Renda Zhao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Renda Zhao has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Junping Zhang
Department of Bridge, Southwest Jiaotong University, Chengdu 610031, China
3 shared publications Pengzhen Lu
2 shared publications- Pengzhen Lu
Department of Bridge, Southwest Jiaotong University, Chengdu 610031, China
2 shared publications Ping Liao
Southwest Jiaotong University
2 shared publicationsChangyu Shao
1 shared publication- Fuhai Li
School of Civil Engineering, Southwest Jiaotong University, Chengdu, China
1 shared publication
Latest Publications
- Open Access
Seismic Performance of Bridge Piers Constructed with PP-ECC at Potential Plastic Hinge Regions
This work presents an experimental investigation on the seismic performance of bridge piers constructed with polypropylene fiber reinforced engineered cementitious composite (PP-ECC) at potential plastic hinge regions. Eight solid square bridge piers are tested under a combination of reversed cyclic lateral loading and constant axial vertical loading. The test variables include the reinforcement stirrup ratio (0 vol.%, 0.46 vol.%, and 0.79 vol.%), axial compression ratio (0.1 and 0.3) and height of the PP-ECC regions (0, 250, and 500 mm). Seismic performance of eight specimens is presented and interpreted, including the failure mode, hysteretic curves, loading–resistance capacity, ductility, stiffness degradation, energy dissipation, and equivalent viscous damping ratio. The material test on the PP-ECC plate specimen suggests that the PP-ECC has obvious strain-hardening behavior and multiple fine-cracking characteristics, with the tensile strength and strain capacity greater than 3.2 MPa and 2.6%, respectively. The PP-ECC material applied at the potential plastic hinge regions notably improves the seismic performance and damage tolerance of bridge piers. The influence of the aforementioned crucial parameters has also been investigated in detail. The axial compression ratio and the height of PP-ECC region have a major influence on the seismic performance of PP-ECC piers. In comparison, the stirrup ratio has a limited effect on the seismic behavior of PP-ECC piers. The experimental findings shed light on the mechanism of the PP-ECC that contributes to the seismic performance of bridge piers and provide some valuable guidance in the seismic design of PP-ECC piers.
Open AccessSeismic Performance of Bridge Piers Constructed with PP-ECC at Potential Plastic Hinge Regions
This work presents an experimental investigation on the seismic performance of bridge piers constructed with polypropylene fiber reinforced engineered cementitious composite (PP-ECC) at potential plastic hinge regions. Eight solid square bridge piers are tested under a combination of reversed cyclic lateral loading and constant axial vertical loading. The test variables include the reinforcement stirrup ratio (0 vol.%, 0.46 vol.%, and 0.79 vol.%), axial compression ratio (0.1 and 0.3) and height of the PP-ECC regions (0, 250, and 500 mm). Seismic performance of eight specimens is presented and interpreted, including the failure mode, hysteretic curves, loading–resistance capacity, ductility, stiffness degradation, energy dissipation, and equivalent viscous damping ratio. The material test on the PP-ECC plate specimen suggests that the PP-ECC has obvious strain-hardening behavior and multiple fine-cracking characteristics, with the tensile strength and strain capacity greater than 3.2 MPa and 2.6%, respectively. The PP-ECC material applied at the potential plastic hinge regions notably improves the seismic performance and damage tolerance of bridge piers. The influence of the aforementioned crucial parameters has also been investigated in detail. The axial compression ratio and the height of PP-ECC region have a major influence on the seismic performance of PP-ECC piers. In comparison, the stirrup ratio has a limited effect on the seismic behavior of PP-ECC piers. The experimental findings shed light on the mechanism of the PP-ECC that contributes to the seismic performance of bridge piers and provide some valuable guidance in the seismic design of PP-ECC piers.
