Galina V. Odintsova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Galina V. Odintsova has a total of 158 co-authors. Here are the top co-authors by number of shared publications:
- Eduard I. Ageev
ITMO University
10 shared publications V. P. Veiko
ITMO University, Institute of Laser Technologies, St. Petersburg, Russia
6 shared publications- Elena V. Gorbunova
ITMO Univ. (Russian Federation)
5 shared publications Vadim Veiko
5 shared publications- Yulia Karlagina
ITMO University
5 shared publications - Nadezhda Shchedrina
Institut de Chimie Moléculaire et Des Matériaux d’Orsay (ICMMO), Université Paris-Saclay, 91405 Orsay, France
4 shared publications
Latest Publications
- Open Access
- 21 May 2026
- Published by Elsevier in SSRN Electronic Journal
One step laser method for protecting steel surfaces from biofouling in marine water
This paper explores the possibility of reducing the level of biofouling on the surface of stainless steel AISI 430 using laser-generated surface structures. The choice of geometric parameters of laser-generated structures is based on the analysis of the mechanisms of attachment of microorganisms to a metal surface. The stainless steel is treated in air in normal conditions using a nanosecond laser with a wavelength of 1064 nm. Hydrophobization of the metal surface after laser structuring is realized by prolonged exposure of the samples to air. The degree of biofouling is measured using the chemical compounds resazurin and resorufin. The results demonstrate the effectiveness of hydrophobic periodic reliefs with elements of microstructure smaller than adult microorganisms. These structures have 30-50 % less biota values as compared to the untreated material. The locality, eco-friendliness and no additional materials in this method are major advantages for industrial applications.
- 21 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessOne step laser method for protecting steel surfaces from biofouling in marine water
This paper explores the possibility of reducing the level of biofouling on the surface of stainless steel AISI 430 using laser-generated surface structures. The choice of geometric parameters of laser-generated structures is based on the analysis of the mechanisms of attachment of microorganisms to a metal surface. The stainless steel is treated in air in normal conditions using a nanosecond laser with a wavelength of 1064 nm. Hydrophobization of the metal surface after laser structuring is realized by prolonged exposure of the samples to air. The degree of biofouling is measured using the chemical compounds resazurin and resorufin. The results demonstrate the effectiveness of hydrophobic periodic reliefs with elements of microstructure smaller than adult microorganisms. These structures have 30-50 % less biota values as compared to the untreated material. The locality, eco-friendliness and no additional materials in this method are major advantages for industrial applications.
- Open Access
- 13 April 2026
- Published by Elsevier in SSRN Electronic Journal
Surface Quality Improvement of Selective Laser Melted Ti-6Al-4V and Hastelloy X via Laser Processing
Selective Laser Melting (SLM) is an advanced additive manufacturing technique widely used in structural, bio-medical, and high-performance engineering applications due to its ability to fabricate complex geometries; however, SLM-fabricated parts often exhibit high surface roughness and surface-connected defects such as partially fused particles, pores, and microcracks. This study presents an experimental investigation into laser surface treatment as a post-processing method to enhance the surface quality of Ti-6Al-4V and Hastelloy X components produced by SLM, with the primary objectives of reducing surface roughness, sealing pores and cracks, and improving surface integrity. The effects of key laser processing parameters—including laser beam defocus, track overlap, hatch pattern, and number of scan passes—on surface roughness, micro-scale surface morphology, and near-surface chemical composition are systematically examined. Surface treatment is performed in ambient air using a pulsed laser irradiation, and the treated surfaces are characterized using surface profilometry, optical microscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The results show that suitable combinations of laser defocus and track overlap significantly reduce surface roughness and promote effective remelting of partially fused particles, while multiple scan passes enhance pore sealing and crack healing; however, excessive energy input may lead to localized surface oxidation.
