Hiroshi Ito
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hiroshi Ito has a total of 593 co-authors. Here are the top co-authors by number of shared publications:
- Takeshi Kikutani
School of Materials and Chemical Technology, Institute of Science Tokyo, Tokyo 152-8550, Japan
33 shared publications - Akira Ishigami
Graduate School of Organic Materials Science, Yamagata University, 4-3-16 Jonan, Yonezawa, Yamagata 992-8510, Japan
18 shared publications - Takashi Kurose
Research Center for GREEN Materials and Advanced Processing Yamagata University 4-3-16 Jonan Yonezawa Yamagata 992-8510 Japan
18 shared publications - Kentaro Taki
Department of Frontier Engineering, Kanazawa University, Kakuma-machi, Kanazawa, Ishikawa 920-1192, Japan
14 shared publications - Yuchen Mao
Research Center for GREEN Materials & Advanced Processing, Yamagata University, Yonezawa, Yamagata 992-8510, Japan
13 shared publications Tetsuo Takayama
Graduate School of Organic Materials Science Yamagata University 4‐3‐16 Jonan Yonezawa Yamagata 992‐8510 Japan
12 shared publications
Latest Publications
- Open Access
- 1 September 2026
- Published by Elsevier in SSRN Electronic Journal
UV-Stable Polyamide 6/Clay Nanocomposites with Enhanced Marine Biodegradation
Biodegradable plastics offer a promising strategy to mitigate mismanaged waste plastic pollution, yet balancing mechanical integrity during service with rapid post-disposal degradation remains challenging. This study reports a facile approach to fabricating polyamide 6/layered silicate nanocomposites (PA6/clay) that achieve an excellent balance between durability and environmental degradability. The resulting composites exhibit thermal properties comparable to those of neat PA6 while delivering significantly enhanced mechanical performance; specifically, the Young's modulus and yield strength increased by 139% and 31%, respectively, compared to neat PA6. Crucially, the PA6/clay composites exhibit superior photostability; even after extended UV exposure, they retain mechanical properties comparable to those of unexposed PA6 films. Furthermore, the incorporation of nanoclay enhances the marine biodegradability of the matrix, as demonstrated by the higher degree of biodegradation. Consequently, this work establishes a viable materials-design strategy for engineering polymers that maintain high weathering resistance during active use but undergo accelerated biodegradation upon disposal.
- 1 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessUV-Stable Polyamide 6/Clay Nanocomposites with Enhanced Marine Biodegradation
Biodegradable plastics offer a promising strategy to mitigate mismanaged waste plastic pollution, yet balancing mechanical integrity during service with rapid post-disposal degradation remains challenging. This study reports a facile approach to fabricating polyamide 6/layered silicate nanocomposites (PA6/clay) that achieve an excellent balance between durability and environmental degradability. The resulting composites exhibit thermal properties comparable to those of neat PA6 while delivering significantly enhanced mechanical performance; specifically, the Young's modulus and yield strength increased by 139% and 31%, respectively, compared to neat PA6. Crucially, the PA6/clay composites exhibit superior photostability; even after extended UV exposure, they retain mechanical properties comparable to those of unexposed PA6 films. Furthermore, the incorporation of nanoclay enhances the marine biodegradability of the matrix, as demonstrated by the higher degree of biodegradation. Consequently, this work establishes a viable materials-design strategy for engineering polymers that maintain high weathering resistance during active use but undergo accelerated biodegradation upon disposal.
