Nikolay Alekseev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Nikolay Alekseev has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Andrey V. Samokhin
Baikov Institute of Metallurgy and Materials Science, Russian Academy of Sciences (IMET RAS), Moscow, Russia
10 shared publications - Alexey A. Dorofeev
Baikov Institute of Metallurgy and Materials Science of the Russian Academy of Sciences, 49, Leninskiy Prosp., 119334 Moscow, Russia
4 shared publications - Andrey Fadeev
Baikov Institute of Metallurgy and Materials Science, Russian Academy of Sciences (IMET RAS), Moscow, Russia
4 shared publications - Alexander V. Vodopyanov
Institute of Applied Physics, Russian Academy of Sciences, Nizhny Novgorod, Russia
3 shared publications - Mikhail A. Sinayskiy
Baikov Institute of Metallurgy and Materials Science of the Russian Academy of Sciences
3 shared publications - Mikhail Yu. Gryaznov
Nizhni Novgorod University
2 shared publications
Latest Publications
- 1 June 2025
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 16 (3) , 618-629
Selective Laser Melting of Plasma Spheroidized Tungsten Powder with a Fine Crystalline Particle Structure
The paper demonstrates for the first time the possibility of using an unalloyed tungsten powder with a spherical particle shape from 5 to 45 μm with a grain size of 0.5 to 2 μm obtained using plasma chemical synthesis, granulation, and spheroidization technologies to create products using additive technologies. The influence of the technological parameters of the selective laser melting (SLM) process on the physicomechanical characteristics and microstructure of test samples made of unalloyed tungsten powder has been studied. It is shown that the SLM parameters have a significant effect on the formation of the microstructure of test samples. It has been experimentally proved that, at optimal parameters of the SLM process, a homogeneous equiaxed microstructure with an average grain size of about 10 μm is formed in the samples. It was found that the maximum value of the Vickers hardness of the studied SLM samples of unalloyed tungsten is 310 HV10; the maximum value of microhardness is 4.1 GPa. The maximum density value of the obtained samples is 19.1 g/cm3 (relative density is 99.2%). At the same time, it was found that a high crystallization rate and a large temperature gradient during the SLM process lead to the formation of microcracks and micropores in the structure of massive samples, which greatly complicates the technological task of obtaining high-density defect-free bulk products from unalloyed tungsten.
- 1 June 2025
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 16 (3) , 618-629
Selective Laser Melting of Plasma Spheroidized Tungsten Powder with a Fine Crystalline Particle Structure
The paper demonstrates for the first time the possibility of using an unalloyed tungsten powder with a spherical particle shape from 5 to 45 μm with a grain size of 0.5 to 2 μm obtained using plasma chemical synthesis, granulation, and spheroidization technologies to create products using additive technologies. The influence of the technological parameters of the selective laser melting (SLM) process on the physicomechanical characteristics and microstructure of test samples made of unalloyed tungsten powder has been studied. It is shown that the SLM parameters have a significant effect on the formation of the microstructure of test samples. It has been experimentally proved that, at optimal parameters of the SLM process, a homogeneous equiaxed microstructure with an average grain size of about 10 μm is formed in the samples. It was found that the maximum value of the Vickers hardness of the studied SLM samples of unalloyed tungsten is 310 HV10; the maximum value of microhardness is 4.1 GPa. The maximum density value of the obtained samples is 19.1 g/cm3 (relative density is 99.2%). At the same time, it was found that a high crystallization rate and a large temperature gradient during the SLM process lead to the formation of microcracks and micropores in the structure of massive samples, which greatly complicates the technological task of obtaining high-density defect-free bulk products from unalloyed tungsten.
- 3 June 2024
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 15 (3) , 779-788
W–C–Co Composite Nanopowder Treatment in Microwave Electromagnetic Field
—Experiments were carried out on the treatment of nanopowders of the W–C–Co system obtained by plasma-chemical synthesis in a microwave electromagnetic field with a frequency of 2.45 and 24 GHz in different gas media. The effect of treatment time, power input, and carbon content in the treated nanopowder on the yield of tungsten monocarbide WC was investigated.
