YHYong Seok Hwang

Yong Seok Hwang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yong Seok Hwang has a total of 1 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Superheating and melting within aluminum core–oxide shell nanoparticles for a broad range of heating rates: multiphysics phase field modeling

    by Yong Seok Hwang, Valery I. Levitas

    The external surface of metallic particles is usually covered by a thin and strong oxide shell, which significantly affects superheating and melting of particles. The effects of geometric parameters and heating rate on characteristic melting and superheating temperatures and melting behavior of aluminum nanoparticles covered by an oxide shell were studied numerically. For this purpose, the multiphysics model that includes the phase field model for surface melting, a dynamic equation of motion, a mechanical model for stress and strain simulations, interface and surface stresses, and the thermal conduction model including thermoelastic and thermo-phase transformation coupling as well as transformation dissipation rate was formulated. Several nontrivial phenomena were revealed. In comparison with a bare particle, the pressure generated in a core due to different thermal expansions of the core and shell and transformation volumetric expansion during melting, increases melting temperatures with the Clausius–Clapeyron factor of 60 K GPa−1. For the heating rates Q ≤ 109 K s−1, melting temperatures (surface and bulk start and finish melting temperatures, and maximum superheating temperature) are independent of Q. For Q ≥ 1012 K s−1, increasing Q generally increases melting temperatures and temperature for the shell fracture. Unconventional effects start for Q ≥ 1012 K s−1 due to kinetic superheating combined with heterogeneous melting and geometry. The obtained results are applied to shed light on the initial stage of the melt-dispersion-mechanism of the reaction of Al nanoparticles. Various physical phenomena that promote or suppress melting and affect melting temperatures and temperature of the shell fracture for different heating-rate ranges are summarized in the corresponding schemes.


  • Coupled phase field, heat conduction, and elastodynamic simulations of kinetic superheating and nanoscale melting of aluminum nanolayer irradiated by picosecond laser

    by Yong Seok Hwang, Valery I. Levitas

    An advanced continuum model for nanoscale melting and kinetic superheating of an aluminum nanolayer irradiated by a picosecond laser is formulated. Barrierless nucleation of surface premelting and melting occurs, followed by a propagation of two solid–melt interfaces toward each other and their collision. For a slow heating rate of Q = 0.015 K ps−1 melting occurs at the equilibrium melting temperature under uniaxial strain conditions Tε eq = 898.1 K (i.e., below equilibrium melting temperature Teq = 933.67 K) and corresponding biaxial stresses, which relax during melting. For a high heating rate of Q = 0.99–84 K ps−1, melting occurs significantly above Teq. Surprisingly, an increase in heating rate leads to temperature reduction at the 3 nm wide moving interfaces due to fast absorption of the heat of fusion. A significant, rapid temperature drop (100–500 K, even below melting temperature) at the very end of melting is revealed, which is caused by the collision of two finite-width interfaces and accelerated melting in about the 5 nm zone. For Q = 25–84 K ps−1, standing elastic stress waves are observed in a solid with nodal points at the moving solid–melt interfaces, which, however, do not have a profound effect on melting time or temperatures. When surface melting is suppressed, barrierless bulk melting occurs in the entire sample, and elastodynamic effects are more important. Good correspondence with published, experimentally-determined melting time is found for a broad range of heating rates. Similar approaches can be applied to study various phase transformations in different materials and nanostructures under high heating rates.