Mohammed Ahmed Al-Bukhaiti
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mohammed Ahmed Al-Bukhaiti has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Ahmed Abouel Kasem Mohamad
King Abdulaziz University Department of Mechanical Engineering, Faculty of Eng.-Rabigh P. O. Box 344, Rabigh 21911 , Saudi Arabia
3 shared publications - Karam Mosa Emara
Mechanical Engineering Department, Faculty of Engineering, Assiut University, Assiut 71516, Egypt
3 shared publications - Shemy M. Ahmed
Mechanical Engineering Department, Faculty of Engineering, Majmaah University, North Riyadh, Kingdom of Saudi Arabia
3 shared publications
Latest Publications
- 8 May 2018
- Published by Emerald Publishing in Industrial Lubrication and Tribology
- Vol. 70 (4) , 628-638
Effect of slurry concentration on erosion wear behavior of AISI 5117 steel and high-chromium white cast iron
Purpose: This paper aims to investigate the influence of slurry concentration on the erosion behavior of AISI 5117 steel and high-chromium white cast iron by using a whirling-arm rig. In this study, the slurry erosion mechanism with particle concentration has been studied. Design/methodology/approach: The tests were carried out with particle concentrations in the range of 1-7 Wt.%, and the impact velocity of slurry stream was 15 m/s. Silica sand with a nominal size range of 500-710 µm was used as an erodent. The study revealed that the failure mode was independent of concentration. Findings: The results showed that the erosion rate decreases with the increase in particle concentration and the variation in the reduction depends on the material. It was found that the variation of fractal dimension calculated from slope of linearized power spectral density of eroded surface image for different concentrations can be used to characterize the slurry erosion intensity in a similar manner to the erosion rate. It was also found that the variation of fractal dimension versus concentration of sand has a general trend that does not depend on magnification factor. Originality/value: Using the gravitational measurement and image analysis, the variation of the wear with slurry concentration has been analyzed to investigate the implicated mechanisms of erosion during the process.
- 8 May 2018
- Published by Emerald Publishing in Industrial Lubrication and Tribology
- Vol. 70 (4) , 628-638
Effect of slurry concentration on erosion wear behavior of AISI 5117 steel and high-chromium white cast iron
Purpose: This paper aims to investigate the influence of slurry concentration on the erosion behavior of AISI 5117 steel and high-chromium white cast iron by using a whirling-arm rig. In this study, the slurry erosion mechanism with particle concentration has been studied. Design/methodology/approach: The tests were carried out with particle concentrations in the range of 1-7 Wt.%, and the impact velocity of slurry stream was 15 m/s. Silica sand with a nominal size range of 500-710 µm was used as an erodent. The study revealed that the failure mode was independent of concentration. Findings: The results showed that the erosion rate decreases with the increase in particle concentration and the variation in the reduction depends on the material. It was found that the variation of fractal dimension calculated from slope of linearized power spectral density of eroded surface image for different concentrations can be used to characterize the slurry erosion intensity in a similar manner to the erosion rate. It was also found that the variation of fractal dimension versus concentration of sand has a general trend that does not depend on magnification factor. Originality/value: Using the gravitational measurement and image analysis, the variation of the wear with slurry concentration has been analyzed to investigate the implicated mechanisms of erosion during the process.
- 29 March 2017
- Published by ASME International in Journal of Tribology
- Vol. 139 (4) , 041102
A Study on Slurry Erosion Behavior of High Chromium White Cast Iron
High chromium white irons (HCCIs) are used extensively throughout the mineral processing industry to handle erosive and corrosive slurries. This study is an investigation of the effect of impact angle and velocity on slurry erosion of HCCI. The tests were carried out using a rotating whirling-arm rig with particle concentration of 1 wt. %. Silica sand which has a nominal size range of 500–710 μm was used as an erodent. The results were obtained for angles of 30 deg, 45 deg, 60 deg, and 90 deg to the exposed surface and velocities of 5, 10, and 15 m/s. The highest erosion resistance of HCCI was at normal impact and the lowest at an angle of 30 deg, irrespective of velocity. The low erosion resistance at an oblique angle is due to large material removal by microcutting from ductile matrix and gross removal of carbides. The effect of velocity, over the studied range from 5 m/s to 15 m/s, on the increase in the erosion rate was minor. The change of impact velocity resulted in changing the slurry erosion mechanisms. At normal incidence, plastic indentation with extruded material of the ductile matrix was the dominant erosion mechanism at low impact velocity (5 m/s). With increasing impact velocity, the material was removed by the indentation of the ductile matrix and to smaller extent of carbide fracture. However, at high impact velocity (15 m/s), gross fracture and cracking of the carbides besides plastic indentation of the ductile matrix were the dominant erosion mechanisms.