- 3 June 2024
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 15 (3) , 779-788
W–C–Co Composite Nanopowder Treatment in Microwave Electromagnetic Field
—Experiments were carried out on the treatment of nanopowders of the W–C–Co system obtained by plasma-chemical synthesis in a microwave electromagnetic field with a frequency of 2.45 and 24 GHz in different gas media. The effect of treatment time, power input, and carbon content in the treated nanopowder on the yield of tungsten monocarbide WC was investigated.
- 1 June 2023
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 14 (3) , 884-895
Investigation of Nanopowder Granulation in W–Ni–Fe Systems Using Spray-Drying Approach
A method is examined to obtain nanopowder microgranules in the W–Ni–Fe system (VNZh-90 composition) using spray-drying suspension based on composite nanoparticles obtained by plasma-chemical synthesis. The operating parameters of the Buchi Mini spray Dryer B-290 laboratory installation equipped with an ultrasonic nozzle are determined through experiments. These parameters ensure producing VNZh‑90 nanopowder microgranules with required output fraction of 25–63 µm at the level of 65%. The size and morphology of granules is established to be dependent on the choice of dispersion medium, on the concentration of the dispersed phase, and on the organic binder in the suspension. The effect of consumption of the suspension during spray drying is estimated in generating granules of the fraction of 25–63 µm. The experimental sample of nanopowder microgranules is tested during plasma spheroidization.
- 1 June 2023
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 14 (3) , 884-895
Investigation of Nanopowder Granulation in W–Ni–Fe Systems Using Spray-Drying Approach
A method is examined to obtain nanopowder microgranules in the W–Ni–Fe system (VNZh-90 composition) using spray-drying suspension based on composite nanoparticles obtained by plasma-chemical synthesis. The operating parameters of the Buchi Mini spray Dryer B-290 laboratory installation equipped with an ultrasonic nozzle are determined through experiments. These parameters ensure producing VNZh‑90 nanopowder microgranules with required output fraction of 25–63 µm at the level of 65%. The size and morphology of granules is established to be dependent on the choice of dispersion medium, on the concentration of the dispersed phase, and on the organic binder in the suspension. The effect of consumption of the suspension during spray drying is estimated in generating granules of the fraction of 25–63 µm. The experimental sample of nanopowder microgranules is tested during plasma spheroidization.
- Open Access
Method of W-Ni-Fe Composite Spherical Powder Production and the Possibility of Its Application in Selective Laser Melting Technology
For the first time, a powder of W-5Ni-2Fe composition with spherical particles from 15 to 50 microns and a tungsten grain size from 0.5 to 3 microns was obtained using a new technological approach, developed by the authors, based on plasma spheroidization of powder granules made from nanoparticles synthesized in a plasma chemical process. The possibility of using the obtained spheroidized powder W-5Ni-2Fe in the process of selective laser melting (SLM) has been proved. The microstructure, physical, and mechanical characteristics of experimental samples made using SLM technology from the produced W-5Ni-2Fe powder have been studied. The results of the performed studies have shown that the microstructure of experimental samples is extremely dependent on the parameters of the SLM process. The precise choice of the SLM process mode made it possible to obtain a homogeneous structure of experimental samples of tungsten heavy alloy (WHA), with a tungsten grain size of about 1–2 microns, which is much smaller than the tungsten grain size in traditional heavy alloys. This creates prerequisites for increasing the strength characteristics of parts of complex shapes made by the SLM method from such powders. The maximum values of density and hardness of experimental samples obtained in the conducted studies are not worse than the values of samples obtained using traditional liquid-phase sintering technology. It is determined that the main problem of SLM powder W-5Ni-2Fe during investigation is the heterogeneity of the microstructure of massive samples and the formation of micropores and microcracks.