- Open Access
- 1 October 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 649 (1) , 012005
Model Experiment of Construction Process of Long-Span Concrete Arch Bridge Rigid Skeleton
High-speed railway passenger dedicated line have high demands for track smoothness, beipanjiang bridge as shanghai-kunming high-speed railway control project, mainspan 445m, constructed by using rigid skeleton, C80 high-strength concrete filled steel tube structure for the first time used in railway bridge; rigid skeleton in the process of construction has the traits: long span, long construction period, multi-step, mechanical behavior was extremely complex. In this paper, the design principle and similarity relation of rigid skeleton model are introduced, simplified the model construction process, and the finite element simulation analysis model is established, compared with measured values, it is shown that model test can well simulate the long span rigid skeleton arch bridge stress state in the construction process; the original construction steps have more safety reserves than simplified; the indicators of model test are within the scope of design, the results can provide technical support for the bridge construction.
- 1 October 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 649 (1) , 012005
Open AccessModel Experiment of Construction Process of Long-Span Concrete Arch Bridge Rigid Skeleton
High-speed railway passenger dedicated line have high demands for track smoothness, beipanjiang bridge as shanghai-kunming high-speed railway control project, mainspan 445m, constructed by using rigid skeleton, C80 high-strength concrete filled steel tube structure for the first time used in railway bridge; rigid skeleton in the process of construction has the traits: long span, long construction period, multi-step, mechanical behavior was extremely complex. In this paper, the design principle and similarity relation of rigid skeleton model are introduced, simplified the model construction process, and the finite element simulation analysis model is established, compared with measured values, it is shown that model test can well simulate the long span rigid skeleton arch bridge stress state in the construction process; the original construction steps have more safety reserves than simplified; the indicators of model test are within the scope of design, the results can provide technical support for the bridge construction.
- Open Access
- 18 September 2017
- Published by Springer Nature in Journal of Modern Transportation
- Vol. 25 (4) , 279-286
Stress concentration coefficients of optimized cope-hole welded detail
- 18 September 2017
- Published by Springer Nature in Journal of Modern Transportation
- Vol. 25 (4) , 279-286
Open AccessStress concentration coefficients of optimized cope-hole welded detail
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
Experimental study on mix proportion of fiber reinforced cementitious composites
To study the mechanical property of fiber reinforced cementations composites influenced by the fiber length, quartz sand diameter, matrix of water cement ratio, volume fraction of fiber and magnesium acrylate solution. Several 40×40×160 mm standard test specimens, “8” specimens and long “8” specimens and 21 groups of fiber concrete specimens were fabricated. The flexural, compressive and uniaxial tensile strength were tested by using the bending resistance, compression resistance and electronic universal testing machine. The results show that flexural and compressive strength of fiber reinforced cementations composites increases along with the increase of quartz sand diameter, with the growth of the PVA fiber length increases; When the water-binder ratio is 0.25 and powder-binder ratio is 0.3, the PVA fiber content is 1.5% of the mass of cementations materials, there is a phenomenon of strain hardening; The addition of magnesium acrylate solution reduces the tensile strength of PVA fiber reinforced cementations composites, the tensile strength of the specimens in the curing age of 7d is decreased by about 21% and the specimens in curing age of 28d is decreased by more than 50%.
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
Experimental study on mix proportion of fiber reinforced cementitious composites
To study the mechanical property of fiber reinforced cementations composites influenced by the fiber length, quartz sand diameter, matrix of water cement ratio, volume fraction of fiber and magnesium acrylate solution. Several 40×40×160 mm standard test specimens, “8” specimens and long “8” specimens and 21 groups of fiber concrete specimens were fabricated. The flexural, compressive and uniaxial tensile strength were tested by using the bending resistance, compression resistance and electronic universal testing machine. The results show that flexural and compressive strength of fiber reinforced cementations composites increases along with the increase of quartz sand diameter, with the growth of the PVA fiber length increases; When the water-binder ratio is 0.25 and powder-binder ratio is 0.3, the PVA fiber content is 1.5% of the mass of cementations materials, there is a phenomenon of strain hardening; The addition of magnesium acrylate solution reduces the tensile strength of PVA fiber reinforced cementations composites, the tensile strength of the specimens in the curing age of 7d is decreased by about 21% and the specimens in curing age of 28d is decreased by more than 50%.