- 29 March 2017
- Published by ASME International in Journal of Tribology
- Vol. 139 (4) , 041102
A Study on Slurry Erosion Behavior of High Chromium White Cast Iron
High chromium white irons (HCCIs) are used extensively throughout the mineral processing industry to handle erosive and corrosive slurries. This study is an investigation of the effect of impact angle and velocity on slurry erosion of HCCI. The tests were carried out using a rotating whirling-arm rig with particle concentration of 1 wt. %. Silica sand which has a nominal size range of 500–710 μm was used as an erodent. The results were obtained for angles of 30 deg, 45 deg, 60 deg, and 90 deg to the exposed surface and velocities of 5, 10, and 15 m/s. The highest erosion resistance of HCCI was at normal impact and the lowest at an angle of 30 deg, irrespective of velocity. The low erosion resistance at an oblique angle is due to large material removal by microcutting from ductile matrix and gross removal of carbides. The effect of velocity, over the studied range from 5 m/s to 15 m/s, on the increase in the erosion rate was minor. The change of impact velocity resulted in changing the slurry erosion mechanisms. At normal incidence, plastic indentation with extruded material of the ductile matrix was the dominant erosion mechanism at low impact velocity (5 m/s). With increasing impact velocity, the material was removed by the indentation of the ductile matrix and to smaller extent of carbide fracture. However, at high impact velocity (15 m/s), gross fracture and cracking of the carbides besides plastic indentation of the ductile matrix were the dominant erosion mechanisms.
- 29 January 2016
- Published by ASME International in Journal of Tribology
- Vol. 138 (2) , 024503
Particle Shape and Size Effects on Slurry Erosion of AISI 5117 Steels
Solid particle shape and size effects on the slurry erosion behavior of AISI 5117 carbon steels are investigated, using whirling-arm ring for two different erodent particles, namely, silica sand (SiO2) and silicon carbide (SiC). From this work, it was found that aspect ratio and circularity factor (CF) increase for silica sand and decrease for silicon carbide with increasing size. The erosion rate increased with the increase of particle size for the two types of erodent particles and its value was greater in the case of silicon carbide particles. At the same test conditions, it has been noticed that the particle size plays the major role in the slurry erosion of 5117 steels in comparison with the aspect ratio and circularity factor. Microcutting and plowing with serrated wear tracks were observed for coarse SiC particles having irregular and angular shape. But, for coarse SiO2 particles which had a rounded shape, the main mechanism was plowing with plain and smooth wear tracks for an impact angle of 30 deg. Indentations and material extrusion prevailed for the coarse size of the two erodents for an impact angle of 90 deg.
- 29 January 2016
- Published by ASME International in Journal of Tribology
- Vol. 138 (2) , 024503
Particle Shape and Size Effects on Slurry Erosion of AISI 5117 Steels
Solid particle shape and size effects on the slurry erosion behavior of AISI 5117 carbon steels are investigated, using whirling-arm ring for two different erodent particles, namely, silica sand (SiO2) and silicon carbide (SiC). From this work, it was found that aspect ratio and circularity factor (CF) increase for silica sand and decrease for silicon carbide with increasing size. The erosion rate increased with the increase of particle size for the two types of erodent particles and its value was greater in the case of silicon carbide particles. At the same test conditions, it has been noticed that the particle size plays the major role in the slurry erosion of 5117 steels in comparison with the aspect ratio and circularity factor. Microcutting and plowing with serrated wear tracks were observed for coarse SiC particles having irregular and angular shape. But, for coarse SiO2 particles which had a rounded shape, the main mechanism was plowing with plain and smooth wear tracks for an impact angle of 30 deg. Indentations and material extrusion prevailed for the coarse size of the two erodents for an impact angle of 90 deg.