Ramin Mirzazadeh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ramin Mirzazadeh has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Stefano Mariani
Department of Civil and Environmental Engineering, Politecnico di Milano, piazza Leonardo da Vinci 32, 20133 Milano, Italy
8 shared publications - Saeed Eftekhar Azam
Department of Civil and Environmental Engineering, University of New Hampshire, Durham, NH 03824, USA
3 shared publications - Aldo Ghisi
Department of Civil and Environmental Engineering, Politecnico di Milano, piazza Leonardo da Vinci 32, 20133 Milano, Italy
2 shared publications Eelco Jansen
Institute of Structural Analysis, Leibniz Universität Hannover, Appelstrasse 9A, 30167, Germany
1 shared publicationM. De Fazio
STMicroelectronics, Advanced System Technology, Via C. Olivetti 2, 20041 Agrate Brianza, Italy
1 shared publication- Marco De Fazio
STMicroelectronics
1 shared publication
Latest Publications
- Open Access
- 19 April 2019
- Published by MDPI AG in Micromachines
- Vol. 10 (4) , 263
Estimation of Air Damping in Out-of-Plane Comb-Drive Actuators
The development of new compliant resonant microsystems and the trend towards further miniaturization have recently raised the issue of the accuracy and reliability of computational tools for the estimation of fluid damping. Focusing on electrostatically actuated torsional micro-mirrors, a major dissipation contribution is linked to the constrained flow of air at comb fingers. In the case of large tilting angles of the mirror plate, within a period of oscillation the geometry of the air domain at comb-drives gets largely distorted, and the dissipation mechanism is thereby affected. In this communication, we provide an appraisal of simple analytical solutions to estimate the dissipation in the ideal case of air flow between infinite plates, at atmospheric pressure. The results of numerical simulations are also reported to assess the effect on damping of the finite size of actual geometries.
- 19 April 2019
- Published by MDPI AG in Micromachines
- Vol. 10 (4) , 263
Open AccessEstimation of Air Damping in Out-of-Plane Comb-Drive Actuators
The development of new compliant resonant microsystems and the trend towards further miniaturization have recently raised the issue of the accuracy and reliability of computational tools for the estimation of fluid damping. Focusing on electrostatically actuated torsional micro-mirrors, a major dissipation contribution is linked to the constrained flow of air at comb fingers. In the case of large tilting angles of the mirror plate, within a period of oscillation the geometry of the air domain at comb-drives gets largely distorted, and the dissipation mechanism is thereby affected. In this communication, we provide an appraisal of simple analytical solutions to estimate the dissipation in the ideal case of air flow between infinite plates, at atmospheric pressure. The results of numerical simulations are also reported to assess the effect on damping of the finite size of actual geometries.
- Open Access
Mechanical Characterization of Polysilicon MEMS: A Hybrid TMCMC/POD-Kriging Approach
Microscale uncertainties related to the geometry and morphology of polycrystalline silicon films, constituting the movable structures of micro electro-mechanical systems (MEMS), were investigated through a joint numerical/experimental approach. An on-chip testing device was designed and fabricated to deform a compliant polysilicon beam. In previous studies, we showed that the scattering in the input–output characteristics of the device can be properly described only if statistical features related to the morphology of the columnar polysilicon film and to the etching process adopted to release the movable structure are taken into account. In this work, a high fidelity finite element model of the device was used to feed a transitional Markov chain Monte Carlo (TMCMC) algorithm for the estimation of the unknown parameters governing the aforementioned statistical features. To reduce the computational cost of the stochastic analysis, a synergy of proper orthogonal decomposition (POD) and kriging interpolation was adopted. Results are reported for a batch of nominally identical tested devices, in terms of measurement error-affected probability distributions of the overall Young’s modulus of the polysilicon film and of the overetch depth.