- 13 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSurface Quality Improvement of Selective Laser Melted Ti-6Al-4V and Hastelloy X via Laser Processing
Selective Laser Melting (SLM) is an advanced additive manufacturing technique widely used in structural, bio-medical, and high-performance engineering applications due to its ability to fabricate complex geometries; however, SLM-fabricated parts often exhibit high surface roughness and surface-connected defects such as partially fused particles, pores, and microcracks. This study presents an experimental investigation into laser surface treatment as a post-processing method to enhance the surface quality of Ti-6Al-4V and Hastelloy X components produced by SLM, with the primary objectives of reducing surface roughness, sealing pores and cracks, and improving surface integrity. The effects of key laser processing parameters—including laser beam defocus, track overlap, hatch pattern, and number of scan passes—on surface roughness, micro-scale surface morphology, and near-surface chemical composition are systematically examined. Surface treatment is performed in ambient air using a pulsed laser irradiation, and the treated surfaces are characterized using surface profilometry, optical microscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The results show that suitable combinations of laser defocus and track overlap significantly reduce surface roughness and promote effective remelting of partially fused particles, while multiple scan passes enhance pore sealing and crack healing; however, excessive energy input may lead to localized surface oxidation.
- 29 June 2023
- Published by Springer Nature in Optical and Quantum Electronics
- Vol. 55 (9) , 1-16
Laser-induced antibacterial coating on the surface of an individual titanium membrane designed by a neural network
- 29 June 2023
- Published by Springer Nature in Optical and Quantum Electronics
- Vol. 55 (9) , 1-16
Laser-induced antibacterial coating on the surface of an individual titanium membrane designed by a neural network
- 1 April 2023
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 90 (4) , 170-178
Laser-based formation of periodic structures as a method for the one-stage production of security holograms
Subject of study. In this study, methods for the topology formation of elements based on laser-induced periodic surface structures for implementing various visual effects and structural features in a security hologram recorded directly on the surface of AISI 430 stainless steel are investigated. Purpose of work. The process of recording images based on laser-induced periodic surface structures on bulk metals for creating dynamic images is optimized to solve problems in security holography. Method. The method is based on the formation of laser-induced periodic surface structures under the action of scanning laser radiation with simultaneous rotation of the polarization of laser radiation. The recording process is implemented using nanosecond fiber laser radiation with a wavelength of 1.064 µm in a two-dimensional scanning system with a flat field objective. Main results. A technique is developed for creating a protective hologram comprising a set of laser prints filled with diffractive microgratings with different spatial orientations. The radiation polarization and beam scanning trajectory are the main factors influencing the laser-induced periodic surface structures’ spatial orientation during the formation of structures with a given topology and observed visual dynamic effects based on elementary diffractive microgratings. The period of microdiffraction gratings is equal to the wavelength of the acting laser radiation and approximately 1 µm. Practical significance. The proposed method for the elementary diffractive micrograting formation facilitates the generation of holographic elements/images with different spatial topologies, including various visual and structural features that meet the requirements for modern security holograms in their main application areas.
- 1 April 2023
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 90 (4) , 170-178
Laser-based formation of periodic structures as a method for the one-stage production of security holograms
Subject of study. In this study, methods for the topology formation of elements based on laser-induced periodic surface structures for implementing various visual effects and structural features in a security hologram recorded directly on the surface of AISI 430 stainless steel are investigated. Purpose of work. The process of recording images based on laser-induced periodic surface structures on bulk metals for creating dynamic images is optimized to solve problems in security holography. Method. The method is based on the formation of laser-induced periodic surface structures under the action of scanning laser radiation with simultaneous rotation of the polarization of laser radiation. The recording process is implemented using nanosecond fiber laser radiation with a wavelength of 1.064 µm in a two-dimensional scanning system with a flat field objective. Main results. A technique is developed for creating a protective hologram comprising a set of laser prints filled with diffractive microgratings with different spatial orientations. The radiation polarization and beam scanning trajectory are the main factors influencing the laser-induced periodic surface structures’ spatial orientation during the formation of structures with a given topology and observed visual dynamic effects based on elementary diffractive microgratings. The period of microdiffraction gratings is equal to the wavelength of the acting laser radiation and approximately 1 µm. Practical significance. The proposed method for the elementary diffractive micrograting formation facilitates the generation of holographic elements/images with different spatial topologies, including various visual and structural features that meet the requirements for modern security holograms in their main application areas.