- Open Access
- 22 August 2026
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 143 (42)
Mixing and Compounding of Graphene/High Density Polyethylene Nanocomposites Using Twin‐Screw and Octa‐Screw Extrusions: A Comparative Study
Multi‐screw extrusions are crucial for compounding polymeric nanocomposites. However, achieving homogeneous nanomaterial dispersion in high‐viscosity matrices without severe thermal degradation remains a significant challenge. This study presents a comparative investigation evaluating the compounding efficacy of conventional twin‐screw extruders (TSE) against a uniquely designed octa‐screw extruder (OSE) for graphene‐filled high‐density polyethylene (HDPE) nanocomposites. The structural, thermal, flow, and mechanical properties of 5.0 wt% graphene/HDPE nanocomposites were systematically assessed. Morphological results indicate that the OSE's unique multi‐stage intermeshing geometry yields a significantly more uniform graphene dispersion and effectively reduces agglomeration compared to the TSE. Benefiting from a narrower residence time distribution and lower processing temperature profile, the OSE minimized thermal degradation while allowing highly exfoliated graphene to act as nanoscale solid lubricants. Consequently, OSE‐compounded nanocomposites exhibited superior macroscopic properties over TSE counterparts, including enhanced crystallinity (63.3% vs. 62.1%), improved ultimate tensile strength (28.5 MPa vs. 27.5 MPa), higher decomposition temperature (461°C vs. 457°C), and better melt flowability. These findings demonstrate that octa‐screw extrusion provides a scalable processing advantage for developing advanced, high‐performance polymer nanocomposites.
- 22 August 2026
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 143 (42)
Open AccessMixing and Compounding of Graphene/High Density Polyethylene Nanocomposites Using Twin‐Screw and Octa‐Screw Extrusions: A Comparative Study
Multi‐screw extrusions are crucial for compounding polymeric nanocomposites. However, achieving homogeneous nanomaterial dispersion in high‐viscosity matrices without severe thermal degradation remains a significant challenge. This study presents a comparative investigation evaluating the compounding efficacy of conventional twin‐screw extruders (TSE) against a uniquely designed octa‐screw extruder (OSE) for graphene‐filled high‐density polyethylene (HDPE) nanocomposites. The structural, thermal, flow, and mechanical properties of 5.0 wt% graphene/HDPE nanocomposites were systematically assessed. Morphological results indicate that the OSE's unique multi‐stage intermeshing geometry yields a significantly more uniform graphene dispersion and effectively reduces agglomeration compared to the TSE. Benefiting from a narrower residence time distribution and lower processing temperature profile, the OSE minimized thermal degradation while allowing highly exfoliated graphene to act as nanoscale solid lubricants. Consequently, OSE‐compounded nanocomposites exhibited superior macroscopic properties over TSE counterparts, including enhanced crystallinity (63.3% vs. 62.1%), improved ultimate tensile strength (28.5 MPa vs. 27.5 MPa), higher decomposition temperature (461°C vs. 457°C), and better melt flowability. These findings demonstrate that octa‐screw extrusion provides a scalable processing advantage for developing advanced, high‐performance polymer nanocomposites.
- Open Access
- 17 May 2026
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 11 (21) , 31618-31626
Interfacial Separation of Insert Injection-Molded PS/Al Joints Induced by a UV/Heat-Activated Foaming Polymer
This paper presents the results of a study on the use of a thermoacid-triggered delamination system based on poly(tert-butoxycarbonyl styrene) [p(t-BocSt)] for controlling the separation of polystyrene/aluminum (PS/Al) insert injection-molded joints. The concept relies on a double-unlocking mechanism in which irradiation by ultraviolet (UV) light and subsequent thermal treatment are required to activate foaming within the p(t-BocSt) layer. Morphology study confirmed that uniform, defect-free interfaces were obtained prior to foaming, whereas postactivation samples exhibited pore formation and localized delamination due to CO2 and isobutene gas release during thermal decomposition. Tensile shear testing showed the PS/Al joint strength to be approximately 326 N for a single coating layer. Following the foaming process, the joint strength decreased by up to 84%, demonstrating that interfacial weakening and separation could be precisely controlled by the activation sequence. Overall, the proposed p(t-BocSt) system provides a controllable and separable polymer–metal bonding platform.