- Open Access
- 1 January 2017
- Published by Academy of Science of South Africa in Journal of the South African Institution of Civil Engineering
- Vol. 59 (2) , 11-18
Fatigue behaviour in full-scale laboratory tests of a composite deck slab with PBL reinforcement
Studies on the fatigue behaviour of composite deck slabs are relatively few. To assess the fatigue performance of a composite deck slab at specific design loads, and to provide a reference for its design in fatigue, two full-scale models A and B of a composite deck slab were developed, comprising steel plates and steel-fibre-reinforced concrete slabs. These models will be a useful reference for experiments and design, and for developing codes. In this study we carried out fatigue experiments and focused on the fatigue performance of a composite deck slab in a column area, and the positive and negative bending moments. For the entire fatigue loading cycle, the overall performance of Models A and B was good, the overall stiffness of the composite deck slab was rarely attenuated, the stress levels in the steel members in relation to the fracture strength were not significant, and the steel member was in the stage of flexible work. Through comprehensive tests of Models A and B it was found that the original design exhibits good fatigue performance and meets the design requirements. The research results provide a basis for the design of a composite bridge deck slab in fatigue.
- 1 January 2017
- Published by Academy of Science of South Africa in Journal of the South African Institution of Civil Engineering
- Vol. 59 (2) , 11-18
Open AccessFatigue behaviour in full-scale laboratory tests of a composite deck slab with PBL reinforcement
Studies on the fatigue behaviour of composite deck slabs are relatively few. To assess the fatigue performance of a composite deck slab at specific design loads, and to provide a reference for its design in fatigue, two full-scale models A and B of a composite deck slab were developed, comprising steel plates and steel-fibre-reinforced concrete slabs. These models will be a useful reference for experiments and design, and for developing codes. In this study we carried out fatigue experiments and focused on the fatigue performance of a composite deck slab in a column area, and the positive and negative bending moments. For the entire fatigue loading cycle, the overall performance of Models A and B was good, the overall stiffness of the composite deck slab was rarely attenuated, the stress levels in the steel members in relation to the fracture strength were not significant, and the steel member was in the stage of flexible work. Through comprehensive tests of Models A and B it was found that the original design exhibits good fatigue performance and meets the design requirements. The research results provide a basis for the design of a composite bridge deck slab in fatigue.
- Open Access
- 1 March 2014
- Published by Prof. Marin Drinov Publishing House of BAS (Bulgarian Academy of Sciences) in Journal of Theoretical and Applied Mechanics
- Vol. 44 (1) , 79-96
LINEAR ANALYSIS AND SIMULATION OF INTERFACIAL SLIP BEHAVIOUR FOR COMPOSITE BOX GIRDERS
The slip at the steel-concrete interface in steel-concrete composite beams was studied analytically and numerically. A theoretical description for steel-concrete composite box beams with partial shear interaction based on the partial interaction theory was derived, and equilibrium of the rotation angle w′ was introduced to allow convenient computation of deformation of composite box beams. Numerical simulations of steel-concrete composite box beams subjected to concentrated load and/or uniformly distributed load were conducted. The analytical solutions show excellent agreement with the numerical results. For typical composite box beams used in practice, shear slip in partial composite box beams makes a significant contribution to beam deformation. Even for full composite box beams, slip effects may result in stiffness reduction. However, slip effects are ignored in many design specifications which use transformed section methods; an exception is the American Institute of Steel Construction [1] specifications, which recommend a calculation procedure in the commentary. Finally, the proposed method was extended to analyze the interface slip for shear connectors of different pitch and, to some extent, confirm the accuracy of the predictions.
