Scott A. Mauger
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Scott A. Mauger has a total of 149 co-authors. Here are the top co-authors by number of shared publications:
Michael Ulsh
National Laboratory of the Rockies, Golden, Colorado, USA
18 shared publications- Svitlana Pylypenko
Colorado School of Mines
11 shared publications - Kenneth C. Neyerlin
National Renewable Energy Laboratory
8 shared publications - Sunilkumar Khandavalli
National Renewable Energy Lab
7 shared publications - Guido Bender
National Laboratory of the Rockies, Golden, CO (United States)
6 shared publications Deborah J. Myers
5 shared publications
Latest Publications
- Open Access
- 1 September 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 272
Low volatile organic compound (VOC) fuel cell inks: Effects of water content on ink microstructure and catalyst layer cracking
- 1 September 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 272
Open AccessLow volatile organic compound (VOC) fuel cell inks: Effects of water content on ink microstructure and catalyst layer cracking
- Open Access
- 16 February 2026
- Published by Royal Society of Chemistry (RSC) in Energy Advances
- Vol. 5 (4) , 394-407
Uniformity, performance, and durability of roll-to-roll-coated iridium oxide electrolyzer catalyst layers
This work investigates the use of roll-to-roll coating methods for the production of iridium oxide catalyst layers for proton exchange membrane water electrolyzers. Catalyst layers were produced using two coating methods: slot die and gravure. By varying the solids content of the catalyst ink and coating process variables loadings between 0.08 and 0.64 mgIr cm−2 were prepared with relatively high spatial uniformity. However, at loadings below 0.2 mgIr cm−2 microscopy reveals voids in the catalyst layer due to similar length scales of catalyst agglomerates and overall layer thickness. Electrochemical testing shows that these voids do not impact initial membrane electrode assembly performance but lead to increased performance losses after potential cycling compared to spray coated catalyst layers.
- 16 February 2026
- Published by Royal Society of Chemistry (RSC) in Energy Advances
- Vol. 5 (4) , 394-407
Open AccessUniformity, performance, and durability of roll-to-roll-coated iridium oxide electrolyzer catalyst layers
This work investigates the use of roll-to-roll coating methods for the production of iridium oxide catalyst layers for proton exchange membrane water electrolyzers. Catalyst layers were produced using two coating methods: slot die and gravure. By varying the solids content of the catalyst ink and coating process variables loadings between 0.08 and 0.64 mgIr cm−2 were prepared with relatively high spatial uniformity. However, at loadings below 0.2 mgIr cm−2 microscopy reveals voids in the catalyst layer due to similar length scales of catalyst agglomerates and overall layer thickness. Electrochemical testing shows that these voids do not impact initial membrane electrode assembly performance but lead to increased performance losses after potential cycling compared to spray coated catalyst layers.
- 12 December 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 98, 639-647
The impact of hot-press conditions on the durability of polymer electrolyte membrane fuel cells
- 12 December 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 98, 639-647
The impact of hot-press conditions on the durability of polymer electrolyte membrane fuel cells
- 23 November 2024
- Published by Elsevier in Journal of Power Sources
- Vol. 628
The influence of electrode crack dimensions on the durability of polymer electrolyte membrane fuel cells
- 23 November 2024
- Published by Elsevier in Journal of Power Sources
- Vol. 628
The influence of electrode crack dimensions on the durability of polymer electrolyte membrane fuel cells
- 1 November 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 93, 116-121
Shelf-life of ball-milled catalyst inks for the fabrication of fuel cell electrodes
- 1 November 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 93, 116-121
Shelf-life of ball-milled catalyst inks for the fabrication of fuel cell electrodes
- Open Access
- 10 May 2024
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 128 (20) , 8467-8482
X-ray Photoelectron Spectroscopy Analysis of Nafion-Containing Samples: Pitfalls, Protocols, and Perceptions of Physicochemical Properties
X-ray photoelectron spectroscopy (XPS) is one of the most common techniques used to analyze the surface composition of catalysts and support materials used in polymer electrolyte membrane (PEM) fuel cells and electrolyzers, providing important insights for further improvement of their properties. Characterization of catalyst layers (CLs) is more challenging, which can be at least partially attributed to the instability of ionomer materials such as Nafion during measurements. This work explores the stability of Nafion during XPS measurements, illuminating and addressing Nafion degradation concerns. The extent of Nafion damage as a function of XPS instrumentation, measurement conditions, and sample properties was evaluated across multiple instruments. Results revealed that significant Nafion damage to the ion-conducting sulfonic acid species (>50% loss in sulfur signal) may occur in a relatively short time frame (tens of minutes) depending on the exact nature of the sample and XPS instrument. This motivated the development and validation of a multipoint XPS data acquisition protocol that minimizes Nafion damage, resulting in reliable data acquisition by avoiding significant artifacts from Nafion instability. The developed protocol was then used to analyze both thin film ionomer samples and Pt/C-based CLs. Comparison of PEM fuel cell CLs to Nafion thin films revealed several changes in Nafion spectral features attributed to charge transfer due to interaction with conductive catalyst and support species. This study provides a method to reliably characterize ionomer-containing samples, facilitating fundamental studies of the catalyst-ionomer interface and more applied investigations of structure-processing-performance correlations in PEM fuel cell and electrolyzer CLs.
- 10 May 2024
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 128 (20) , 8467-8482
Open AccessX-ray Photoelectron Spectroscopy Analysis of Nafion-Containing Samples: Pitfalls, Protocols, and Perceptions of Physicochemical Properties
X-ray photoelectron spectroscopy (XPS) is one of the most common techniques used to analyze the surface composition of catalysts and support materials used in polymer electrolyte membrane (PEM) fuel cells and electrolyzers, providing important insights for further improvement of their properties. Characterization of catalyst layers (CLs) is more challenging, which can be at least partially attributed to the instability of ionomer materials such as Nafion during measurements. This work explores the stability of Nafion during XPS measurements, illuminating and addressing Nafion degradation concerns. The extent of Nafion damage as a function of XPS instrumentation, measurement conditions, and sample properties was evaluated across multiple instruments. Results revealed that significant Nafion damage to the ion-conducting sulfonic acid species (>50% loss in sulfur signal) may occur in a relatively short time frame (tens of minutes) depending on the exact nature of the sample and XPS instrument. This motivated the development and validation of a multipoint XPS data acquisition protocol that minimizes Nafion damage, resulting in reliable data acquisition by avoiding significant artifacts from Nafion instability. The developed protocol was then used to analyze both thin film ionomer samples and Pt/C-based CLs. Comparison of PEM fuel cell CLs to Nafion thin films revealed several changes in Nafion spectral features attributed to charge transfer due to interaction with conductive catalyst and support species. This study provides a method to reliably characterize ionomer-containing samples, facilitating fundamental studies of the catalyst-ionomer interface and more applied investigations of structure-processing-performance correlations in PEM fuel cell and electrolyzer CLs.