Open AccessMechanical Characterization of Polysilicon MEMS: A Hybrid TMCMC/POD-Kriging Approach
Microscale uncertainties related to the geometry and morphology of polycrystalline silicon films, constituting the movable structures of micro electro-mechanical systems (MEMS), were investigated through a joint numerical/experimental approach. An on-chip testing device was designed and fabricated to deform a compliant polysilicon beam. In previous studies, we showed that the scattering in the input–output characteristics of the device can be properly described only if statistical features related to the morphology of the columnar polysilicon film and to the etching process adopted to release the movable structure are taken into account. In this work, a high fidelity finite element model of the device was used to feed a transitional Markov chain Monte Carlo (TMCMC) algorithm for the estimation of the unknown parameters governing the aforementioned statistical features. To reduce the computational cost of the stochastic analysis, a synergy of proper orthogonal decomposition (POD) and kriging interpolation was adopted. Results are reported for a batch of nominally identical tested devices, in terms of measurement error-affected probability distributions of the overall Young’s modulus of the polysilicon film and of the overetch depth.
- Open Access
- 30 January 2018
- Published by MDPI AG in Micromachines
- Vol. 9 (2) , 53
Statistical Investigation of the Mechanical and Geometrical Properties of Polysilicon Films through On-Chip Tests
In this work, we provide a numerical/experimental investigation of the micromechanics-induced scattered response of a polysilicon on-chip MEMS testing device, whose moving structure is constituted by a slender cantilever supporting a massive perforated plate. The geometry of the cantilever was specifically designed to emphasize the micromechanical effects, in compliance with the process constraints. To assess the effects of the variability of polysilicon morphology and of geometrical imperfections on the experimentally observed nonlinear sensor response, we adopt statistical Monte Carlo analyses resting on a coupled electromechanical finite element model of the device. For each analysis, the polysilicon morphology was digitally built through a Voronoi tessellation of the moving structure, whose geometry was in turn varied by sampling out of a uniform probability density function the value of the over-etch, considered as the main source of geometrical imperfections. The comparison between the statistics of numerical and experimental results is adopted to assess the relative significance of the uncertainties linked to variations in the micro-fabrication process, and the mechanical film properties due to the polysilicon morphology.
- 30 January 2018
- Published by MDPI AG in Micromachines
- Vol. 9 (2) , 53
Open AccessStatistical Investigation of the Mechanical and Geometrical Properties of Polysilicon Films through On-Chip Tests
In this work, we provide a numerical/experimental investigation of the micromechanics-induced scattered response of a polysilicon on-chip MEMS testing device, whose moving structure is constituted by a slender cantilever supporting a massive perforated plate. The geometry of the cantilever was specifically designed to emphasize the micromechanical effects, in compliance with the process constraints. To assess the effects of the variability of polysilicon morphology and of geometrical imperfections on the experimentally observed nonlinear sensor response, we adopt statistical Monte Carlo analyses resting on a coupled electromechanical finite element model of the device. For each analysis, the polysilicon morphology was digitally built through a Voronoi tessellation of the moving structure, whose geometry was in turn varied by sampling out of a uniform probability density function the value of the over-etch, considered as the main source of geometrical imperfections. The comparison between the statistics of numerical and experimental results is adopted to assess the relative significance of the uncertainties linked to variations in the micro-fabrication process, and the mechanical film properties due to the polysilicon morphology.