- 13 February 2023
- Published by Springer Nature in Optical and Quantum Electronics
- Vol. 55 (4) , 1-12
Enhancing the pitting resistance of AISI 430 stainless steel by laser treatment
- 13 February 2023
- Published by Springer Nature in Optical and Quantum Electronics
- Vol. 55 (4) , 1-12
Enhancing the pitting resistance of AISI 430 stainless steel by laser treatment
- 21 December 2022
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 39 (1) , 204-210
Eco-friendly Approach for Creation of Resonant Silicon Nanoparticle Colloids
The commercial application of Mie-resonant nanophotonic technologies currently used in various laboratory studies, from biosensing to quantum optics, appears to be challenging. Development of colloidal-based fabrication approaches is a solution to face the issue. In our research, we studied the fabrication of resonant Si nanoparticle (NP) arrays on a surface with controlled wettability. First, we use nanosecond (ns) laser ablation in water and subsequent density gradient separation to obtain colloids of resonant spherical crystalline silicon NPs with a low polydispersity index. Then, the same industrial ns laser is applied to create a wetting gradient on the steel substrate to initiate a self-assembly of the NPs deposited by drop casting. Thus, we use a single commercial ns laser for producing both the NPs and the hydrophilic wetting gradient. We apply an easily operating size separation technique and only nontoxic media. This research contributes to the large-scale fabrication of various optical devices based on resonant high-refractive index nanostructures by ecologically friendly self-assembly techniques.
- 21 December 2022
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 39 (1) , 204-210
Eco-friendly Approach for Creation of Resonant Silicon Nanoparticle Colloids
The commercial application of Mie-resonant nanophotonic technologies currently used in various laboratory studies, from biosensing to quantum optics, appears to be challenging. Development of colloidal-based fabrication approaches is a solution to face the issue. In our research, we studied the fabrication of resonant Si nanoparticle (NP) arrays on a surface with controlled wettability. First, we use nanosecond (ns) laser ablation in water and subsequent density gradient separation to obtain colloids of resonant spherical crystalline silicon NPs with a low polydispersity index. Then, the same industrial ns laser is applied to create a wetting gradient on the steel substrate to initiate a self-assembly of the NPs deposited by drop casting. Thus, we use a single commercial ns laser for producing both the NPs and the hydrophilic wetting gradient. We apply an easily operating size separation technique and only nontoxic media. This research contributes to the large-scale fabrication of various optical devices based on resonant high-refractive index nanostructures by ecologically friendly self-assembly techniques.
- Open Access
- 28 November 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (23) , 4229
Laser-Induced µ-Rooms for Osteocytes on Implant Surface: An In Vivo Study
Laser processing of dental implant surfaces is becoming a more widespread replacement for classical techniques due to its undeniable advantages, including control of oxide formation and structure and surface relief at the microscale. Thus, using a laser, we created several biomimetic topographies of various shapes on the surface of titanium screw-shaped implants to research their success and survival rates. A distinctive feature of the topographies is the presence of “µ-rooms”, which are special spaces created by the depressions and elevations and are analogous to the µ-sized room in which the osteocyte will potentially live. We conducted the comparable in vivo study using dental implants with continuous (G-topography with µ-canals), discrete (S-topography with μ-cavities), and irregular (I-topography) laser-induced topographies. A histological analysis performed with the statistical method (with p-value less than 0.05) was conducted, which showed that G-topography had the highest BIC parameter and contained the highest number of mature osteocytes, indicating the best secondary stability and osseointegration.
- 28 November 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (23) , 4229
Open AccessLaser-Induced µ-Rooms for Osteocytes on Implant Surface: An In Vivo Study
Laser processing of dental implant surfaces is becoming a more widespread replacement for classical techniques due to its undeniable advantages, including control of oxide formation and structure and surface relief at the microscale. Thus, using a laser, we created several biomimetic topographies of various shapes on the surface of titanium screw-shaped implants to research their success and survival rates. A distinctive feature of the topographies is the presence of “µ-rooms”, which are special spaces created by the depressions and elevations and are analogous to the µ-sized room in which the osteocyte will potentially live. We conducted the comparable in vivo study using dental implants with continuous (G-topography with µ-canals), discrete (S-topography with μ-cavities), and irregular (I-topography) laser-induced topographies. A histological analysis performed with the statistical method (with p-value less than 0.05) was conducted, which showed that G-topography had the highest BIC parameter and contained the highest number of mature osteocytes, indicating the best secondary stability and osseointegration.