Open AccessMethod of W-Ni-Fe Composite Spherical Powder Production and the Possibility of Its Application in Selective Laser Melting Technology
For the first time, a powder of W-5Ni-2Fe composition with spherical particles from 15 to 50 microns and a tungsten grain size from 0.5 to 3 microns was obtained using a new technological approach, developed by the authors, based on plasma spheroidization of powder granules made from nanoparticles synthesized in a plasma chemical process. The possibility of using the obtained spheroidized powder W-5Ni-2Fe in the process of selective laser melting (SLM) has been proved. The microstructure, physical, and mechanical characteristics of experimental samples made using SLM technology from the produced W-5Ni-2Fe powder have been studied. The results of the performed studies have shown that the microstructure of experimental samples is extremely dependent on the parameters of the SLM process. The precise choice of the SLM process mode made it possible to obtain a homogeneous structure of experimental samples of tungsten heavy alloy (WHA), with a tungsten grain size of about 1–2 microns, which is much smaller than the tungsten grain size in traditional heavy alloys. This creates prerequisites for increasing the strength characteristics of parts of complex shapes made by the SLM method from such powders. The maximum values of density and hardness of experimental samples obtained in the conducted studies are not worse than the values of samples obtained using traditional liquid-phase sintering technology. It is determined that the main problem of SLM powder W-5Ni-2Fe during investigation is the heterogeneity of the microstructure of massive samples and the formation of micropores and microcracks.
- Open Access
Preparation of W-C-Co Composite Micropowder with Spherical Shaped Particles Using Plasma Technologies
The possibility of obtaining composite micropowders of the W-C-Co system with a spherical particle shape having a submicron/nanoscale internal structure was experimentally confirmed. In the course of work carried out, W-C-Co system nanopowders with the average particle size of approximately 50 nm were produced by plasma-chemical synthesis. This method resulted in the uniform distribution of W, Co and C among the nanoparticles of the powder in the nanometer scale range. Dense microgranules with an average size of 40 microns were obtained from the nanopowders by spray drying. The spherical micropowders with an average particle size of 20 microns were received as a result of plasma treatment of 25.36 microns microgranule fraction. The spherical particles obtained in the experiments had a predominantly dense microstructure and had no internal cavities. The influence of plasma treatment process parameters on dispersity, phase, and chemical composition of spherical micropowders and powder particles microstructure has been established.
Open AccessPreparation of W-C-Co Composite Micropowder with Spherical Shaped Particles Using Plasma Technologies
The possibility of obtaining composite micropowders of the W-C-Co system with a spherical particle shape having a submicron/nanoscale internal structure was experimentally confirmed. In the course of work carried out, W-C-Co system nanopowders with the average particle size of approximately 50 nm were produced by plasma-chemical synthesis. This method resulted in the uniform distribution of W, Co and C among the nanoparticles of the powder in the nanometer scale range. Dense microgranules with an average size of 40 microns were obtained from the nanopowders by spray drying. The spherical micropowders with an average particle size of 20 microns were received as a result of plasma treatment of 25.36 microns microgranule fraction. The spherical particles obtained in the experiments had a predominantly dense microstructure and had no internal cavities. The influence of plasma treatment process parameters on dispersity, phase, and chemical composition of spherical micropowders and powder particles microstructure has been established.
- 1 May 2021
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 12 (3) , 735-739
Tungsten Carbide Nanopowder Synthesis under the Influence of Microwave Electromagnetic Radiation on a W–C System Nanocomposite Produced in a Thermal Plasma
The effect of processing multicomponent nanopowders of the W–C system, obtained by plasma-chemical synthesis, in microwave fields with a frequency of 2.45 and 24 GHz generated using a magnetron and gyrotron, respectively, is studied experimentally. It is established that microwave processing results in the formation of nanosized particles of tungsten carbide WC. The influence of processing time on the phase, disperse, and chemical compositions of nanopowders is investigated.
- 1 May 2021
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 12 (3) , 735-739
Tungsten Carbide Nanopowder Synthesis under the Influence of Microwave Electromagnetic Radiation on a W–C System Nanocomposite Produced in a Thermal Plasma
The effect of processing multicomponent nanopowders of the W–C system, obtained by plasma-chemical synthesis, in microwave fields with a frequency of 2.45 and 24 GHz generated using a magnetron and gyrotron, respectively, is studied experimentally. It is established that microwave processing results in the formation of nanosized particles of tungsten carbide WC. The influence of processing time on the phase, disperse, and chemical compositions of nanopowders is investigated.