- 17 May 2026
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 11 (21) , 31618-31626
Open AccessInterfacial Separation of Insert Injection-Molded PS/Al Joints Induced by a UV/Heat-Activated Foaming Polymer
This paper presents the results of a study on the use of a thermoacid-triggered delamination system based on poly(tert-butoxycarbonyl styrene) [p(t-BocSt)] for controlling the separation of polystyrene/aluminum (PS/Al) insert injection-molded joints. The concept relies on a double-unlocking mechanism in which irradiation by ultraviolet (UV) light and subsequent thermal treatment are required to activate foaming within the p(t-BocSt) layer. Morphology study confirmed that uniform, defect-free interfaces were obtained prior to foaming, whereas postactivation samples exhibited pore formation and localized delamination due to CO2 and isobutene gas release during thermal decomposition. Tensile shear testing showed the PS/Al joint strength to be approximately 326 N for a single coating layer. Following the foaming process, the joint strength decreased by up to 84%, demonstrating that interfacial weakening and separation could be precisely controlled by the activation sequence. Overall, the proposed p(t-BocSt) system provides a controllable and separable polymer–metal bonding platform.
- 12 May 2026
- Published by Walter de Gruyter GmbH in Journal of Polymer Engineering
Sustained release of sodium tetradecyl sulfate from injectable degradable poly(ethylene glycol)-block-poly(propylene glycol)-block-poly(ethylene glycol) copolymers
We developed a degradable pluronic F-127 (PF-127)–based drug delivery system-poly(ethylene glycol)-block-poly(propylene glycol)-block-poly(ethylene glycol)–to localize STS and control its release directly at the target vein. The characteristics of the STS-loaded depot were assessed, and in vitro release profiles were quantified by high-performance liquid chromatography (HPLC). The in vivo elution behavior of STS from PF-127 was further evaluated in a rabbit vein model by administering equal doses of STS either as free drug or formulated within PF-127. This novel sustained-delivery approach provided continuous STS release for more than 14 days in vitro and achieved prolonged, high local STS levels in the rabbit ear vein for up to 28 days, while keeping systemic concentrations low. In addition, the PF-127-based drug delivery system significantly attenuated the initial burst release observed with free STS, indicating a more controlled pharmacokinetic profile. Collectively, these quantitative findings show that the PF-127-based system adds clear value over free STS by extending local exposure, reducing peak-driven losses and off-target exposure, and potentially improving therapeutic durability for the treatment of varicose veins.
- 12 May 2026
- Published by Walter de Gruyter GmbH in Journal of Polymer Engineering
Sustained release of sodium tetradecyl sulfate from injectable degradable poly(ethylene glycol)-block-poly(propylene glycol)-block-poly(ethylene glycol) copolymers
We developed a degradable pluronic F-127 (PF-127)–based drug delivery system-poly(ethylene glycol)-block-poly(propylene glycol)-block-poly(ethylene glycol)–to localize STS and control its release directly at the target vein. The characteristics of the STS-loaded depot were assessed, and in vitro release profiles were quantified by high-performance liquid chromatography (HPLC). The in vivo elution behavior of STS from PF-127 was further evaluated in a rabbit vein model by administering equal doses of STS either as free drug or formulated within PF-127. This novel sustained-delivery approach provided continuous STS release for more than 14 days in vitro and achieved prolonged, high local STS levels in the rabbit ear vein for up to 28 days, while keeping systemic concentrations low. In addition, the PF-127-based drug delivery system significantly attenuated the initial burst release observed with free STS, indicating a more controlled pharmacokinetic profile. Collectively, these quantitative findings show that the PF-127-based system adds clear value over free STS by extending local exposure, reducing peak-driven losses and off-target exposure, and potentially improving therapeutic durability for the treatment of varicose veins.
