SPSamuel G. Paikowsky

Samuel G. Paikowsky

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Samuel G. Paikowsky has a total of 20 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Drop Weight Dynamic Load Testing for Construction Monitoring and Quality Control of Offshore Drilled Foundations

    by Seth O. Robertson, Samuel G. Paikowsky

    High strain drop weight dynamic load testing is an effective tool when evaluating the construction quality and axial capacity of offshore drilled deep foundations. This is a result of the complexity and cost of the alternative conventional static load tests. Drop weight systems can be designed for project specific needs, providing sufficient energy to mobilize the required resistance while permitting ease in transporting the device. Test shafts/piles can be instrumented and analyzed using the same dynamic testing techniques used for driven pile foundations. A case study is presented where drop weight dynamic load tests were utilized for offshore drilled shaft foundations. The project includes the design, construction, and quality control for a cement unloading pier at the Tema Port in Ghana, Africa. The foundations are unique, consisting of 0.8m outer diameter steel pipes embedded in 1.0m rock-socketed drilled shafts. Three dynamic load tests to failure and six load verification tests were performed offshore. The load verification tests were carried out due to construction difficulties and/or complex subsurface conditions. The piles’ integrity and mobilized resistances were assessed using the signal matching analysis software CAPWAP. The underlying assumptions in the one-dimensional wave equation formulation on which CAPWAP is based are violated in these complex cases. Finite element analyses were therefore performed using the PLAXIS 2D software in order to examine the validity of the one-dimensional wave equation application under such conditions. This paper briefly describes the project, the associated difficulties, the unique foundations, example load tests and their analyses, as well as some initial processing in examining the validity of the one-dimensional wave equation analyses under the tested conditions.


  • Characteristics and Engineering Properties of Peaty Soil Underlying Cranberry Bogs

    by Assem Elsayed, Samuel Paikowsky, Pradeep Kurup

    Peat is an organic complex soil, well known for its high compressibility and low stability. Peat forms naturally by the incomplete decomposition of plant and animal constituents under anaerobic conditions at low temperatures. A relocation of state highway No. 44 in Carver, Massachusetts requires the construction of sheet pile walls, fills and embankments through cranberry bogs and ponds containing deep peat deposits. The engineering properties of Carver peat in Southern Massachusetts (south of Boston) were investigated via laboratory testing including standard index tests, scanning electron micrographs, fiber content, engineering classification, permeability, consolidated undrained triaxial tests, and oedometer tests. The tests were carried out on vertically (V) and horizontally (H) oriented undisturbed samples. Unlike inorganic clays, the secondary compression of peat is of great significance as it dominates its deformation and takes place over a long period of time. The presented testing program examines the deformation properties of the peat. The biodegradation of peat seems to increase the coefficient of secondary compression Cα and the coefficient of tertiary compression Ck. The drained friction angle (from triaxial tests) of Carver peat yielded values of (12°) and (10°) for vertically and horizontally oriented samples, respectively. The drained cohesion intercept (from triaxial tests) was 11.45 (kPa) and 12.42 (kPa) for vertically and horizontally oriented samples, respectively. The obtained engineering properties were found to be overall within the range reported for other peat types.


  • LRFD Implementation Effects on Geotechnical Investigation and Design

    by Derrick Dasenbrock, Aaron Budge, Sam Paikowsky

    The Minnesota Department of Transportation has successfully implemented the Load and Resistance Factor Design (LRFD) method with respect to structural and geotechnical design of transportation structures. The implementation timeline, strategies, and processes are described, highlighting both the major adoption hurdles and the benefits that have been realized to date. In an effort to derive further benefits from the design method, Mn/DOT has a contract underway to develop regionally specific values for resistance factors used in design for driven pile foundations.


  • Uncertainties in the Bearing Capacity of Shallow Foundations and the Factor N y Using an Extensive Database

    by Shailendra Amatya, Samuel G. Paikowsky, Kerstin Lesny, Aloys Kisse

    A comprehensive database with 549 cases of load tests on shallow foundations, mostly in/on granular soils, was compiled as apart of two research projects (NCHRP 12–66 and NCHRP 24–31) carried out to develop the AASHTO (American Association of State Highway and Transportation Officials) Specifications for Highway Bridges. Based on this database, the uncertainties in the ultimate bearing capacity of footings in/on granular soils and under centric vertical loading were appraised. The proposal by Vesić (1963) was used for the interpretation of failure loads from load tests (measured capacity), while the equations given by Vesić (1975) was used to estimate the theoretical bearing capacities (BC) (calculated capacity). For the footings in soils with controlled compaction and with known particle sizes, it was found that Vesic (1975) gives conservative estimates. Further, the model uncertainty of the BC equation in terms of Nγ was examined for granular soils with friction angles between 42° and 46°, using the back-calculated values from 125 load tests carried out to failure for footings on granular soil surfaces and under vertical centric loadings.


  • Evaluation of Compaction Effects on Granular Backfill Using CPT

    by Y. Tan, G. Lin, S. G. Paikowsky, J. Fang

    This paper examines the cone penetration testing (CPT) results prior to and after two passes of deep dynamic compaction (DDC) to investigate compaction effects on the loose saturated granular backfill between steel sheet pile walls and peat bogs. The site characterization results show that the backfill was significantly densified after each pass of compaction. Two factors, (1) the existence of soft soil layers, and (2) severe liquefaction after DDC, greatly reduced compaction effects. The depth to which significant densification took place ranged from 6.5 to 9.5 m after the first pass of DDC, and 7.5 to 11 m after two passes. Finally, this paper recommends parameters for the evaluation of densification depth based on the comparison of the results from this study with those obtained from the literature.


