Tomas Bulin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Tomas Bulin has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
C Ondrusek
Brno University of Technology, Faculty of Electrical Engineering and Communication, Technická 3058/10, 616 00 Brno, Czech Republic
2 shared publications- Eva Švábenská
Institute of Physics of Materials, AS CR, Brno, Czech Republic, EU
2 shared publications O. Schneeweiss
Institute of Physics of Materials ASCR, Žižkova 22, 616 62 Brno, Czech Republic
2 shared publications- Pavla Roupcová
Institute of Physics of Materials and CEITEC IPM, Czech Academy of Sciences, Žižkova 513/22, 616 00 Brno, Czech Republic
2 shared publications Cestmir Ondrusek
Brno University of Technology
1 shared publicationM Hapla
Institute of Physics of Materials ASCR, Žižkova 22, 616 62 Brno, Czech Republic
1 shared publication
Latest Publications
- Open Access
- 10 December 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 461 (1) , 012009
Analysis of stresses in FeSi sheets induced by laser cutting
The stresses induced by laser cutting in the non-oriented fully processed electrical FeSi sheets were investigated using X-ray diffraction, Mössbauer spectroscopy, and magnetic measurements. The magnetic measurements were used for studies of changes in magnetic properties due to changes in stresses. The original laser cut samples were compared with those after heat treatment. The magnetic measurements appeared as the most sensitive method among those selected for the present study. The influence of stresses has an impact on the shape of the hysteresis loops and the permeability in dependence on the excitation magnetic field. The selected heat treatment caused decrease of stresses and improvement of magnetic properties of the sheets.
- 10 December 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 461 (1) , 012009
Open AccessAnalysis of stresses in FeSi sheets induced by laser cutting
The stresses induced by laser cutting in the non-oriented fully processed electrical FeSi sheets were investigated using X-ray diffraction, Mössbauer spectroscopy, and magnetic measurements. The magnetic measurements were used for studies of changes in magnetic properties due to changes in stresses. The original laser cut samples were compared with those after heat treatment. The magnetic measurements appeared as the most sensitive method among those selected for the present study. The influence of stresses has an impact on the shape of the hysteresis loops and the permeability in dependence on the excitation magnetic field. The selected heat treatment caused decrease of stresses and improvement of magnetic properties of the sheets.
- 19 August 2017
- Published by Springer Nature
- p. 281-288
Magnetic Measurements of Solid Material
- 1 April 2017
- Published by Institute of Physics, Polish Academy of Sciences in Acta Physica Polonica A
- Vol. 131 (4) , 819-821
Magnetic Properties and Structure of Non-Oriented Electrical Steel Sheets after Different Shape Processing
- 1 April 2017
- Published by Institute of Physics, Polish Academy of Sciences in Acta Physica Polonica A
- Vol. 131 (4) , 819-821
Magnetic Properties and Structure of Non-Oriented Electrical Steel Sheets after Different Shape Processing
- Open Access
- 1 February 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 179 (1) , 012010
Magnetic properties of 42CrMo4 steel
Low alloyed high-grade chrome-molybdenum ferritic steel was investigated from the point of views of magnetic properties in dependence on heat and mechanical treatment. This steel can be used as components of magnetic circuits or some parts in electrical equipment. The basic information on structure and phase composition was obtained by optical and scanning electron microscopy, X-ray Powder Diffraction and Mössbauer Spectroscopy. The temperature stability of the material was proved by measurements of temperature dependences of magnetic moment. The magnetic parameters were obtained by measuring of magnetic hysteresis loops in dependence on saturation field and their frequencies. The results are discussed from the point of view of possible applications as a magnetic material in the very extremely environment, where high mechanical stresses and elevated temperatures can occur.
- 1 February 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 179 (1) , 012010
Open AccessMagnetic properties of 42CrMo4 steel
Low alloyed high-grade chrome-molybdenum ferritic steel was investigated from the point of views of magnetic properties in dependence on heat and mechanical treatment. This steel can be used as components of magnetic circuits or some parts in electrical equipment. The basic information on structure and phase composition was obtained by optical and scanning electron microscopy, X-ray Powder Diffraction and Mössbauer Spectroscopy. The temperature stability of the material was proved by measurements of temperature dependences of magnetic moment. The magnetic parameters were obtained by measuring of magnetic hysteresis loops in dependence on saturation field and their frequencies. The results are discussed from the point of view of possible applications as a magnetic material in the very extremely environment, where high mechanical stresses and elevated temperatures can occur.
- 3 November 2015
- Published by Springer Nature
- p. 441-446
Magnetic measurement of lamination punched with the press
- 3 November 2015
- Published by Springer Nature
- p. 441-446
Magnetic measurement of lamination punched with the press