- Open Access
Polymer Gels Exhibiting High Pressure-Sensitive Adhesion to Polytetrafluoroethylene
Polytetrafluoroethylene (PTFE) is attractive for high-frequency communications but adheres very poorly to other materials due to its very low surface energy. Conventionally, surface treatments of PTFE are used to increase the polarity of the PTFE surface and enable bonding to materials with increased surface free energy. However, surface treatments are difficult to scale, can damage surfaces, and often lack reproducibility. Therefore, developing a material that can make PTFE adhere well to other materials without surface treatment is highly desirable. In this study, we aimed to develop a new material with strong adhesion to PTFE. We synthesized three polymer gels from dodecyl acrylate (DA) and 2-(dimethylamino) ethyl acrylate (DMAE): the homopolymer gels PDEAE and PDA, and the copolymer gel P(DEAE-co-DA). The copolymer gel P(DEAE-co-DA) exhibited high pressure-sensitive adhesion to PTFE, recording the highest adhesive strength (F = 430.0 N/m) and the highest peel energy (G = 713.4 J/m2) compared to the homopolymer gels PDEAE and PDA. Mechanical testing showed PDEAE had the greatest strength and toughness, PDA balanced stiffness and extensibility, and P(DEAE-co-DA) was the most flexible and extensible. The P(DEAE-co-DA) with the smoothest surface (Sz ≈ 0.176 µm) showed the highest F and G, implying that surface roughness did not contribute significantly to the interfacial adhesion between the gels and the PTFE. Based on the surface free energy and work of adhesion values, the adhesive strength to PTFE was predicted to be PDEAE > P(DEAE-co-DA) > PDA, but the measured G in peel tests contradicted this, indicating that the gels’ viscoelastic deformation and energy dissipation dominate the measured F and G. The frequency-dependent viscoelastic data and relaxation times τ and activation energies suggested optimal adhesion requires a balance of adhesion (mobility for energy dissipation (short τ, low )) and sufficient cohesion (high G′). P(DEAE-co-DA) achieved this balance, explaining its high measured F and G. With precise control of polymer chain mobility, the adhesion of P(DEAE-co-DA) gels can likely be improved further. Future work will employ block copolymerization and monomer-ratio control to tune molecular motion and enhance adhesion to PTFE.Open AccessPolymer Gels Exhibiting High Pressure-Sensitive Adhesion to Polytetrafluoroethylene
Polytetrafluoroethylene (PTFE) is attractive for high-frequency communications but adheres very poorly to other materials due to its very low surface energy. Conventionally, surface treatments of PTFE are used to increase the polarity of the PTFE surface and enable bonding to materials with increased surface free energy. However, surface treatments are difficult to scale, can damage surfaces, and often lack reproducibility. Therefore, developing a material that can make PTFE adhere well to other materials without surface treatment is highly desirable. In this study, we aimed to develop a new material with strong adhesion to PTFE. We synthesized three polymer gels from dodecyl acrylate (DA) and 2-(dimethylamino) ethyl acrylate (DMAE): the homopolymer gels PDEAE and PDA, and the copolymer gel P(DEAE-co-DA). The copolymer gel P(DEAE-co-DA) exhibited high pressure-sensitive adhesion to PTFE, recording the highest adhesive strength (F = 430.0 N/m) and the highest peel energy (G = 713.4 J/m2) compared to the homopolymer gels PDEAE and PDA. Mechanical testing showed PDEAE had the greatest strength and toughness, PDA balanced stiffness and extensibility, and P(DEAE-co-DA) was the most flexible and extensible. The P(DEAE-co-DA) with the smoothest surface (Sz ≈ 0.176 µm) showed the highest F and G, implying that surface roughness did not contribute significantly to the interfacial adhesion between the gels and the PTFE. Based on the surface free energy and work of adhesion values, the adhesive strength to PTFE was predicted to be PDEAE > P(DEAE-co-DA) > PDA, but the measured G in peel tests contradicted this, indicating that the gels’ viscoelastic deformation and energy dissipation dominate the measured F and G. The frequency-dependent viscoelastic data and relaxation times τ and activation energies suggested optimal adhesion requires a balance of adhesion (mobility for energy dissipation (short τ, low )) and sufficient cohesion (high G′). P(DEAE-co-DA) achieved this balance, explaining its high measured F and G. With precise control of polymer chain mobility, the adhesion of P(DEAE-co-DA) gels can likely be improved further. Future work will employ block copolymerization and monomer-ratio control to tune molecular motion and enhance adhesion to PTFE. - 12 February 2026
