Bertrand Jodoin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Bertrand Jodoin has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
A. Hawkins
Cold Spray Laboratory, University of Ottawa, Ottawa, Canada
3 shared publicationsA. Nastic
Cold Spray Laboratory, University of Ottawa, Ottawa, Canada
3 shared publicationsD. Guo
Cold Spray Laboratory, University of Ottawa, Ottawa, Canada
3 shared publicationsD. MacDonald
Cold Spray Laboratory, University of Ottawa, Ottawa, Canada
3 shared publicationsM. Kazasidis
Trinity College Dublin, The University of Dublin, Department of Mechanical, Manufacturing & Biomedical Engineering, Dublin, Ireland
3 shared publicationsM. Razavipour
Cold Spray Laboratory, University of Ottawa, Ottawa, Canada
3 shared publications
Latest Publications
- 29 January 2025
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 147 (9) , 1-28
Effects of Lattice Orientation Angle on TPMS-Based Transpiration Cooling
Establishing a continuous cooling film is an effective way to thermally protect hot-gas path components of gas turbines. For aero-engines, effusion cooling is the state-of-the-art method for developing cooling films. However, the cooling film generated by this method is far from ideal, as discrete miniature cooling air jets exiting from effusion cooling holes leave large gaps between cooling holes without adequate cooling film protection. Furthermore, effusion cooling jets can experience strong liftoff from component surfaces and are subsequently diluted due to mixing with the main flow. Recent advances in additive manufacturing (AM) technologies have enabled the fabrication of porous materials with precisely engineered lattice structures, significantly enhancing the film cooling effectiveness of hot-gas path components through transpiration cooling. A prior study has demonstrated highly promising transpiration cooling results by using a family of lattice geometries referred to as triply periodic minimal surface (TPMS) lattices. The present study experimentally investigates the influence of various TPMS lattice orientations on the film cooling effectiveness. Three types of TPMS structures, namely, diamond, Koch, and gyroid, are compared to demonstrate that the TPMS lattice orientation angle affects transpiration cooling performance, with different levels of sensitivity according to the TPMS structure. The TPMS lattice structures studied in this investigation are fabricated by stereolithography (SLA) three-dimensional printing. The adiabatic cooling film effectiveness (AFE) is measured using pressure sensitive paint (PSP).
- 29 January 2025
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 147 (9) , 1-28
Effects of Lattice Orientation Angle on TPMS-Based Transpiration Cooling
Establishing a continuous cooling film is an effective way to thermally protect hot-gas path components of gas turbines. For aero-engines, effusion cooling is the state-of-the-art method for developing cooling films. However, the cooling film generated by this method is far from ideal, as discrete miniature cooling air jets exiting from effusion cooling holes leave large gaps between cooling holes without adequate cooling film protection. Furthermore, effusion cooling jets can experience strong liftoff from component surfaces and are subsequently diluted due to mixing with the main flow. Recent advances in additive manufacturing (AM) technologies have enabled the fabrication of porous materials with precisely engineered lattice structures, significantly enhancing the film cooling effectiveness of hot-gas path components through transpiration cooling. A prior study has demonstrated highly promising transpiration cooling results by using a family of lattice geometries referred to as triply periodic minimal surface (TPMS) lattices. The present study experimentally investigates the influence of various TPMS lattice orientations on the film cooling effectiveness. Three types of TPMS structures, namely, diamond, Koch, and gyroid, are compared to demonstrate that the TPMS lattice orientation angle affects transpiration cooling performance, with different levels of sensitivity according to the TPMS structure. The TPMS lattice structures studied in this investigation are fabricated by stereolithography (SLA) three-dimensional printing. The adiabatic cooling film effectiveness (AFE) is measured using pressure sensitive paint (PSP).
- Open Access
- 25 October 2022
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 32 (1) , 322
Correction to: Cold Spray: Over 30 Years of Development Toward a Hot Future
- 25 October 2022
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 32 (1) , 322
Open AccessCorrection to: Cold Spray: Over 30 Years of Development Toward a Hot Future
- Open Access
- 13 June 2022
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 31 (7) , 2244
Correction to: Cold Spray: Over 30 Years of Development Toward a Hot Future
- 13 June 2022
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 31 (7) , 2244
Open AccessCorrection to: Cold Spray: Over 30 Years of Development Toward a Hot Future
- Top Cited PapersOpen Access
- 2 May 2022
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 31 (4) , 866-907
Cold Spray: Over 30 Years of Development Toward a Hot Future
Cold Spray (CS) is a deposition process, part of the thermal spray family. In this method, powder particles are accelerated at supersonic speed within a nozzle; impacts against a substrate material triggers a complex process, ultimately leading to consolidation and bonding. CS, in its modern form, has been around for approximately 30 years and has undergone through exciting and unprecedented developmental steps. In this article, we have summarized the key inventions and sub-inventions which pioneered the innovation aspect to the process that is known today, and the key breakthroughs related to the processing of materials CS is currently mastering. CS has not followed a liner path since its invention, but an evolution more similar to a hype cycle: high initial growth of expectations, followed by a decrease in interest and a renewed thrust pushed by a number of demonstrated industrial applications. The process interest is expected to continue (gently) to grow, alongside with further development of equipment and feedstock materials specific for CS processing. A number of current applications have been identified the areas that the process is likely to be the most disruptive in the medium-long term future have been laid down.
- 2 May 2022
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 31 (4) , 866-907
Top Cited PapersOpen AccessCold Spray: Over 30 Years of Development Toward a Hot Future
Cold Spray (CS) is a deposition process, part of the thermal spray family. In this method, powder particles are accelerated at supersonic speed within a nozzle; impacts against a substrate material triggers a complex process, ultimately leading to consolidation and bonding. CS, in its modern form, has been around for approximately 30 years and has undergone through exciting and unprecedented developmental steps. In this article, we have summarized the key inventions and sub-inventions which pioneered the innovation aspect to the process that is known today, and the key breakthroughs related to the processing of materials CS is currently mastering. CS has not followed a liner path since its invention, but an evolution more similar to a hype cycle: high initial growth of expectations, followed by a decrease in interest and a renewed thrust pushed by a number of demonstrated industrial applications. The process interest is expected to continue (gently) to grow, alongside with further development of equipment and feedstock materials specific for CS processing. A number of current applications have been identified the areas that the process is likely to be the most disruptive in the medium-long term future have been laid down.