was calculated gravimetrically by mass balance and corrected with optimization mass model using proximate and ultimate analysis of feedstock and pyrolysis products. The maximum yield of bio-oil (52 wt%) was obtained in run 3 with flow rate of gas of 70 L/min having heating value of 21.20 MJ/kg. GC-MS analysis identified the major chemical compounds present in the bio-oil which were levoglucosan, hydroxyl acetaldehyde, acetol, acetic acid, phenols, 2-methyl-2-cylopenten-1-one, guaiacol, 2(5H)-furanone, fufuryl alcohol, p-cresol and 2-ethyl alcohol. The bio-oil produced from run 3 had higher amounts of aromatic hydrocarbons, non-methoxylated phenolics, levoglucosan and smaller amounts of acids. On the other hand, bio-oil obtained from TGRP experiments had low value of total acid number (57.73 mg of KOH/g) indicating less oxygenating compounds with greater heating value in the product.
- 20 November 2019
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 46 (1) , 1-13
Fluidized bed fast pyrolysis of corn stover: Effects of fluidizing gas flow rate and composition
Fast pyrolysis of corn stover was carried out in a pilot scale fluidized bed reactor in nitrogen atmosphere. The effects of varying gas flow rates at optimum reaction temperature of about 500ºC and feed size of < 1.0 mm on yield and composition of bio-oil, char and gas were investigated. The results for three runs with flow rate of gas of 45, 80 and 70 L/min, respectively, were obtained. The distribution of pyrolysis products was calculated gravimetrically by mass balance and corrected with optimization mass model using proximate and ultimate analysis of feedstock and pyrolysis products. The maximum yield of bio-oil (52 wt%) was obtained in run 3 with flow rate of gas of 70 L/min having heating value of 21.20 MJ/kg. GC-MS analysis identified the major chemical compounds present in the bio-oil which were levoglucosan, hydroxyl acetaldehyde, acetol, acetic acid, phenols, 2-methyl-2-cylopenten-1-one, guaiacol, 2(5H)-furanone, fufuryl alcohol, p-cresol and 2-ethyl alcohol. The bio-oil produced from run 3 had higher amounts of aromatic hydrocarbons, non-methoxylated phenolics, levoglucosan and smaller amounts of acids. On the other hand, bio-oil obtained from TGRP experiments had low value of total acid number (57.73 mg of KOH/g) indicating less oxygenating compounds with greater heating value in the product.
- 27 August 2019
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 44 (2) , 2938-2951
Slow pyrolysis of indigenous Makarwal coal: characterization, kinetic study, and calculation of design parameters
Pyrolysis is a common stage of many coal utilization processes such as carbonization, gasification, combustion, and liquefaction. Char is the main product from slow pyrolysis of coal. Proximate analysis of Makarwal coal sample has ash contents of 34.61% and heating rate of 12,300 Btu/lb. CHNS analysis yields the elemental carbon of 43.41 % and sulfur amount of 58.041% which can be removed by further treatment process. Thermo-gravimetric analysis (TGA) study of Makarwal coal sample recognized that maximum decomposition takes place at 441ºC. The rate of reaction, rate constant and activation energy estimated from the kinetic study of slow pyrolysis are 7.55*10−5 mol/cm3.s, 0.001135/s and 0.045 kj/mol, respectively. Experiments were performed at different coal particles with size ranging from 0.5 to 0.2 mm and heating rate of 9–15ºC/min at temperature range of 300–700ºC under inert N2 gas atmosphere. Char is the main product in this study which is maximum at 9ºC/min and temperature of 300ºC having conversion rate of 92%. The desired char products have 44.63% fixed carbon and HHV of 14,300 Btu/lb.
- 27 August 2019
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 44 (2) , 2938-2951
Slow pyrolysis of indigenous Makarwal coal: characterization, kinetic study, and calculation of design parameters
Pyrolysis is a common stage of many coal utilization processes such as carbonization, gasification, combustion, and liquefaction. Char is the main product from slow pyrolysis of coal. Proximate analysis of Makarwal coal sample has ash contents of 34.61% and heating rate of 12,300 Btu/lb. CHNS analysis yields the elemental carbon of 43.41 % and sulfur amount of 58.041% which can be removed by further treatment process. Thermo-gravimetric analysis (TGA) study of Makarwal coal sample recognized that maximum decomposition takes place at 441ºC. The rate of reaction, rate constant and activation energy estimated from the kinetic study of slow pyrolysis are 7.55*10−5 mol/cm3.s, 0.001135/s and 0.045 kj/mol, respectively. Experiments were performed at different coal particles with size ranging from 0.5 to 0.2 mm and heating rate of 9–15ºC/min at temperature range of 300–700ºC under inert N2 gas atmosphere. Char is the main product in this study which is maximum at 9ºC/min and temperature of 300ºC having conversion rate of 92%. The desired char products have 44.63% fixed carbon and HHV of 14,300 Btu/lb.