- Open Access
- 12 August 2017
- Published by MDPI AG in Micromachines
- Vol. 8 (8) , 248
Uncertainty Quantification of Microstructure—Governed Properties of Polysilicon MEMS
In this paper, we investigate the stochastic effects of the microstructure of polysilicon films on the overall response of microelectromechanical systems (MEMS). A device for on-chip testing has been purposely designed so as to maximize, in compliance with the production process, its sensitivity to fluctuations of the microstructural properties; as a side effect, its sensitivity to geometrical imperfections linked to the etching process has also been enhanced. A reduced-order, coupled electromechanical model of the device is developed and an identification procedure, based on a genetic algorithm, is finally adopted to tune the parameters ruling microstructural and geometrical uncertainties. Besides an initial geometrical imperfection that can be considered specimen-dependent due to its scattering, the proposed procedure has allowed identifying an average value of the effective polysilicon Young’s modulus amounting to 140 GPa, and of the over-etch depth with respect to the target geometry layout amounting to m. The procedure has been therefore shown to be able to assess how the studied stochastic effects are linked to the scattering of the measured input–output transfer function of the device under standard working conditions. With a continuous trend in miniaturization induced by the mass production of MEMS, this study can provide information on how to handle the foreseen growth of such scattering.- 12 August 2017
- Published by MDPI AG in Micromachines
- Vol. 8 (8) , 248
Open AccessUncertainty Quantification of Microstructure—Governed Properties of Polysilicon MEMS
In this paper, we investigate the stochastic effects of the microstructure of polysilicon films on the overall response of microelectromechanical systems (MEMS). A device for on-chip testing has been purposely designed so as to maximize, in compliance with the production process, its sensitivity to fluctuations of the microstructural properties; as a side effect, its sensitivity to geometrical imperfections linked to the etching process has also been enhanced. A reduced-order, coupled electromechanical model of the device is developed and an identification procedure, based on a genetic algorithm, is finally adopted to tune the parameters ruling microstructural and geometrical uncertainties. Besides an initial geometrical imperfection that can be considered specimen-dependent due to its scattering, the proposed procedure has allowed identifying an average value of the effective polysilicon Young’s modulus amounting to 140 GPa, and of the over-etch depth with respect to the target geometry layout amounting to m. The procedure has been therefore shown to be able to assess how the studied stochastic effects are linked to the scattering of the measured input–output transfer function of the device under standard working conditions. With a continuous trend in miniaturization induced by the mass production of MEMS, this study can provide information on how to handle the foreseen growth of such scattering. - 1 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Uncertainty quantification in polysilicon MEMS through on-chip testing and reduced-order modelling
In this paper, micro-scale uncertainties affecting the behaviour of microelectromechanical systems (MEMS) are investigated through a mixed numerical/experimental approach. An on-chip test device has been designed and fabricated using standard MEMS fabrication techniques, to deform a (microstructured) polysilicon beam. To interpret the experimental data and also the relevant scatterings in the system response, a high fidelity, parametric finite element (FE) model of the device is developed in ANSYS. Uncertainties in the parameters governing the polysilicon mechanical properties and the geometry of the movable structure are estimated through an inverse analysis. To systematically quantify the uncertainty levels within the realm of a cost-effective statistical analysis, a model order reduction technique based on a synergy of proper orthogonal decomposition (POD) and Kriging interpolation is proposed. The resulting reduced order model is finally fed into a transitional Markov chain Monte Carlo (TMCMC) algorithm for the estimation of the unknown parameters.
- 1 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Uncertainty quantification in polysilicon MEMS through on-chip testing and reduced-order modelling
In this paper, micro-scale uncertainties affecting the behaviour of microelectromechanical systems (MEMS) are investigated through a mixed numerical/experimental approach. An on-chip test device has been designed and fabricated using standard MEMS fabrication techniques, to deform a (microstructured) polysilicon beam. To interpret the experimental data and also the relevant scatterings in the system response, a high fidelity, parametric finite element (FE) model of the device is developed in ANSYS. Uncertainties in the parameters governing the polysilicon mechanical properties and the geometry of the movable structure are estimated through an inverse analysis. To systematically quantify the uncertainty levels within the realm of a cost-effective statistical analysis, a model order reduction technique based on a synergy of proper orthogonal decomposition (POD) and Kriging interpolation is proposed. The resulting reduced order model is finally fed into a transitional Markov chain Monte Carlo (TMCMC) algorithm for the estimation of the unknown parameters.