- 1 March 2014
- Published by Prof. Marin Drinov Publishing House of BAS (Bulgarian Academy of Sciences) in Journal of Theoretical and Applied Mechanics
- Vol. 44 (1) , 79-96
Open AccessLINEAR ANALYSIS AND SIMULATION OF INTERFACIAL SLIP BEHAVIOUR FOR COMPOSITE BOX GIRDERS
The slip at the steel-concrete interface in steel-concrete composite beams was studied analytically and numerically. A theoretical description for steel-concrete composite box beams with partial shear interaction based on the partial interaction theory was derived, and equilibrium of the rotation angle w′ was introduced to allow convenient computation of deformation of composite box beams. Numerical simulations of steel-concrete composite box beams subjected to concentrated load and/or uniformly distributed load were conducted. The analytical solutions show excellent agreement with the numerical results. For typical composite box beams used in practice, shear slip in partial composite box beams makes a significant contribution to beam deformation. Even for full composite box beams, slip effects may result in stiffness reduction. However, slip effects are ignored in many design specifications which use transformed section methods; an exception is the American Institute of Steel Construction [1] specifications, which recommend a calculation procedure in the commentary. Finally, the proposed method was extended to analyze the interface slip for shear connectors of different pitch and, to some extent, confirm the accuracy of the predictions.
- 10 May 2010
- Published by Techno-Press in STRUCTURAL ENGINEERING AND MECHANICS
- Vol. 35 (1) , 37-52
Experimental and finite element studies of special-shape arch bridge for self-balance
- 10 May 2010
- Published by Techno-Press in STRUCTURAL ENGINEERING AND MECHANICS
- Vol. 35 (1) , 37-52
Experimental and finite element studies of special-shape arch bridge for self-balance
- 20 April 2010
- Published by Techno-Press in STRUCTURAL ENGINEERING AND MECHANICS
- Vol. 34 (6) , 801-804
A new analytical method for deformation of composite steel-concrete straight box girders with interfacial slip
- 20 April 2010
- Published by Techno-Press in STRUCTURAL ENGINEERING AND MECHANICS
- Vol. 34 (6) , 801-804
A new analytical method for deformation of composite steel-concrete straight box girders with interfacial slip
- 30 January 2009
- Published by Techno-Press in STRUCTURAL ENGINEERING AND MECHANICS
- Vol. 31 (2) , 137-152
Theoretical analysis of Y-shape bridge and application
- 30 January 2009
- Published by Techno-Press in STRUCTURAL ENGINEERING AND MECHANICS
- Vol. 31 (2) , 137-152
Theoretical analysis of Y-shape bridge and application
- 5 January 2009
- Published by American Society of Civil Engineers (ASCE)
- p. 2348-2353
The Test Study on Model of Special-Shape Bridge
Because of the mechanical characteristics of Y-shape Thin-walled Box Beam Bridge (YTBBB), the elementary theory of space general beam can not well solve the problem of the complex mechanical behavior of the YTBBB. In order to do that, authors selected a typical YTBBB from various Y-shape Bridges as research object, which is reduced and made into a polymethyl methacrylate model as the test model with 1/30 of the proportion according to the similar theory. This paper carries out model tests by using different deformation and text points, three kinds of bearings and six kinds of loading cases respectively. The testing results show that the problems of restrained twisting, distortion and shear-lag effect of the YTBBB are significant. Compared with the results derived from the elementary beam unit model, this model can correctly reflect the situation of the complex mechanical behavior of the YTBBB. On the basis of it, the calculation theory and analysis method of the YTBBB are proposed correspondingly, which offer an effective way for the YTBBB with complicated structure.
- 5 January 2009
- Published by American Society of Civil Engineers (ASCE)
- p. 2348-2353
The Test Study on Model of Special-Shape Bridge
Because of the mechanical characteristics of Y-shape Thin-walled Box Beam Bridge (YTBBB), the elementary theory of space general beam can not well solve the problem of the complex mechanical behavior of the YTBBB. In order to do that, authors selected a typical YTBBB from various Y-shape Bridges as research object, which is reduced and made into a polymethyl methacrylate model as the test model with 1/30 of the proportion according to the similar theory. This paper carries out model tests by using different deformation and text points, three kinds of bearings and six kinds of loading cases respectively. The testing results show that the problems of restrained twisting, distortion and shear-lag effect of the YTBBB are significant. Compared with the results derived from the elementary beam unit model, this model can correctly reflect the situation of the complex mechanical behavior of the YTBBB. On the basis of it, the calculation theory and analysis method of the YTBBB are proposed correspondingly, which offer an effective way for the YTBBB with complicated structure.