Mohammad Hoseinpour Gollo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Mohammad Hoseinpour Gollo has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
- Seyed Mohammad Hossein Seyedkashi
Department of Mechanical engineering, University of Birjand, Birjand, Iran
14 shared publications Abbas Hashemi
Faculty of Mechanical Engineering, Shahid Rajaee Teacher Training University, Tehran 16785-136, Iran
6 shared publications- Hassan Moslemi Naeini
Faculty of Mechanical Engineering, Tarbiat Modares University, Tehran, Iran
5 shared publications Amir H. Roohi
Faculty of Industrial and Mechanical Engineering, Qazvin Branch, Islamic Azad University , Qazvin 14115/143, Iran
4 shared publicationsH. Moslemi Naeini
Department of Mechanical Engineering, Faculty of Engineering, Tarbiat Modares University, Tehran, Iran
4 shared publications- Ali Pourkamali Anaraki
Department of Mechanical Engineering, Shahid Rajaee Teacher Training University, Tehran, Iran
3 shared publications
Latest Publications
- Open Access
- 1 January 2026
- Published by National Library of Serbia in Processing and Application of Ceramics
- Vol. 20 (2) , 105-114
Microstructure and mechanical properties of 3Y-TZP ceramics with low $ \mathrm{Al_2}{O_3} $ content for dental applications: Comparing vickers indentation fracture resistance and fracture toughnessAlumina ( \mathrm{Al_2}{O_3} ) addition in 3mol% yttria-stabilised tetragonal zirconia polycrystals (3Y-TZP) enhances dental ceramics’ mechanical properties and microstructure. This study examines the effects of 0, 0.03, 0.06 and 0.09wt.% \mathrm{Al_2}{O_3} addition on Vickers indentation fracture resistance (KIFR) mode I fracture toughness (KIC) and other mechanical characteristics of 3Y-TZP ceramics. The results show that 0.06wt.% \mathrm{Al_2}{O_3} improves relative density, Young’s modulus, Vickers hardness, KIFR and KIC by less than 8%. With higher \mathrm{Al_2}{O_3} content, grain size tends to be reduced. Consistent KIFR trends across various Vickers equations indicate unreliable correlations, with more than 32% discrepancy between KIFR and KIC values from Vickers indentation and Single Edge Laser Notch Beam (SELNB) methods.
- 1 January 2026
- Published by National Library of Serbia in Processing and Application of Ceramics
- Vol. 20 (2) , 105-114
Open AccessMicrostructure and mechanical properties of 3Y-TZP ceramics with low $ \mathrm{Al_2}{O_3} $ content for dental applications: Comparing vickers indentation fracture resistance and fracture toughnessAlumina ( \mathrm{Al_2}{O_3} ) addition in 3mol% yttria-stabilised tetragonal zirconia polycrystals (3Y-TZP) enhances dental ceramics’ mechanical properties and microstructure. This study examines the effects of 0, 0.03, 0.06 and 0.09wt.% \mathrm{Al_2}{O_3} addition on Vickers indentation fracture resistance (KIFR) mode I fracture toughness (KIC) and other mechanical characteristics of 3Y-TZP ceramics. The results show that 0.06wt.% \mathrm{Al_2}{O_3} improves relative density, Young’s modulus, Vickers hardness, KIFR and KIC by less than 8%. With higher \mathrm{Al_2}{O_3} content, grain size tends to be reduced. Consistent KIFR trends across various Vickers equations indicate unreliable correlations, with more than 32% discrepancy between KIFR and KIC values from Vickers indentation and Single Edge Laser Notch Beam (SELNB) methods.
- Open Access
- 22 October 2019
- Published by MDPI AG in Applied Sciences
- Vol. 9 (20) , 4463
Effects of Laser Beam Parameters on Bendability and Microstructure of Stainless Steel in Three-Dimensional Laser Forming
In this study, the effects of beam diameter and hatch spacing between the scanning paths on the bendability and microstructural behavior of an AISI 316 stainless-steel sheet in three-dimensional laser forming were investigated. The strain on the heating lines and that between the scanning tracks were numerically investigated to elucidate the effects of process parameters. The strain on heating lines and that between scanning tracks were numerically investigated. The increase in hatch spacing caused a larger amount of counter bending to be retained in the unaffected areas between the tracks through a process dominated by a temperature gradient mechanism (TGM), and also caused a lower deformation. The formation of small equiaxed dendrite grains instead of coarse and inhomogeneous austenite grains occurred during the process at a larger beam diameter and smaller hatch spacing, which increased the bendability of the material, owing to the decrease in anisotropy in the microstructure. Moreover, the increase in the grain size of the reheated overlap region of the deformed sample led to a higher bendability. Under these conditions, the microhardness was also increased owing to the grain boundary strengthening effect.