- Open Access
- 14 November 2016
- Published by MDPI AG in Proceedings
- Vol. 1 (2) , 39
Assessment of Micromechanically-Induced Uncertainties in the Electromechanical Response of MEMS Devices
Microelectromechanical systems (MEMS) have been already successfully commercialized for around 20 years. The design of novel MEMS sensors currently targets two important features: smaller dimensions and higher reliability. As the characteristic size of the mechanical components of the devices decreases, uncertainties in the mechanical and geometrical properties induced by the microfabrication process become more and more important. To address these issues, an on-chip testing device has been proposed to avoid any visual inspection for the read-out. The electromechanical responses of ten nominally identical specimens have been recorded, and experimental data have shown a significant scattering due to the presence of relevant uncertainty sources. To interpret the response of the device, an analytical reduced-order model of the whole device has been developed. A genetic algorithm has then been adopted to identify features of the mechanical and geometrical uncertainties in the batch of test structures.
- 14 November 2016
- Published by MDPI AG in Proceedings
- Vol. 1 (2) , 39
Open AccessAssessment of Micromechanically-Induced Uncertainties in the Electromechanical Response of MEMS Devices
Microelectromechanical systems (MEMS) have been already successfully commercialized for around 20 years. The design of novel MEMS sensors currently targets two important features: smaller dimensions and higher reliability. As the characteristic size of the mechanical components of the devices decreases, uncertainties in the mechanical and geometrical properties induced by the microfabrication process become more and more important. To address these issues, an on-chip testing device has been proposed to avoid any visual inspection for the read-out. The electromechanical responses of ten nominally identical specimens have been recorded, and experimental data have shown a significant scattering due to the presence of relevant uncertainty sources. To interpret the response of the device, an analytical reduced-order model of the whole device has been developed. A genetic algorithm has then been adopted to identify features of the mechanical and geometrical uncertainties in the batch of test structures.
- Open Access
Micromechanical Characterization of Polysilicon Films through On-Chip Tests
When the dimensions of polycrystalline structures become comparable to the average grain size, some reliability issues can be reported for the moving parts of inertial microelectromechanical systems (MEMS). Not only the overall behavior of the device turns out to be affected by a large scattering, but also the sensitivity to imperfections gets enhanced. In this work, through on-chip tests, we experimentally investigate the behavior of thin polysilicon samples using standard electrostatic actuation/sensing. The discrepancy between the target and actual responses of each sample has then been exploited to identify: (i) the overall stiffness of the film and, according to standard continuum elasticity, a morphology-based value of its Young’s modulus; (ii) the relevant over-etch induced by the fabrication process. To properly account for the aforementioned stochastic features at the micro-scale, the identification procedure has been based on particle filtering. A simple analytical reduced-order model of the moving structure has been also developed to account for the nonlinearities in the electrical field, up to pull-in. Results are reported for a set of ten film samples of constant slenderness, and the effects of different actuation mechanisms on the identified micromechanical features are thoroughly discussed.
Open AccessMicromechanical Characterization of Polysilicon Films through On-Chip Tests
When the dimensions of polycrystalline structures become comparable to the average grain size, some reliability issues can be reported for the moving parts of inertial microelectromechanical systems (MEMS). Not only the overall behavior of the device turns out to be affected by a large scattering, but also the sensitivity to imperfections gets enhanced. In this work, through on-chip tests, we experimentally investigate the behavior of thin polysilicon samples using standard electrostatic actuation/sensing. The discrepancy between the target and actual responses of each sample has then been exploited to identify: (i) the overall stiffness of the film and, according to standard continuum elasticity, a morphology-based value of its Young’s modulus; (ii) the relevant over-etch induced by the fabrication process. To properly account for the aforementioned stochastic features at the micro-scale, the identification procedure has been based on particle filtering. A simple analytical reduced-order model of the moving structure has been also developed to account for the nonlinearities in the electrical field, up to pull-in. Results are reported for a set of ten film samples of constant slenderness, and the effects of different actuation mechanisms on the identified micromechanical features are thoroughly discussed.