- Open Access
Development of a Temperature Programmed Identification Technique to Characterize the Organic Sulphur Functional Groups in Coal
The Temperature Programmed Reduction (TPR) technique is employed for the characterisation of various organic sulphur functional groups in coal. The TPR technique is modified into the Temperature Programmed Identification technique to investigate whether this method can detect various functional groups corresponding to their reduction temperatures. Ollerton, Harworth, Silverdale, Prince of Wales coal and Mequinenza lignite were chosen for this study. High pressure oxydesulphurisation of the coal samples was also done. The characterization of various organic sulphur functional groups present in untreated and treated coal by the TPR method and later by the TPI method confirmed that these methods can identify the organic sulphur groups in coal and that the results based on total sulphur are comparable with those provided by standard analytical techniques. The analysis of the untreated and treated coal samples showed that the structural changes in the organic sulphur matrix due to a reaction can be determined.
Open AccessDevelopment of a Temperature Programmed Identification Technique to Characterize the Organic Sulphur Functional Groups in Coal
The Temperature Programmed Reduction (TPR) technique is employed for the characterisation of various organic sulphur functional groups in coal. The TPR technique is modified into the Temperature Programmed Identification technique to investigate whether this method can detect various functional groups corresponding to their reduction temperatures. Ollerton, Harworth, Silverdale, Prince of Wales coal and Mequinenza lignite were chosen for this study. High pressure oxydesulphurisation of the coal samples was also done. The characterization of various organic sulphur functional groups present in untreated and treated coal by the TPR method and later by the TPI method confirmed that these methods can identify the organic sulphur groups in coal and that the results based on total sulphur are comparable with those provided by standard analytical techniques. The analysis of the untreated and treated coal samples showed that the structural changes in the organic sulphur matrix due to a reaction can be determined.
- Open Access
- 1 September 2016
- Published by Walter de Gruyter GmbH in Polish Journal of Chemical Technology
- Vol. 18 (3) , 88-96
Effect of operating parameters on production of bio-oil from fast pyrolysis of maize stalk in bubbling fluidized bed reactor
The yield and composition of pyrolysis products depend on the characteristics of feed stock and process operating parameters. Effect of particle size, reaction temperature and carrier gas flow rate on the yield of bio-oil from fast pyrolysis of Pakistani maize stalk was investigated. Pyrolysis experiments were performed at temperature range of 360-540°C, feed particle size of 1-2 mm and carrier gas fl ow rate of 7.0-13.0 m3/h (0.61.1 m/s superficial velocity). Bio-oil yield increased with the increase of temperature followed by a decreasing trend. The maximum yield of bio-oil obtained was 42 wt% at a temperature of 490°C with the particle size of around 1.0 mm and carrier gas flow rate of 11.0 m3/h (0.9 m/s superficial velocity). High temperatures resulted in the higher ratios of char and non-condensable gas.
- 1 September 2016
- Published by Walter de Gruyter GmbH in Polish Journal of Chemical Technology
- Vol. 18 (3) , 88-96
Open AccessEffect of operating parameters on production of bio-oil from fast pyrolysis of maize stalk in bubbling fluidized bed reactor
The yield and composition of pyrolysis products depend on the characteristics of feed stock and process operating parameters. Effect of particle size, reaction temperature and carrier gas flow rate on the yield of bio-oil from fast pyrolysis of Pakistani maize stalk was investigated. Pyrolysis experiments were performed at temperature range of 360-540°C, feed particle size of 1-2 mm and carrier gas fl ow rate of 7.0-13.0 m3/h (0.61.1 m/s superficial velocity). Bio-oil yield increased with the increase of temperature followed by a decreasing trend. The maximum yield of bio-oil obtained was 42 wt% at a temperature of 490°C with the particle size of around 1.0 mm and carrier gas flow rate of 11.0 m3/h (0.9 m/s superficial velocity). High temperatures resulted in the higher ratios of char and non-condensable gas.
- 5 August 2015
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 40 (11) , 3019-3027
Bio-Oil Production from Fast Pyrolysis of Cotton Stalk in Fluidized Bed Reactor
- 5 August 2015
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 40 (11) , 3019-3027
Bio-Oil Production from Fast Pyrolysis of Cotton Stalk in Fluidized Bed Reactor