Xingkun Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Xingkun Wu has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
Feng Lin
School of Computer Engineering, Nanyang Technological University, 637553, Singapore
5 shared publicationsHe Huang
State Key Laboratory of Modern Optical Instrumentation, Department of Optical Engineering, Zhejiang University, Hangzhou, Zhejiang 310027, China
4 shared publicationsQing Li
State Key Laboratory of Modern Optical Instrumentation, Department of Optical Engineering, Zhejiang University, Hangzhou, Zhejiang 310027, China
4 shared publicationsJian Fu
College of Optical Science and Engineering, Zhejiang University, Hangzhou, China
3 shared publicationsHongmei Zou
State Key Laboratory of Modern Optical Instrumentation, Department of Optical Engineering, Zhejiang University, Hangzhou, Zhejiang 310027, China
2 shared publicationsShijie Chen
State Key Laboratory of Modern Optical Instrumentation, Department of Optical Engineering, Zhejiang University, Hangzhou, Zhejiang 310027, China
2 shared publications
Latest Publications
- Open Access
- 23 February 2021
- Published by MDPI AG in Micromachines
- Vol. 12 (2) , 226
High-Order Fiber Mode Beam Parameter Optimization for Transport and Rotation of Single Cells
Optical tweezers are becoming increasingly important in biomedical applications for the trapping, propelling, binding, and controlled rotation of biological particles. These capabilities enable applications such as cell surgery, microinjections, organelle extraction and modification, and preimplantation genetic diagnosis. In particular, optical fiber-based tweezers are compact, highly flexible, and can be readily integrated into lab-on-a-chip devices. Taking advantage of the beam structure inherent in high-order modes of propagation in optical fiber, LP11, LP21, and LP31 fiber modes can generate structured radial light fields with two or more concentrations in the cross-section of a beam, forming multiple traps for bioparticles with a single optical fiber. In this paper, we report the dynamic modeling and optimization of single cell manipulation with two to six optical traps formed by a single fiber, generated by either spatial light modulation (SLM) or slanted incidence in laser-fiber coupling. In particular, we focus on beam size optimization for arbitrary target cell sizes to enable trapped transport and controlled rotation of a single cell, using a point matching method (PMM) of the T-matrix to compute trapping forces and rotation torque. Finally, we validated these optimized beam sizes experimentally for the LP21 mode. This work provides a new understanding of optimal optical manipulation using high-order fiber modes at the single-cell level.
- 23 February 2021
- Published by MDPI AG in Micromachines
- Vol. 12 (2) , 226
Open AccessHigh-Order Fiber Mode Beam Parameter Optimization for Transport and Rotation of Single Cells
Optical tweezers are becoming increasingly important in biomedical applications for the trapping, propelling, binding, and controlled rotation of biological particles. These capabilities enable applications such as cell surgery, microinjections, organelle extraction and modification, and preimplantation genetic diagnosis. In particular, optical fiber-based tweezers are compact, highly flexible, and can be readily integrated into lab-on-a-chip devices. Taking advantage of the beam structure inherent in high-order modes of propagation in optical fiber, LP11, LP21, and LP31 fiber modes can generate structured radial light fields with two or more concentrations in the cross-section of a beam, forming multiple traps for bioparticles with a single optical fiber. In this paper, we report the dynamic modeling and optimization of single cell manipulation with two to six optical traps formed by a single fiber, generated by either spatial light modulation (SLM) or slanted incidence in laser-fiber coupling. In particular, we focus on beam size optimization for arbitrary target cell sizes to enable trapped transport and controlled rotation of a single cell, using a point matching method (PMM) of the T-matrix to compute trapping forces and rotation torque. Finally, we validated these optimized beam sizes experimentally for the LP21 mode. This work provides a new understanding of optimal optical manipulation using high-order fiber modes at the single-cell level.
- 1 January 2017
- Published by Shanghai Institute of Optics and Fine Mechanics in Chinese Optics Letters
- Vol. 15 (12) , 120602
Real-time measurement of nano-particle size using differential optical phase detection
We demonstrate a size sensing technique for nano-particles using optical differential phase measurement by a dual fiber interferometer through phase-generated carrier (PGC) demodulation. Nano-particle diameters are obtained from the differential phase shift as a result of adding an optical scattering perturbation into two-beam interference. Polystyrene nano-particles with diameters from 200 to 900 nm in a microfluidic channel are detected using this technique to acquire real-time particle diameters. Compared with amplitude sensing with over 10 mW of laser irradiance, particle sizing by PGC phase sensing can be achieved at a laser power as low as 1.18 mW. We further analyze major sources of noise in order to improve the limits of detection. This sensing technique may find a broad range of applications from the real-time selection of biological cell samples to rare cell detection in blood samples for early cancer screening.