- 30 May 2022
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 13 (3) , 879-886
Laser Formation and Influence of Laser Radiation on Basic Characteristics of Barcodes
An analysis of the advantages of laser marking is carried out in comparison with other methods of forming a given surface relief of structural materials, forming barcodes, and reading them. The necessary conditions for stable reading of barcodes, described by the value of the contrast ratio, are formulated. The elements of the prints of the laser exposure pattern that make up the barcode are classified, and an example of measuring and calculating the contrast ratio of samples using spectrophotometry is given. The parameters of the surface relief in the areas of the applied barcode are measured using scanning probe microscopy. The analysis of the influence of the parameters of laser radiation on the geometric characteristics of the elements of the barcode and the value of its contrast ratio is carried out.
- 30 May 2022
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 13 (3) , 879-886
Laser Formation and Influence of Laser Radiation on Basic Characteristics of Barcodes
An analysis of the advantages of laser marking is carried out in comparison with other methods of forming a given surface relief of structural materials, forming barcodes, and reading them. The necessary conditions for stable reading of barcodes, described by the value of the contrast ratio, are formulated. The elements of the prints of the laser exposure pattern that make up the barcode are classified, and an example of measuring and calculating the contrast ratio of samples using spectrophotometry is given. The parameters of the surface relief in the areas of the applied barcode are measured using scanning probe microscopy. The analysis of the influence of the parameters of laser radiation on the geometric characteristics of the elements of the barcode and the value of its contrast ratio is carried out.
- 1 January 2022
- Published by Ioffe Institute Russian Academy of Sciences in Technical Physics Letters
- Vol. 48 (1) , 56
Investigation of the effect of nanosecond laser pulses processing on the microstructure and fatigue resistance of commercially pure titanium
The effect has been studied of treatment with nanosecond laser pulses on the fatigue resistance of plate samples of recrystallized (grain size of the order of 2-3 μm) commercially pure titanium (grade VT1-0) under cyclic tensile loading. The results of investigations by scanning and transmission electron microscopy of the subsurface layer microstructure of the alloy under study after exposure to nanosecond laser irradiation and subsequent fatigue tests are presented. Keywords: titanium, surface, pulsed nanosecond laser irradiation, shock-wave action, fatigue properties.
- 1 January 2022
- Published by Ioffe Institute Russian Academy of Sciences in Technical Physics Letters
- Vol. 48 (1) , 56
Investigation of the effect of nanosecond laser pulses processing on the microstructure and fatigue resistance of commercially pure titanium
The effect has been studied of treatment with nanosecond laser pulses on the fatigue resistance of plate samples of recrystallized (grain size of the order of 2-3 μm) commercially pure titanium (grade VT1-0) under cyclic tensile loading. The results of investigations by scanning and transmission electron microscopy of the subsurface layer microstructure of the alloy under study after exposure to nanosecond laser irradiation and subsequent fatigue tests are presented. Keywords: titanium, surface, pulsed nanosecond laser irradiation, shock-wave action, fatigue properties.
- 1 October 2021
- Published by Springer Nature in Russian Physics Journal
- Vol. 64 (6) , 1055-1059
A Study of the Influence of Irradiation of Carbon Diamond-Like Coatings with Nanosecond Laser Pulses on Their Structural-Phase Composition and Tribological Properties
- 1 October 2021
- Published by Springer Nature in Russian Physics Journal
- Vol. 64 (6) , 1055-1059
A Study of the Influence of Irradiation of Carbon Diamond-Like Coatings with Nanosecond Laser Pulses on Their Structural-Phase Composition and Tribological Properties