  • Scale Effects in Lateral Load Response of Large Diameter Monopiles

    by K. Lesny, S. G. Paikowsky, A. Gurbuz

    Monopile foundations are frequently used for offshore wind energy converters. These piles are highly laterally loaded structures with large horizontal forces and bending moments. Due to the harsh environmental conditions in the southern North Sea diameters of 4 to 8 m are required to maintain serviceability. In common practice smaller laterally loaded pipe piles are designed using the well-known p-y-method, in which the pile-soil stiffness is considered by nonlinear p-y-curves derived from field tests. An alternative design method is the strain wedge method in which the pile response is derived from the stress-strain relationship of the soil assuming a certain failure zone ahead of the pile. In the present paper, the design of a large diameter monopile foundation for typical loading conditions is presented. The pile response in cohesionless soil determined by the p-y method and the strain wedge method is compared with a finite element (FE) analysis with respect to scale effects when extrapolated from commonly used pipe pile diameters to large size monopiles.


  • Prediction and Reliability of Pipe Piles Response to Lateral Loading

    by S. G. Paikowsky, Y. Lu, A. Gurbuz

    Load-deflection relations of piles subjected to lateral loading are routinely required for design. The use of large diameter open pipe piles became common since its application as foundations for offshore structures, and more recently for bridge retrofitting and new construction designed for withstanding earthquake loading. The accuracy and reliability of the analysis methods remains usually unknown as it requires the systematic examination of the measured performance of many piles. As part of a research aimed at developing the serviceability limit states for the AASHTO specifications, an evaluation of the methods predicting the response of piles to lateral loads was required. This paper presents a database of laterally loaded open and closed pipe piles which were examined by various analysis methods. The performance of the methods when applied to open pipe piles and all pipe piles is reported along with practical conclusions for their use.


  • Establishing Serviceability Limit State in the Design of Bridge Foundations

    by S. G. Paikowsky, Y. Lu

    An ongoing research project supported by the USA National Cooperative Highway Research Program (NCHRP) under the Transportation Research Board (TRB) of the National Academy of Science is aimed at developing the AASHTO LRFD Specifications for Serviceability in the Design of Bridge Foundations. The AASHTO specifications are traditionally observed on all federally aided projects and generally viewed as a national code of US highway practice, hence influencing the construction of all highway bridges throughout the USA. The development of the specifications requires: establishing serviceability criteria, compilation of databases for foundation displacements, determination of analysis methods, finding the uncertainty of the methods, and development of methodology and LRFD parameters for serviceability. The various components are outlined and examples are provided. The need for a multiphase approach in the development of serviceability criteria is presented and its feasibility is demonstrated.


  • The Use of Tactile Sensor Technology for Measuring Soil Stress Distribution

    by Samuel G. Paikowsky, Chris J. Palmer, Lawrence E. Rolwes

    The commonly existing methods of evaluating stress distribution in soils rely on the use of buried or surface mounted load cells. These measurements are difficult to perform and are limited in their ability to capture the stress variation. A relatively new technology, which makes use of flexible, grid-based, tactile pressure sensors, allows to measure stresses at a large number of points in proximity to one another, hence providing a realistic normal stress distribution. Their thin (0.1mm) flexible film overcomes the effect of stiffness variation introduced by rigid load cells and thus allows for measurements that better represent the existing stress conditions. The application of the tactile pressure technology to soils requires adaptation and calibration due to its innovative principle of operation. Examples of work carried out over the past ten years are provided. The presented research addresses three subjects in soil mechanics: (i) the effect of grain size on stress distribution measurement along a boundary with a solid surface, (ii) the pressure dip under the sand heap, and (iii) the contact stresses under a rigid strip footing.


  • Experimental Examination of the Arching Mechanism on the Micro Level

    by Samuel G. Paikowsky, Hsienjen S. Tien

    The arching phenomenon is manifested through the reduction of stresses experienced by underground structures. Arching plays an important role in geotechnical engineering construction, such as excavations, retaining structures, pile groups, tunnel boring machines, culverts and underground facilities. The arching mechanism is intrinsic to granular material/rock mass independent of scale effect. Its fundamental mechanism relates to the ability of discrete units to transfer loads through interaction in a preferable geometry, and thus to bridge between the zone (or point) of load application to the zone (or points) of reaction. Though investigated extensively, very little work has been done to address the fundamental mechanism related to the discrete particles interaction. Testing results of an advanced experimental technique is presented and analyzed. A model of granular material made of photoelastic particles is utilized. The model and the sophisticated image and global data acquisition system allow one to track the development of the arching within ideal granular material during a trap door experiment by following the motion of each particle and the contact forces between the particles. Visual and quantitative analyses are presented demonstrating the relationship between the global arching phenomenon and the particle interaction on the micro-level. The information allows one to observe the changes associated with the arching mechanism and the stress variation resulting from it. Comparisons are possible between DEM and the test results.