- 1 January 2017
- Published by Shanghai Institute of Optics and Fine Mechanics in Chinese Optics Letters
- Vol. 15 (12) , 120602
Real-time measurement of nano-particle size using differential optical phase detection
We demonstrate a size sensing technique for nano-particles using optical differential phase measurement by a dual fiber interferometer through phase-generated carrier (PGC) demodulation. Nano-particle diameters are obtained from the differential phase shift as a result of adding an optical scattering perturbation into two-beam interference. Polystyrene nano-particles with diameters from 200 to 900 nm in a microfluidic channel are detected using this technique to acquire real-time particle diameters. Compared with amplitude sensing with over 10 mW of laser irradiance, particle sizing by PGC phase sensing can be achieved at a laser power as low as 1.18 mW. We further analyze major sources of noise in order to improve the limits of detection. This sensing technique may find a broad range of applications from the real-time selection of biological cell samples to rare cell detection in blood samples for early cancer screening.
- Open Access
- 17 May 2016
- Published by Optica Publishing Group in Optics Express
- Vol. 24 (11) , 11458-11465
Optical micro-particle size detection by phase-generated carrier demodulation
We demonstrate an optical micro-particle size detection technique based on phase sensing by a fiber interferometer through phase-generated carrier (PGC) modulation/demodulation. Particle diameters were resolved from phase shift due to particle-induced optical scattering. Polystyrene nanoparticles, air bubbles and yeast cells in a microfluidic channel were tested using this technique, and particle diameters ranging from 0.7 to 5.5 μm can be resolved in real-time. In comparison with existing amplitude-sensing techniques which require tens of milliwatts of laser irradiance, phase-sensing through PGC can successfully utilize probe laser powers as low as 220 μW to measure the test particle sizes. We further constructed a theoretical model based on phase scattering and PGC demodulation, which obtained good agreement between experimental data and calculated phase shift as a function of particle time-of-flight. This technique may be applied to a wide range of potential applications, ranging from real-time analysis of clinically relevant cell samples, to contamination control of processing fluids used in the semiconductor industry.
- 17 May 2016
- Published by Optica Publishing Group in Optics Express
- Vol. 24 (11) , 11458-11465
Open AccessOptical micro-particle size detection by phase-generated carrier demodulation
We demonstrate an optical micro-particle size detection technique based on phase sensing by a fiber interferometer through phase-generated carrier (PGC) modulation/demodulation. Particle diameters were resolved from phase shift due to particle-induced optical scattering. Polystyrene nanoparticles, air bubbles and yeast cells in a microfluidic channel were tested using this technique, and particle diameters ranging from 0.7 to 5.5 μm can be resolved in real-time. In comparison with existing amplitude-sensing techniques which require tens of milliwatts of laser irradiance, phase-sensing through PGC can successfully utilize probe laser powers as low as 220 μW to measure the test particle sizes. We further constructed a theoretical model based on phase scattering and PGC demodulation, which obtained good agreement between experimental data and calculated phase shift as a function of particle time-of-flight. This technique may be applied to a wide range of potential applications, ranging from real-time analysis of clinically relevant cell samples, to contamination control of processing fluids used in the semiconductor industry.
- 9 September 2015
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 7 (39) , 16504-16507
Efficient subwavelength focusing of light with a long focal depth
We demonstrate an efficient method for far-field subwavelength focusing by a novel two-component axicon structure. Annular beams generated by a fiber axicon are focused using a micro-cone reflector, creating a quasi-Bessel beam with a high convergence angle of up to 40°. A center focal spot diameter of 0.41λ was achieved at a power efficiency of over 40%, with a focal depth of 9λ and a working distance as long as 35 μm. We further demonstrate that experimental knife-edge measurements mapping the beam focal intensity agree with numerical simulations of the structure. This method shows demonstrable promise in overcoming the optical focusing limit of single-element axicons and great potential for use in high tolerance, high-resolution applications in optical systems.
- 9 September 2015
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 7 (39) , 16504-16507
Efficient subwavelength focusing of light with a long focal depth
We demonstrate an efficient method for far-field subwavelength focusing by a novel two-component axicon structure. Annular beams generated by a fiber axicon are focused using a micro-cone reflector, creating a quasi-Bessel beam with a high convergence angle of up to 40°. A center focal spot diameter of 0.41λ was achieved at a power efficiency of over 40%, with a focal depth of 9λ and a working distance as long as 35 μm. We further demonstrate that experimental knife-edge measurements mapping the beam focal intensity agree with numerical simulations of the structure. This method shows demonstrable promise in overcoming the optical focusing limit of single-element axicons and great potential for use in high tolerance, high-resolution applications in optical systems.
