PTPaulo Toro

Paulo Toro

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Paulo Toro has a total of 31 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Experimental Validation of a Hybrid Additively Manufactured Contour Nozzle for Hypersonic Shock Tunnels

    by Renan G. S. Vilela, Lucas Ribeiro, Rafael O. Santos, Pedro Antonio de Souza Matos, Giannino P. Camillo, André C. Fraile Jr., Marco Minucci, Israel S. Rego, Paulo Gilberto de Paula Toro

    This work presents the development, manufacturing, and validation of a hybrid additively manufactured contour nozzle for the T2 hypersonic shock tunnel at the Brazilian Institute for Advanced Studies. Although the influence of nozzle geometry on hypersonic flow quality is well established, the potential impact of additive manufacturing and hybrid construction on the generated flow remains uncertain. Therefore, the experimental campaign was structured to isolate manufacturing-related effects before evaluating the contour nozzle configuration. The study was conducted in two stages. First, a conventional metallic conical nozzle was compared with a geometrically equivalent hybrid conical nozzle, allowing the influence of manufacturing process and material to be assessed independently of geometry. Subsequently, a hybrid contour nozzle was experimentally evaluated under equivalent manufacturing conditions. Flow quality was characterized through stagnation pressure measurements obtained using a Pitot pressure rake positioned at the nozzle exit plane and 100 mm downstream. The metallic and hybrid conical nozzles produced similar flow distributions, indicating that the additive manufacturing process and the increased surface roughness did not significantly affect the overall flow structure. In contrast, the contour nozzle generated a larger and more uniform supersonic core, increasing the region with total pressure above 90% of the centerline value from less than 20% to approximately 75% of the nozzle diameter. Qualitative agreement was observed between the experimental and numerical results. The results demonstrate that hybrid additively manufactured contour nozzles are a viable alternative for hypersonic shock tunnel applications, providing improved flow quality while reducing manufacturing complexity, lead time, and cost.

  • Open Access

    An overview of real gas effects in the high-temperature air after the normal shock wave

    by Eduardo Katsuo Silva Paixão, Patricia Grezelle, Heidi Korzenowski, Francisco Augusto Aparecido Gomes, George Santos Marinho, Paulo Gilberto de Paula Toro

    Under subsonic and low supersonic flight conditions, airflow properties are well known, and the calorically perfect gas relation may be used. In general, under high supersonic flight conditions, air should be treated as a thermally perfect gas, where the ratio of specific heats at constant pressure and at constant volume is a function of the temperature. For hypersonic flight conditions, air can no longer be treated as a calorically or thermally perfect gas, and any thermodynamic property is a function of two other thermodynamic properties, known as equilibrium air (real gas effects). The thermodynamic equilibrium properties of the air have been numerically investigated since as early as 1950, and simplified curve fits for the thermodynamic properties of equilibrium air have been devised for use in either the time-dependent or shock-capturing computational methods \textit{engineering methods}. This paper presents a numerical methodology to estimate the conditions right after the normal shock wave, considering both cases, air as a calorically perfect gas, and in chemical and thermodynamic equilibrium. Thermodynamic properties (pressure, temperature, and density) ratios right after the normal shock wave can be obtained based on theoretical analysis using one-dimensional normal shock wave compressible flow. Conditions behind the normal shock waves considering two gas models, calorically perfect, and chemical and thermodynamic equilibrium are presented, functions of the Earth's atmospheric air, and flight conditions. The numerical methodology developed in this work was compared/validated with results from classic works of the literature, showing precision and physical robustness regarding the effect of real gas on thermodynamic properties after the normal shock wave, in addition to excellent agreement with the results in the literature.

  • Open Access

    Multi-objective optimization of a hypersonic airbreathing vehicle

    by Pedro P. B. Araújo, Roberto Y. Tanaka, Carlos A. Silva, Angelo Passaro, Paulo G. P. Toro

    Multi-objective optimization of a hypersonic airbreathing engine (scramjet technology) was carried out with the aim of maximizing thrust and minimizing drag while satisfying a series of design constraints, such as avoiding unstart (blockage of supersonic flow within the combustion chamber) by ensuring that the pressure ratio across the shock waves remains below the adverse pressure gradient given by the Korkegi limit, geometry correction to achieve shock on-lip condition, and temperature and pressure requirements at the inlet exit. Using the relations presented in the literature, pressure and viscous drag are estimated analytically. The analytical approach is verified against computational fluid dynamics data from Ansys Fluent to solve two-dimensional compressible Reynolds-averaged Navier–Stokes flow equations, with transition shear stress transport as the turbulence closure model. Comparing the total drag and the flow properties at the combustion chamber entrance shows the model's feasibility for the optimization approach. Three different approaches were conducted to formulate the multi-objective function to determine the one that can find the highest number of geometries satisfying the Korkegi limit with the highest net thrust. The best approach was the multi-objective function formulated with the uninstalled thrust, total pressure recovery, and pressure drag, concentrating the search in the region with greater uninstalled thrust and lower drag and nearly doubling the value of net thrust compared to the first formulation, which uses the uninstalled thrust, pressure drag, and viscous drag.


