Zhu Luo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Zhu Luo has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Bing Cai
National Institute of Metrology, Beijing 100029, China
2 shared publications - Jiacheng Cai
Research Institute of Highway Ministry of Transport, Beijing 100088, China
2 shared publications - Jianjun Cui
National Institute of Metrology, Beijing 100029, China
2 shared publications - Kai Chen
National Institute of Metrology, Beijing 100029, China
2 shared publications - Lu Liu
Research Institute of Highway Ministry of Transport, Beijing 100088, China
2 shared publications - Lu Peng
Research Institute of Highway Ministry of Transport, Beijing 100088, China
2 shared publications
Latest Publications
- Open Access
A Graded Evaluation Method for Construction Quality of Prefabricated Beam Bridges Based on Manifold Learning and Probability Distributions
This study aims to construct a graded evaluation method for the construction quality of Highway Prefabricated Beam Bridges, in order to support refined quality control beyond the traditional “qualified/unqualified” judgment. Existing evaluation methods have difficulty effectively distinguishing quality differences within the qualified range, may cause redundant calculations for indicator information with non-linear correlations, are susceptible to the influence of outlier expert judgments, and may mask local critical defects when adopting linear weighted aggregation. This paper uses historical quality inspection and expert evaluation records from 50 prefabricated beam bridges to validate the proposed method. Experimental results show that the proposed method achieves an RMSE of 1.24, outperforming the traditional AHP method (1.79) and the equal-weight method (2.52). Five-fold grouped cross-validation at the bridge level gave an RMSE of 1.2180 ± 0.0802 and an R2 of 0.9536. It can provide accurate intelligent decision support for quality and safety control during the construction of Highway Prefabricated Beam Bridges, and promotes the digital upgrade of quality management in the construction industry. The proposed framework can be integrated into a digital construction quality management platform to support bridge quality ranking and early warning of safety-critical defects. The originality of this paper lies in the integration, within a unified evaluation framework, of continuous score conversion based on probability distributions, manifold-learning-based redundancy correction for indicators, geometrically median-based robust fusion of expert weights, and a threshold-triggered risk-sensitive weight adjustment mechanism.
Open AccessA Graded Evaluation Method for Construction Quality of Prefabricated Beam Bridges Based on Manifold Learning and Probability Distributions
This study aims to construct a graded evaluation method for the construction quality of Highway Prefabricated Beam Bridges, in order to support refined quality control beyond the traditional “qualified/unqualified” judgment. Existing evaluation methods have difficulty effectively distinguishing quality differences within the qualified range, may cause redundant calculations for indicator information with non-linear correlations, are susceptible to the influence of outlier expert judgments, and may mask local critical defects when adopting linear weighted aggregation. This paper uses historical quality inspection and expert evaluation records from 50 prefabricated beam bridges to validate the proposed method. Experimental results show that the proposed method achieves an RMSE of 1.24, outperforming the traditional AHP method (1.79) and the equal-weight method (2.52). Five-fold grouped cross-validation at the bridge level gave an RMSE of 1.2180 ± 0.0802 and an R2 of 0.9536. It can provide accurate intelligent decision support for quality and safety control during the construction of Highway Prefabricated Beam Bridges, and promotes the digital upgrade of quality management in the construction industry. The proposed framework can be integrated into a digital construction quality management platform to support bridge quality ranking and early warning of safety-critical defects. The originality of this paper lies in the integration, within a unified evaluation framework, of continuous score conversion based on probability distributions, manifold-learning-based redundancy correction for indicators, geometrically median-based robust fusion of expert weights, and a threshold-triggered risk-sensitive weight adjustment mechanism.
- Open Access
- 31 August 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (17) , 8649
Intelligent Quality Evaluation Method for Highway Prefabricated Beam Bridges Based on Key Parameter Control and Weighted Neural Network Optimization
To reduce dependence on expert judgement and improve the consistency and resolution of construction quality evaluation for highway prefabricated girder bridges (HPGBs), this study proposes an intelligent evaluation method integrating key parameter control and weighted neural network optimization. First, a three-level evaluation system covering the finished bridge, first-level indicators, and secondary indicators is established for the full construction process from prefabrication to installation. Threshold-type indicators are scored using a two-point rule, whereas finite interval indicators are converted into continuous scores using a two-sided piecewise-normalized truncated normal model. Grey relational analysis is then used to identify key quality parameters and quantify inter-indicator relational strength, and an adaptive weight decay mechanism attenuates redundant non-key indicators while retaining the key parameters. Data-driven indicator importance is subsequently learned using a weighted neural network, and hierarchical weighted aggregation is used to obtain the final bridge score. The model development database contains 10 HPGBs and nine expert evaluations per bridge, yielding 90 labelled expert-bridge records; Bridges 1–7 were used for training and Bridges 8–10 for bridge-wise testing. On the test set, the proposed method achieved R2 = 0.9147, RMSE = 1.294, MAE = 1.0987, and MRE = 1.36%. Compared with the traditional AHP method, MAE was reduced by approximately 22.01%, and R2 increased by approximately 5.86%. An engineering application yielded a comprehensive score of 84.4, corresponding to Grade B. These results demonstrate the feasibility of the proposed framework for refined quality evaluation within the HPGB class considered in this study.