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 59 (4) , 2261-2270
Effect of Annealing on Creep Behavior and Density Fluctuations in Polycarbonate Investigated Using Time-Resolved SAXS/WAXS
- 12 February 2026
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 59 (4) , 2261-2270
Effect of Annealing on Creep Behavior and Density Fluctuations in Polycarbonate Investigated Using Time-Resolved SAXS/WAXS
- Open Access
Molecular Orientation and Mechanical Properties of Biomass-Derived Aliphatic Polyamide (PA11) by High-Pressure Compression Molding
This study investigates the effects of high-pressure compression molding on the molecular orientation and mechanical properties of biomass-derived aliphatic polyamide (PA11). Tensile fracture strength exhibited a significant increase—up to 2.4 times that of untreated samples—under conditions of 1000 kN and 140 °C. Differential Scanning Calorimetry (DSC) and Wide-Angle X-ray Scattering (WAXS) analyses revealed a temperature- and pressure-dependent shift in crystalline phases, suggesting a transition from α’ to phase. The δ’ phase, formed by high-pressure compression molding, is retained even after cooling to room temperature (i.e., Brill transition was not observed). In addition, polarized optical microscopy (POM) observations further supported the presence of changes in molecular orientation. This enhancement (under conditions of 1000 kN and 140 °C) is primarily attributed to the molecular orientation. However, it is also noteworthy that the formation of the δ’ phase is accompanied by an increase in the degree of crystallinity, and that this δ’ phase is retained even after cooling to room temperature without undergoing a Brill transition. In contrast, at 180 °C, although the degree of crystallinity increased, molecular orientation decreased, resulting in reduced tensile strength. These findings indicate that the mechanical properties of PA11 are governed by a complex interplay among phase transitions, molecular orientation, and crystallization, all of which are strongly influenced by temperature and pressure conditions. These findings demonstrate that high-pressure compression molding is an effective method for enhancing the mechanical properties of PA11 through controlled phase transition and orientation
Open AccessMolecular Orientation and Mechanical Properties of Biomass-Derived Aliphatic Polyamide (PA11) by High-Pressure Compression Molding
This study investigates the effects of high-pressure compression molding on the molecular orientation and mechanical properties of biomass-derived aliphatic polyamide (PA11). Tensile fracture strength exhibited a significant increase—up to 2.4 times that of untreated samples—under conditions of 1000 kN and 140 °C. Differential Scanning Calorimetry (DSC) and Wide-Angle X-ray Scattering (WAXS) analyses revealed a temperature- and pressure-dependent shift in crystalline phases, suggesting a transition from α’ to phase. The δ’ phase, formed by high-pressure compression molding, is retained even after cooling to room temperature (i.e., Brill transition was not observed). In addition, polarized optical microscopy (POM) observations further supported the presence of changes in molecular orientation. This enhancement (under conditions of 1000 kN and 140 °C) is primarily attributed to the molecular orientation. However, it is also noteworthy that the formation of the δ’ phase is accompanied by an increase in the degree of crystallinity, and that this δ’ phase is retained even after cooling to room temperature without undergoing a Brill transition. In contrast, at 180 °C, although the degree of crystallinity increased, molecular orientation decreased, resulting in reduced tensile strength. These findings indicate that the mechanical properties of PA11 are governed by a complex interplay among phase transitions, molecular orientation, and crystallization, all of which are strongly influenced by temperature and pressure conditions. These findings demonstrate that high-pressure compression molding is an effective method for enhancing the mechanical properties of PA11 through controlled phase transition and orientation
- Open Access
Synthesis of High-Performance and Biodegradable Polymer Blends Based on Poly(butylene succinate) and Grafted Polyrotaxane via Controlled Reactive Processing