- Open Access
- 2 June 2014
- Published by MDPI AG
Modeling of Fluid Damping in Resonant Micromirrors with Out-of-Plane Comb-Drive Actuation
Comb-drive micromirrors are becoming of interest for a broad range of light manipulation applications. For some of these applications a vacuum packaging, which is able to guarantee higher quality factors, turns out to be not favorable for technical and functional reasons. Furthermore, micromirrors for picoprojectors application are required to function at high frequencies in order to achieve high resolution images. Accordingly, a study of the energy dissipated due to the interaction between the moving parts of the micromirror and the surrounding air, leading to fluid damping, is an important issue. Even if air damping has been thoroughly studied, an extension to large air domain distortion linked to large tilting angles of torsional micromirrors, is still partially missing. In such situations, the flow formation turns out to be far more complex than that assumed in analytical models. This task is here pursued by adopting three-dimensional computational fluid dynamics models; specifically, two models, holding at different length scales, are adopted to attack the problem through an automated dynamic remeshing method. The time evolution of the torque required to compensate for the fluid damping term is computed for a specific micromirror geometry. The relative contributions due to drag, shear and squeeze film terms are calculated as well. These results are shown to compare well with the available experimental data in terms of the overall sensor quality factor.
- 2 June 2014
- Published by MDPI AG
Open AccessModeling of Fluid Damping in Resonant Micromirrors with Out-of-Plane Comb-Drive Actuation
Comb-drive micromirrors are becoming of interest for a broad range of light manipulation applications. For some of these applications a vacuum packaging, which is able to guarantee higher quality factors, turns out to be not favorable for technical and functional reasons. Furthermore, micromirrors for picoprojectors application are required to function at high frequencies in order to achieve high resolution images. Accordingly, a study of the energy dissipated due to the interaction between the moving parts of the micromirror and the surrounding air, leading to fluid damping, is an important issue. Even if air damping has been thoroughly studied, an extension to large air domain distortion linked to large tilting angles of torsional micromirrors, is still partially missing. In such situations, the flow formation turns out to be far more complex than that assumed in analytical models. This task is here pursued by adopting three-dimensional computational fluid dynamics models; specifically, two models, holding at different length scales, are adopted to attack the problem through an automated dynamic remeshing method. The time evolution of the torque required to compensate for the fluid damping term is computed for a specific micromirror geometry. The relative contributions due to drag, shear and squeeze film terms are calculated as well. These results are shown to compare well with the available experimental data in terms of the overall sensor quality factor.
- 1 April 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
Fluid damping in compliant, comb-actuated torsional micromirrors
Fluid damping is studied for resonant torsional micromirrors, electrostatically actuated by comb fingers. A three-dimensional computational fluid dynamics (CFD) model of the air flow around the moving parts of the mirror is developed, coping with dynamic remeshing procedures to properly account for the large displacement setting required by the motion of the compliant structure. The time evolution of the damping torque contributions, due to shear at comb fingers and to drag over the surfaces of the micromirror plate, are computed. The relevant numerical estimation of the overall quality factor of the system is shown to compare well with available experimental results.
- 1 April 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
Fluid damping in compliant, comb-actuated torsional micromirrors
Fluid damping is studied for resonant torsional micromirrors, electrostatically actuated by comb fingers. A three-dimensional computational fluid dynamics (CFD) model of the air flow around the moving parts of the mirror is developed, coping with dynamic remeshing procedures to properly account for the large displacement setting required by the motion of the compliant structure. The time evolution of the damping torque contributions, due to shear at comb fingers and to drag over the surfaces of the micromirror plate, are computed. The relevant numerical estimation of the overall quality factor of the system is shown to compare well with available experimental results.