- 31 August 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (17) , 8649
Open AccessIntelligent Quality Evaluation Method for Highway Prefabricated Beam Bridges Based on Key Parameter Control and Weighted Neural Network Optimization
To reduce dependence on expert judgement and improve the consistency and resolution of construction quality evaluation for highway prefabricated girder bridges (HPGBs), this study proposes an intelligent evaluation method integrating key parameter control and weighted neural network optimization. First, a three-level evaluation system covering the finished bridge, first-level indicators, and secondary indicators is established for the full construction process from prefabrication to installation. Threshold-type indicators are scored using a two-point rule, whereas finite interval indicators are converted into continuous scores using a two-sided piecewise-normalized truncated normal model. Grey relational analysis is then used to identify key quality parameters and quantify inter-indicator relational strength, and an adaptive weight decay mechanism attenuates redundant non-key indicators while retaining the key parameters. Data-driven indicator importance is subsequently learned using a weighted neural network, and hierarchical weighted aggregation is used to obtain the final bridge score. The model development database contains 10 HPGBs and nine expert evaluations per bridge, yielding 90 labelled expert-bridge records; Bridges 1–7 were used for training and Bridges 8–10 for bridge-wise testing. On the test set, the proposed method achieved R2 = 0.9147, RMSE = 1.294, MAE = 1.0987, and MRE = 1.36%. Compared with the traditional AHP method, MAE was reduced by approximately 22.01%, and R2 increased by approximately 5.86%. An engineering application yielded a comprehensive score of 84.4, corresponding to Grade B. These results demonstrate the feasibility of the proposed framework for refined quality evaluation within the HPGB class considered in this study.
- Open Access
- 1 February 2021
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 669 (1) , 012007
Deformation modulus tested by the falling ball test method and the experimental verification
In filling engineering, the mechanical properties of geomaterials are the most important mechanical indicators. With the improvement of the measurement technology, the falling ball test (FBT) method has been gradually popularized and applied to the testing of geomaterials mechanical properties. In order to verify the testing accuracy of the FBT method, experimental results of the deformation modulus tested for the homogeneous fine-grained materials and the layered structures using the FBT method are compared with the K 30 plate load test, which is the earliest and the most widely used in-situ test method. And some conclusions are drawn in this present paper.
- 1 February 2021
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 669 (1) , 012007
Open AccessDeformation modulus tested by the falling ball test method and the experimental verification
In filling engineering, the mechanical properties of geomaterials are the most important mechanical indicators. With the improvement of the measurement technology, the falling ball test (FBT) method has been gradually popularized and applied to the testing of geomaterials mechanical properties. In order to verify the testing accuracy of the FBT method, experimental results of the deformation modulus tested for the homogeneous fine-grained materials and the layered structures using the FBT method are compared with the K 30 plate load test, which is the earliest and the most widely used in-situ test method. And some conclusions are drawn in this present paper.
- 23 July 2009
- Published by American Society of Civil Engineers (ASCE)
- p. 1-7
Analysis of Elastic Slab on Non-Uniform Support Foundation Using a Weighted-Residual Method
Based on the assumption of Kirchhoff thin plate, we derive the constitutive equations and the boundary conditions on all four edges for variable Winkler foundations to solve the problem of Cement Concrete Pavement (CCP) supported by a non-uniform foundation. The constitutive equation is a fourth-order differential equation with variable coefficients that has no known analytical solution. A Weighted-Residual Method (WRM) is developed to solve the problem approximately. In our WRM numerical tests, a mixed-type trial function, i.e., the biharmonic function, and a weight function based on the least-square method are selected to eliminate residual errors. Results show that, compared to the finite element method, the WRM computational method produces a relative error of only 3.2%, which satisfies the error requirement of general engineering applications. The novel WRM developed in this paper appears to be a good approximation method in solving the problem of CCP supported by non-uniform foundations.
- 23 July 2009
- Published by American Society of Civil Engineers (ASCE)
- p. 1-7
Analysis of Elastic Slab on Non-Uniform Support Foundation Using a Weighted-Residual Method
Based on the assumption of Kirchhoff thin plate, we derive the constitutive equations and the boundary conditions on all four edges for variable Winkler foundations to solve the problem of Cement Concrete Pavement (CCP) supported by a non-uniform foundation. The constitutive equation is a fourth-order differential equation with variable coefficients that has no known analytical solution. A Weighted-Residual Method (WRM) is developed to solve the problem approximately. In our WRM numerical tests, a mixed-type trial function, i.e., the biharmonic function, and a weight function based on the least-square method are selected to eliminate residual errors. Results show that, compared to the finite element method, the WRM computational method produces a relative error of only 3.2%, which satisfies the error requirement of general engineering applications. The novel WRM developed in this paper appears to be a good approximation method in solving the problem of CCP supported by non-uniform foundations.