In this study, novel, high-strength polymer blends were synthesized using poly(butylene succinate) (PBS) modified with grafted polyrotaxane (GPR). Then, their mechanical properties and morphologies were evaluated. A unique, two-step, reactive kneading method was developed to substantially improve the mechanical properties of PBS, which promoted transesterification reaction using an organo-titanium catalyst (Ti) in the first step and a urethanization reaction using hexamethylene diisocyanate (HDI) in the second step. The optimized blend material, [PBS/GPR10/Ti]-HDI, achieved remarkable toughening, and its Izod impact strength increased approximately seven-fold compared with that of unmodified PBS. Scanning electron microscopy (SEM) of the fracture surfaces confirmed a transition from brittle to ductile fracture, attributed to the controlled reaction sequence. First, strong chemical bonds formed at the PBS/GPR interface via Ti-catalyzed transesterification. Then, HDI induced simultaneous internal crosslinking (gelation) of the GPR domains and chain extension of the PBS matrix. This modification strategy maintained the excellent inherent soil biodegradability of PBS while improving its degradability in marine environments. This study presents a new guideline for designing materials that can considerably enhance the mechanical properties of biodegradable plastics.
Open AccessSynthesis of High-Performance and Biodegradable Polymer Blends Based on Poly(butylene succinate) and Grafted Polyrotaxane via Controlled Reactive Processing
In this study, novel, high-strength polymer blends were synthesized using poly(butylene succinate) (PBS) modified with grafted polyrotaxane (GPR). Then, their mechanical properties and morphologies were evaluated. A unique, two-step, reactive kneading method was developed to substantially improve the mechanical properties of PBS, which promoted transesterification reaction using an organo-titanium catalyst (Ti) in the first step and a urethanization reaction using hexamethylene diisocyanate (HDI) in the second step. The optimized blend material, [PBS/GPR10/Ti]-HDI, achieved remarkable toughening, and its Izod impact strength increased approximately seven-fold compared with that of unmodified PBS. Scanning electron microscopy (SEM) of the fracture surfaces confirmed a transition from brittle to ductile fracture, attributed to the controlled reaction sequence. First, strong chemical bonds formed at the PBS/GPR interface via Ti-catalyzed transesterification. Then, HDI induced simultaneous internal crosslinking (gelation) of the GPR domains and chain extension of the PBS matrix. This modification strategy maintained the excellent inherent soil biodegradability of PBS while improving its degradability in marine environments. This study presents a new guideline for designing materials that can considerably enhance the mechanical properties of biodegradable plastics.
- 23 June 2025
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 41 (25) , 16150-16159
Influence of Ultraviolet Light-Induced Photooxidation on the Surface Chemistry and Biodegradability of Aliphatic Polyamide Films
This study examines the environmental degradation of polyamides (PAs) with varying methylene group content from the perspective of polymer surface chemistry. PA4, PA6, PA11, and PA12 films were subjected to ultraviolet (UV) exposure to simulate environmental photooxidation, and subsequent changes in surface morphology and wettability were analyzed using laser microscopy and contact angle measurements. After 4 weeks of UV exposure, PA11 and PA12, which contain longer alkylene chains, exhibited more pronounced and denser surface cracks than PA4 and PA6. UV exposure increased the surface wettability of all samples, indicating photooxidation, as confirmed by Fourier-transform infrared (FT-IR) spectroscopy. The photooxidation rate followed the order: PA4 < PA6 < PA11 < PA12. Biodegradation was assessed by immersing pristine and UV-exposed films in extracted seawater. While pristine PA4 and PA6 developed biofilms, indicating biodegradation, PA11 and PA12 remained resistant. However, UV exposure rendered PA11 and PA12 biodegradable, likely due to the formation of lower-molecular-weight, soluble photooxidation products that facilitated microbial attack. UV exposure also enhanced the biodegradability of PA4 and PA6. Wide- and small-angle X-ray scattering analyses revealed that both photooxidation and biodegradation predominantly affected the amorphous regions of the polymers. These findings highlight the role of surface chemistry in the environmental fate of polyamides and the potential for UV-induced degradation to influence their biodegradability.