- 17 December 2014
- Published by Optica Publishing Group in Applied Optics
- Vol. 53 (36) , 8444-8448
Laser printed fiber microlens for fiber-diode coupling by direct laser writing
A printable microlens on fiber end for coupling between a laser diode to a single-mode fiber (SMF) is demonstrated. The fiber microlens fabricated by the novel technique based on laser direct writing using a quasi-Bessel beam has gained high coupling efficiency, long working distance, and sufficient alignment tolerance. A coupling efficiency of 53.5% was measured for SMF coupling at a working distance of 16 μm. The tolerances for a 1-dB loss increment for translational displacements and angular deviations between the fiber microlens and the laser diode were 2.5 and 1.2 μm, and 2.0 and 5.0 degrees, respectively. The printable fabrication of a microlens on a fiber endface by laser direct writing allows for a batch process to reproduce a multiple microlens with a high consistency in a simple and fast fabrication cycle, with no need of individual fiber loading and unloading.
- 17 December 2014
- Published by Optica Publishing Group in Applied Optics
- Vol. 53 (36) , 8444-8448
Laser printed fiber microlens for fiber-diode coupling by direct laser writing
A printable microlens on fiber end for coupling between a laser diode to a single-mode fiber (SMF) is demonstrated. The fiber microlens fabricated by the novel technique based on laser direct writing using a quasi-Bessel beam has gained high coupling efficiency, long working distance, and sufficient alignment tolerance. A coupling efficiency of 53.5% was measured for SMF coupling at a working distance of 16 μm. The tolerances for a 1-dB loss increment for translational displacements and angular deviations between the fiber microlens and the laser diode were 2.5 and 1.2 μm, and 2.0 and 5.0 degrees, respectively. The printable fabrication of a microlens on a fiber endface by laser direct writing allows for a batch process to reproduce a multiple microlens with a high consistency in a simple and fast fabrication cycle, with no need of individual fiber loading and unloading.
- Open Access
- 1 May 2014
- Published by Optica Publishing Group in Optics Express
- Vol. 22 (9) , 11035-11042
Fabrication of micro-axicons using direct-laser writing
A novel direct-laser writing fabrication process for micro-axicons is demonstrated. A fiber-axicon-generated Bessel beam was utilized to write on UV-curable optical epoxy to form new axicons and axicon arrays, and geometrical parameters of the replicated epoxy axicons were analyzed in terms of both apex angle and proximity of the writing axicons. The shape of the fabricated axicons was demonstrated to be controllable through laser exposure, proximity, and apex angle of the source axicon, and the fabricated axicons are capable of generating a quality Bessel beam with an excellent focusing performance.
- 1 May 2014
- Published by Optica Publishing Group in Optics Express
- Vol. 22 (9) , 11035-11042
Open AccessFabrication of micro-axicons using direct-laser writing
A novel direct-laser writing fabrication process for micro-axicons is demonstrated. A fiber-axicon-generated Bessel beam was utilized to write on UV-curable optical epoxy to form new axicons and axicon arrays, and geometrical parameters of the replicated epoxy axicons were analyzed in terms of both apex angle and proximity of the writing axicons. The shape of the fabricated axicons was demonstrated to be controllable through laser exposure, proximity, and apex angle of the source axicon, and the fabricated axicons are capable of generating a quality Bessel beam with an excellent focusing performance.
- 5 November 2012
- Published by Optica Publishing Group in Optics Express
- Vol. 20 (24) , 26127-26134
Fiber-optic bend sensor using LP_21 mode operation
A novel fiber-optic bending sensor based upon the propagation of LP21 mode is demonstrated. The sensor, comprised of an S-bend fiber on an elastic film, measures LP21 mode specklegram rotation, which increments linearly with bending angle by the stress-optic effect. The sensor is capable of experimentally achieving a sensitivity as high as 4.13 rad/m−1. The theoretical analysis of the sensor, which is a combination of fiber coupled-mode theory and elastic-optic theory, validates the accuracy of the sensor. The sensor is also shown to be temperature-immune, and can detect both bending direction and bending angle with a large dynamic range. Furthermore, the sensor implementation incorporates inexpensive single-mode fiber at 650 nm for few-mode operation, enabling low-loss transmission and compatibility with existing interfaces.
- 5 November 2012
- Published by Optica Publishing Group in Optics Express
- Vol. 20 (24) , 26127-26134
Fiber-optic bend sensor using LP_21 mode operation
A novel fiber-optic bending sensor based upon the propagation of LP21 mode is demonstrated. The sensor, comprised of an S-bend fiber on an elastic film, measures LP21 mode specklegram rotation, which increments linearly with bending angle by the stress-optic effect. The sensor is capable of experimentally achieving a sensitivity as high as 4.13 rad/m−1. The theoretical analysis of the sensor, which is a combination of fiber coupled-mode theory and elastic-optic theory, validates the accuracy of the sensor. The sensor is also shown to be temperature-immune, and can detect both bending direction and bending angle with a large dynamic range. Furthermore, the sensor implementation incorporates inexpensive single-mode fiber at 650 nm for few-mode operation, enabling low-loss transmission and compatibility with existing interfaces.