  • Heat addition with variable area: Methodology for preliminary design of the scramjet combustion chamber

    by R. Carneiro, A. Passaro, P. G. P. Toro

    Well-known analytical approaches are commonly adopted for the preliminary design of scramjet engines. In this context, the combustion process in the combustion chamber can be modeled by considering heat addition to the airflow at supersonic speed. The one-dimensional Rayleigh flow theory can be applied to estimate the behavior of thermodynamic properties and velocities when the combustion chamber has a constant cross-sectional area and no mass is added within the duct. However, the temperature and pressure predicted by using constant area combustion chambers are too high, implying the necessity of modifications in the cross-sectional area of the chamber to avoid thermal choking and excessive pressure gradients. In this case, the unidimensional Rayleigh theory does not fit anymore. This work proposes an analytical methodology to estimate the airflow thermodynamic properties and velocities for scramjet combustion chambers with cross sections of variable areas by using an iterative algorithm that employs the Rayleigh flow area ratio theory. The analytical results were compared with the two-dimensional computational fluid dynamics analysis using the Reynolds-averaged Navier–Stokes method for both inviscid and viscous flow and considering turbulence effects. The proposed analytical model to estimate the flow behavior in the scramjet combustion chamber predicted results in agreement with the physics of the problem and with the results obtained via numerical simulation. The analytical model cannot predict oscillations in the flow properties caused by the expansion waves and their reflections. Still, the behavior and intensity of the properties are well captured along the entire length of three combustion chambers with variable area. The proposed algorithm is also applied to determine the angle of the combustion chamber that allows guaranteeing a constant, or a quasi-constant, static pressure along the length of the combustion chamber, approaching better the ideal thermodynamic Brayton cycle. The proposed model is suitable for preliminary scramjet designs and can be used to solve other problems involving variable area ducts.


  • Open Access

    Leading-to-trailing edge theoretical design of a generic scramjet

    by R. Carneiro, P. P. B. Araújo, G. S. Marinho, J. F. A. Martos, A. Passaro, P. G. P. Toro

    The aerospace vehicle flying at hypersonic speed, using an airbreathing propulsion system based on supersonic combustion (scramjet) technology, requires a highly integrated system without moving parts, making the propulsion system and vehicle shape indistinguishable. A scramjet uses shock waves, generated by its inlet during the hypersonic flight to provide the temperature and velocity of atmospheric air to burn the hydrogen, at the combustor at supersonic speed. The divergent exhaust nozzle accelerates the combustion products providing the thrust. A two-dimensional hydrogen-powered generic scramjet has been designed to demonstrate supersonic combustion in atmospheric flight at a Mach number of 6.8 and an altitude of 30 km. Temperature and velocity at the combustion chamber are the most important key parameters for a preliminary design. The inlet configuration must provide a temperature higher than the ignition temperature of the fuel to guarantee spontaneous combustion and the velocity must remain supersonics. The nozzle exit velocity should be higher than the vehicle flight velocity to obtain sustained flight and produce enough thrust. For this theoretical analysis, the air is considered a calorically perfect gas without viscous effects. The compressible flow is analyzed based on oblique shock waves and one-dimensional compressible flow with friction and heat addition and Prandtl–Meyer coupled to the area ratio to describe each key component of the scramjet, such as compression, combustor, and nozzle sections, respectively. The inlet mass flow and hydrogen mass flow are also critical for the scramjet design to ensure stoichiometrically combustion at the combustion chamber, generating the high flow velocity at the nozzle to produce thrust.


  • Optimization of scramjet inlet based on temperature and Mach number of supersonic combustion

    by Pedro P.B. Araújo, Marcos V.S. Pereira, George S. Marinho, João F.A. Martos, Paulo G.P. Toro


  • DEVELOPMENT AND COMPARISON OF PLANAR AND CONICAL SCRAMJET VEHICLE INLET

    by Luiz Henrique Silva Marques Soares, Heidi Korzenowski, Paulo Toro, João Felipe De Araujo Martos

  • A BRIEF REVIEW OF WALL SHEAR CORRELATIONS FOR HYPERSONIC FLOWS

    by Pedro Paulo Batista de Araújo, Felipe Pinheiro Maia, Jonatha Wallace da Silva Araújo, Ramon Carneiro, Ítalo Sabino Arrais Bezerra, Paulo Toro, Sandi Souza, Thiago Cardoso de Souza

  • THERMODYNAMIC ANALYSIS OF THE HYPERSONIC FLOW OVER A SCRAMJET DEMONSTRATOR CONSIDERING DIFFERENT GAS MODELS

    by Ramon Carneiro, Angelo Passaro, Felipe Pinheiro Maia, Jonatha Wallace da Silva Araújo, Ítalo Sabino Arrais Bezerra, Pedro Paulo Batista de Araújo, Paulo Toro

  • AEROTERMODYNAMIC HEATING IN THE COMPRESSION SECTION OF A SCRAMJET DEMONSTRATOR UNDER BALLISTIC TRAJECTORY

    by Ítalo Sabino Arrais Bezerra, Jonatha Wallace da Silva Araújo, Felipe Pinheiro Maia, Ramon Carneiro, Pedro Paulo Batista de Araújo, Paulo Toro