TSThomas Sinn

Thomas Sinn

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Thomas Sinn has a total of 2 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Design, Manufacturing and Test of a High Lift Secondary Flight Control Surface with Shape Memory Alloy Post-Buckled Precompressed Actuators

    by Thomas Sinn, Ron Barrett

    The use of morphing components on aerospace structures can greatly increase the versatility of an aircraft. This paper presents the design, manufacturing and testing of a new kind of adaptive airfoil with actuation through Shape Memory Alloys (SMA). The developed adaptive flap system makes use of a novel actuator that employs SMA wires in an antagonistic arrangement with a Post-Buckled Precompressed (PBP) mechanism. SMA actuators are usually used in an antagonistic arrangement or are arranged to move structural components with linearly varying resistance levels similar to springs. Unfortunately, most of this strain energy is spent doing work on the passive structure rather than performing the task at hand, like moving a flight control surface or resisting air loads. A solution is the use of Post-Buckled Precompressed (PBP) actuators that are arranged so that the active elements do not waste energy fighting passive structural stiffnesses. One major problem with PBP actuators is that the low tensile strength of the piezoelectric elements can often result in tensile failure of the actuator on the convex face. A solution to this problem is the use of SMA as actuator material due to their tolerance of tensile stresses. The power consumption to hold deflections is reduced by approximately 20% with the Post-Buckled Precompressed mechanism. Conventional SMAs are essentially non-starters for many classes of aircraft due to the requirement of holding the flight control surfaces in a given position for extremely long times to trim the vehicle. For the reason that PBP actuators balance out air and structural loads, the steady-state load on the SMAs is essentially negligible, when properly designed. Simulations and experiments showed that the SMAPBP actuator shows tip rotations on the order of 45°, which is nearly triple the levels achieved by piezoelectric PBP actuators. The developed SMAPBP actuator was integrated in a NACA0012 airfoil with a flexible skin to carry out wind tunnel tests.


  • Open Access

    Design, Manufacturing and Test of a High Lift Secondary Flight Control Surface With SMAPBP (Shape Memory Alloy Post-Buckled Precompressed) Actuators

    by Thomas Sinn, Ron Barrett

    This paper discusses the design, manufacturing and test of a new kind of adaptive airfoil with Shape Memory Alloy actuation. An antagonistic arrangement of SMA wires is used in a Post-buckled Precompressed (PBP) kind of actuator that is being employed in an adaptive flap system. SMA actuators are typically used either antagonistically and/or arranged to move structural components with linearly varying resistance levels, like springs. This generally means that large percentages of strain energy are spent doing work on passive structure (rather than performing the task at hand, like moving a flight control surface or resisting air loads etc.). Post-Buckled Precompressed (PBP) actuators on the other hand are arranged so that the active elements do not waste energy fighting passive structural stiffnesses. Most (if not all) of the PBP actuators of the past have used piezoceramic elements and are highly prone to tensile failure on convex faces. Because SMA actuators are far more tolerant of tensile stresses than piezoceramics, a switch of actuator type is a natural progression of technology. With the Post-buckled Precompressed mechanism, the power consumption to hold deflections is reduced by one if not two orders of magnitude. Because aircraft often require flight control surfaces to be held in a given position for extremely long times to trim the vehicle, conventional SMA’s are essentially non-starters for many classes of aircraft. For the reason that PBP actuators balance out air and structural loads, the steady-state load on the SMAs is essentially negligible, when properly designed. Experiments showed that the SMAPBP actuator shows tip rotations on the order of 45° which is nearly triple the levels achieved by piezoelectric PBP actuators. The paper opens with a short survey on the history of flap systems actuated by adaptive materials and delves into actuation theory. In the following the author gives a detailed explanation of the design concept and the manufacturing of the airfoil. A NACA0012 airfoil with a chord length of 150 mm was used to prove the concept of the adaptive flap system. The paper continues with a description of the test setup, the CFD model assumptions and the results of wind tunnel tests. The architecture and the employment of a closed loop position feedback system to overcome the nonlinear behavior of the SMA material and the PBP mechanism is also discussed.