- 23 June 2025
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 41 (25) , 16150-16159
Influence of Ultraviolet Light-Induced Photooxidation on the Surface Chemistry and Biodegradability of Aliphatic Polyamide Films
This study examines the environmental degradation of polyamides (PAs) with varying methylene group content from the perspective of polymer surface chemistry. PA4, PA6, PA11, and PA12 films were subjected to ultraviolet (UV) exposure to simulate environmental photooxidation, and subsequent changes in surface morphology and wettability were analyzed using laser microscopy and contact angle measurements. After 4 weeks of UV exposure, PA11 and PA12, which contain longer alkylene chains, exhibited more pronounced and denser surface cracks than PA4 and PA6. UV exposure increased the surface wettability of all samples, indicating photooxidation, as confirmed by Fourier-transform infrared (FT-IR) spectroscopy. The photooxidation rate followed the order: PA4 < PA6 < PA11 < PA12. Biodegradation was assessed by immersing pristine and UV-exposed films in extracted seawater. While pristine PA4 and PA6 developed biofilms, indicating biodegradation, PA11 and PA12 remained resistant. However, UV exposure rendered PA11 and PA12 biodegradable, likely due to the formation of lower-molecular-weight, soluble photooxidation products that facilitated microbial attack. UV exposure also enhanced the biodegradability of PA4 and PA6. Wide- and small-angle X-ray scattering analyses revealed that both photooxidation and biodegradation predominantly affected the amorphous regions of the polymers. These findings highlight the role of surface chemistry in the environmental fate of polyamides and the potential for UV-induced degradation to influence their biodegradability.
- 21 April 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (17) , 25754-25763
Enhancing Mechanical Durability of Water-Soluble Microneedles with Cellulose Nanofibers via Thermal Imprinting
The study demonstrates the effectiveness of ultrahigh-pressure homogenizer (UHPH) cellulose nanofibers (CNFs) in improving the mechanical properties of poly(vinyl alcohol) (PVA) microneedle arrays (MNA). CNFs were incorporated into PVA nanocomposite films at concentrations of 0, 5, and 8 wt % using solvent casting and a nickel mold coated with a fluoropolymer was used to thermally imprint the films with MNA micropatterns at optimal mold temperatures and pressing pressure. The integration of CNFs substantially enhanced the morphological properties, surface modulus, and the accuracy of pattern replication in the nanocomposite. The augmented mechanical strength observed in the micropatterns, attributed to CNFs and subjected to UHPH treatment, can be ascribed to the physical entanglement and hydrogen bonding facilitating formation within the MNA micropattern.
- 21 April 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (17) , 25754-25763
Enhancing Mechanical Durability of Water-Soluble Microneedles with Cellulose Nanofibers via Thermal Imprinting
The study demonstrates the effectiveness of ultrahigh-pressure homogenizer (UHPH) cellulose nanofibers (CNFs) in improving the mechanical properties of poly(vinyl alcohol) (PVA) microneedle arrays (MNA). CNFs were incorporated into PVA nanocomposite films at concentrations of 0, 5, and 8 wt % using solvent casting and a nickel mold coated with a fluoropolymer was used to thermally imprint the films with MNA micropatterns at optimal mold temperatures and pressing pressure. The integration of CNFs substantially enhanced the morphological properties, surface modulus, and the accuracy of pattern replication in the nanocomposite. The augmented mechanical strength observed in the micropatterns, attributed to CNFs and subjected to UHPH treatment, can be ascribed to the physical entanglement and hydrogen bonding facilitating formation within the MNA micropattern.