- 1 January 2021
- Published by Ioffe Institute Russian Academy of Sciences in Письма в журнал технической физики
- Vol. 47 (5) , 51
Получение высокодисперсного порошка монооксида олова методом испарения-конденсации при нагреве сфокусированным излучением субтерагерцевого гиротрона
A method of obtaining highly dispersed tin (II) oxide (SnO) powder by the evaporation-condensation method was investigated when the initial material was heated by focused radiation of a subterahertz gyrotron with a frequency of 0.26 THz and a power of 1 kW. The process was carried out with a purge with nitrogen inert with respect to SnO. A powder with a SnO weight content of 92% was obtained. The specific surface was 7.20 m2/g, which corresponds to an average particle size of 130 nm. The characteristics of the obtained powder are analyzed. The applicability of the experimental setup for the production of nanopowders from compounds requiring special gas conditions during the evaporation-condensation process has been demonstrated.
- 1 January 2021
- Published by Ioffe Institute Russian Academy of Sciences in Письма в журнал технической физики
- Vol. 47 (5) , 51
Получение высокодисперсного порошка монооксида олова методом испарения-конденсации при нагреве сфокусированным излучением субтерагерцевого гиротрона
A method of obtaining highly dispersed tin (II) oxide (SnO) powder by the evaporation-condensation method was investigated when the initial material was heated by focused radiation of a subterahertz gyrotron with a frequency of 0.26 THz and a power of 1 kW. The process was carried out with a purge with nitrogen inert with respect to SnO. A powder with a SnO weight content of 92% was obtained. The specific surface was 7.20 m2/g, which corresponds to an average particle size of 130 nm. The characteristics of the obtained powder are analyzed. The applicability of the experimental setup for the production of nanopowders from compounds requiring special gas conditions during the evaporation-condensation process has been demonstrated.
- 1 May 2020
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 11 (3) , 579-585
Spheroidization of Fe-Based Powders in Plasma Jet of DC Arc Plasma Torch and Application of These Powders in Selective Laser Melting
Spheroidization of Fe and steel powders in a plasma stream of an DC arc plasma torch is investigated. The possibility of obtaining a product with a spherical particle content of up to 100% is established. The fluidity of the best samples of obtained powder is 13–20 s with a fluidity of the feedstock of 39 s. The bulk density of the initial powder (3.05 g/cm3) during the plasma treatment increases to 4.1–4.4 g/cm3. The nanofraction content in spheroidized powders varied from 0 to 75 wt % and it depends mainly on the enthalpy of the plasma stream, consumption of raw materials, and the organization of the flow of the plasma-forming gas in the discharge channel of the plasma torch. It is established that Fe powders spheroidized in plasma can be used in selective laser melting technology to obtain compact samples whose density reaches 7.86 g/cm3.
- 1 May 2020
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 11 (3) , 579-585
Spheroidization of Fe-Based Powders in Plasma Jet of DC Arc Plasma Torch and Application of These Powders in Selective Laser Melting
Spheroidization of Fe and steel powders in a plasma stream of an DC arc plasma torch is investigated. The possibility of obtaining a product with a spherical particle content of up to 100% is established. The fluidity of the best samples of obtained powder is 13–20 s with a fluidity of the feedstock of 39 s. The bulk density of the initial powder (3.05 g/cm3) during the plasma treatment increases to 4.1–4.4 g/cm3. The nanofraction content in spheroidized powders varied from 0 to 75 wt % and it depends mainly on the enthalpy of the plasma stream, consumption of raw materials, and the organization of the flow of the plasma-forming gas in the discharge channel of the plasma torch. It is established that Fe powders spheroidized in plasma can be used in selective laser melting technology to obtain compact samples whose density reaches 7.86 g/cm3.
- Open Access
- 5 December 2017
- Published by Springer Nature
- p. 469-479
Nanopowders Synthesis of Oxygen-Free Titanium Compounds—Nitride, Carbonitride, and Carbide in a Plasma Reactor
- 5 December 2017
- Published by Springer Nature
- p. 469-479
Open AccessNanopowders Synthesis of Oxygen-Free Titanium Compounds—Nitride, Carbonitride, and Carbide in a Plasma Reactor
- 1 September 2015
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 6 (5) , 528-535
Synthesis of nanoscale zirconium dioxide powders and composites on their basis in thermal DC Plasma
- 1 September 2015
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 6 (5) , 528-535
Synthesis of nanoscale zirconium dioxide powders and composites on their basis in thermal DC Plasma