- 22 October 2019
- Published by MDPI AG in Applied Sciences
- Vol. 9 (20) , 4463
Open AccessEffects of Laser Beam Parameters on Bendability and Microstructure of Stainless Steel in Three-Dimensional Laser Forming
In this study, the effects of beam diameter and hatch spacing between the scanning paths on the bendability and microstructural behavior of an AISI 316 stainless-steel sheet in three-dimensional laser forming were investigated. The strain on the heating lines and that between the scanning tracks were numerically investigated to elucidate the effects of process parameters. The strain on heating lines and that between scanning tracks were numerically investigated. The increase in hatch spacing caused a larger amount of counter bending to be retained in the unaffected areas between the tracks through a process dominated by a temperature gradient mechanism (TGM), and also caused a lower deformation. The formation of small equiaxed dendrite grains instead of coarse and inhomogeneous austenite grains occurred during the process at a larger beam diameter and smaller hatch spacing, which increased the bendability of the material, owing to the decrease in anisotropy in the microstructure. Moreover, the increase in the grain size of the reheated overlap region of the deformed sample led to a higher bendability. Under these conditions, the microhardness was also increased owing to the grain boundary strengthening effect.
- 5 September 2018
- Published by EDP Sciences in Mechanics & Industry
- Vol. 19 (3) , 303
Application of a new integrated optimization approach in sheet hydroforming process
The purpose of this study is to produce a desired hydroformed product under the optimal pressure profile. To achieve this purpose, a new adaptive optimization approach is proposed based on fuzzy logic control (FLC) integrated with simulated annealing (SA) optimization technique and ANSYS parametric design language (APDL). An intermediate MATLAB code was developed and used to manage data transfer automatically between FLC, SA and APDL, in which there would be no need for any interaction of user/designer during the optimization process execution. This method aims to find the optimal pressure loading profile, prevent wrinkling and necking failures, reduce unsuccessful iterations, and enhance convergence precision. This method is capable of adaptively changing the process parameters in order to reach the optimized values with higher accuracy in a more reasonable time. The results show a good agreement between the proposed optimization approach and experiments. The developed optimization approach is a practical and reliable design tool for industrial production of any symmetric shell cups using hydroforming process.
- 5 September 2018
- Published by EDP Sciences in Mechanics & Industry
- Vol. 19 (3) , 303
Application of a new integrated optimization approach in sheet hydroforming process
The purpose of this study is to produce a desired hydroformed product under the optimal pressure profile. To achieve this purpose, a new adaptive optimization approach is proposed based on fuzzy logic control (FLC) integrated with simulated annealing (SA) optimization technique and ANSYS parametric design language (APDL). An intermediate MATLAB code was developed and used to manage data transfer automatically between FLC, SA and APDL, in which there would be no need for any interaction of user/designer during the optimization process execution. This method aims to find the optimal pressure loading profile, prevent wrinkling and necking failures, reduce unsuccessful iterations, and enhance convergence precision. This method is capable of adaptively changing the process parameters in order to reach the optimized values with higher accuracy in a more reasonable time. The results show a good agreement between the proposed optimization approach and experiments. The developed optimization approach is a practical and reliable design tool for industrial production of any symmetric shell cups using hydroforming process.
- 2 January 2018
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 95 (9-12) , 3919-3928
Forming of closed-cell aluminum foams under thermal loadings: experimental investigation
- 2 January 2018
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 95 (9-12) , 3919-3928
Forming of closed-cell aluminum foams under thermal loadings: experimental investigation
- 1 January 2018
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 18 (1) , 103-113
Determination of critical pressure in analyzing of rupture instability for hydromechanical deep drawing using advanced yield criterion
- 1 January 2018
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 18 (1) , 103-113
Determination of critical pressure in analyzing of rupture instability for hydromechanical deep drawing using advanced yield criterion
- 1 January 2018
- Published by Elsevier in Optics & Laser Technology
- Vol. 98, 121-133
Codification of scan path parameters and development of perimeter scan strategies for 3D bowl-shaped laser forming
- 1 January 2018
- Published by Elsevier in Optics & Laser Technology
- Vol. 98, 121-133
Codification of scan path parameters and development of perimeter scan strategies for 3D bowl-shaped laser forming
- 15 September 2017
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 29 (4)
Optimization of circular scan path to produce bowl shapes in 3D laser forming process
In a three-dimensional laser forming process, laser scan path and scan path parameters are crucial to produce desired shapes. In this manuscript, the optimized perimeter laser scan pattern which results in bowl shapes is presented. Several circular scan paths in circular AISI 304 sheets are considered to produce bowl shapes. Scan path parameters are as follows: (1) continuity or discontinuity of the path; (2) the start point of the path; and (3) the direction of the scan path in each step, including clockwise (CW) and counter clockwise (CCW). Thus, three different continuous circular scan patterns consist of the CW or CCW path with a similar angular location, mixed CW and CCW paths with different start points and the CW or CCW scan paths with different start points are investigated. Besides, two discontinuous circular paths, including the same CW or CCW direction, and mixed CW and CCW directions are studied. Comparison between different proposed scan patterns is carried out based on three criteria considered, that is, the average height of the perimeter points, the edge distortion, and the standard deviation of the final product. The results show that the continuous CW or CCW scan path with different start points is the optimized circular scan pattern. In addition, further experimentations using the presented results in this manuscript illustrate the continuous circular path with the same scan direction and a 90° angular step leads to optimum desired bowl shapes.
- 15 September 2017
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 29 (4)
Optimization of circular scan path to produce bowl shapes in 3D laser forming process
In a three-dimensional laser forming process, laser scan path and scan path parameters are crucial to produce desired shapes. In this manuscript, the optimized perimeter laser scan pattern which results in bowl shapes is presented. Several circular scan paths in circular AISI 304 sheets are considered to produce bowl shapes. Scan path parameters are as follows: (1) continuity or discontinuity of the path; (2) the start point of the path; and (3) the direction of the scan path in each step, including clockwise (CW) and counter clockwise (CCW). Thus, three different continuous circular scan patterns consist of the CW or CCW path with a similar angular location, mixed CW and CCW paths with different start points and the CW or CCW scan paths with different start points are investigated. Besides, two discontinuous circular paths, including the same CW or CCW direction, and mixed CW and CCW directions are studied. Comparison between different proposed scan patterns is carried out based on three criteria considered, that is, the average height of the perimeter points, the edge distortion, and the standard deviation of the final product. The results show that the continuous CW or CCW scan path with different start points is the optimized circular scan pattern. In addition, further experimentations using the presented results in this manuscript illustrate the continuous circular path with the same scan direction and a 90° angular step leads to optimum desired bowl shapes.
- 7 September 2017
- Published by Springer Nature in Metals and Materials International
- Vol. 23 (5) , 865-876
Evolution of microstructure and mechanical properties of SUS430/C11000/SUS430 composites during the laser-forming process
- 7 September 2017
- Published by Springer Nature in Metals and Materials International
- Vol. 23 (5) , 865-876
Evolution of microstructure and mechanical properties of SUS430/C11000/SUS430 composites during the laser-forming process
- 4 September 2017
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 39 (12) , 5181-5194
Theoretical and experimental investigation of hydro-mechanical deep drawing of hemi-prolate spheroid cups
- 4 September 2017
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 39 (12) , 5181-5194
Theoretical and experimental investigation of hydro-mechanical deep drawing of hemi-prolate spheroid cups
- 31 January 2017
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 39 (10) , 4011-4020
A new simulation-based metaheuristic approach in optimization of bilayer composite sheet hydroforming
- 31 January 2017
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 39 (10) , 4011-4020
A new simulation-based metaheuristic approach in optimization of bilayer composite sheet hydroforming