Ricardo André Fiorotti Peixoto
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ricardo André Fiorotti Peixoto has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Júlia Castro Mendes
Universidade Federal de Juiz de Fora (UFJF)
3 shared publications - Guilherme Jorge Brigolini
Professor, Laboratório de Materiais de Construção Civil, Escola de Minas, Universidade Federal de Ouro Preto, Campus Universitário, Morro do Cruzeiro, 35400-000 Ouro Preto, Minas Gerais, Brazil
2 shared publications - José Maria Franco de Carvalho
Universidade Federal de Viçosa
2 shared publications - Ana Luiza Borges Marinho
Civil Engineer, Laboratório de Materiais de Construção Civil, Escola de Minas, Universidade Federal de Ouro Preto, Campus Universitário, Morro do Cruzeiro, 35400-000, Ouro Preto, Minas Gerais, Brazil
1 shared publication - Carina Miranda Mol Santos
Civil Engineer, Bachelor Student, Laboratório de Materiais de Construção Civil, Escola de Minas, Universidade Federal de Ouro Preto, Campus Universitário, Morro do Cruzeiro, 35400-000, Ouro Preto, Minas Gerais, Brazil
1 shared publication Deyvid Rr Gonçalves
Laboratory of Materials for Civil Construction, Federal University of Ouro Preto, Minas Gerais, Brazil
1 shared publication
Latest Publications
- 1 February 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 31 (2)
Low Environmental Impact Cement Produced Entirely from Industrial and Mining Waste
Proper disposal of industrial waste, the need to conserve nonrenewable resources, and high emissions are the major environmental issues at the present time. A significant portion of emissions from portland cement production is related to the energy required to maintain the clinker kiln at a temperature of approximately 1,450°C, which is necessary for alite formation. The alternative belite phase, however, requires lower temperatures for its formation (below 1,250°C). Although belite is less reactive than alite, it is equally efficient at higher hydration times. Thus, a belitic cement produced entirely with industrial waste (grits from the pulp and paper industry, steel slag, and quartzite mining tailings) is presented in this research. The raw meal was proportioned based on Bogue calculation and the firing was performed in a muffle furnace at a temperature of 1,250°C. A reference belitic cement was produced with limestone and clay under the same conditions. The results showed that both cements presented high belite contents and expected technological performance. The reference belitic cement revealed a higher reactivity, whereas the waste cement proved to be a technically feasible low-impact alternative.- 1 February 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 31 (2)
Low Environmental Impact Cement Produced Entirely from Industrial and Mining Waste
Proper disposal of industrial waste, the need to conserve nonrenewable resources, and high emissions are the major environmental issues at the present time. A significant portion of emissions from portland cement production is related to the energy required to maintain the clinker kiln at a temperature of approximately 1,450°C, which is necessary for alite formation. The alternative belite phase, however, requires lower temperatures for its formation (below 1,250°C). Although belite is less reactive than alite, it is equally efficient at higher hydration times. Thus, a belitic cement produced entirely with industrial waste (grits from the pulp and paper industry, steel slag, and quartzite mining tailings) is presented in this research. The raw meal was proportioned based on Bogue calculation and the firing was performed in a muffle furnace at a temperature of 1,250°C. A reference belitic cement was produced with limestone and clay under the same conditions. The results showed that both cements presented high belite contents and expected technological performance. The reference belitic cement revealed a higher reactivity, whereas the waste cement proved to be a technically feasible low-impact alternative.- 1 November 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 29 (11)
Ladle Furnace Slag as Binder for Cement-Based Composites
In recent years, the environmental facet of industrial waste management has become imperative. The recycling of these residues in the civil construction sector is growing, since both industries have developed an increasing concern for the exhaustion of natural resources. In this scenario, one example is the ladle furnace slag (LFS), a by-product of the secondary refining of steel. It is mainly composed of calcium and calcium magnesium silicates. Thus, this research aims to develop a sustainable binder obtained from LFS as a substitution of hydraulic lime. In this sense, an extensive characterization of the LFS was carried out in its raw and processed forms. Subsequently, all the requirements for hydrated lime and hydraulic lime were verified according to Brazilian and Portuguese standards. Finally, mortars for coating and laying were produced with portland cement, lime, and the sustainable binder, and their main properties were evaluated in the fresh and hardened states. The chemical and mechanical properties of the sustainable binder were closer to those of the hydraulic limes. The obtained results indicate the technical feasibility of the use of LFS as binder for mortars in the replacement of lime.
- 1 November 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 29 (11)
Ladle Furnace Slag as Binder for Cement-Based Composites
In recent years, the environmental facet of industrial waste management has become imperative. The recycling of these residues in the civil construction sector is growing, since both industries have developed an increasing concern for the exhaustion of natural resources. In this scenario, one example is the ladle furnace slag (LFS), a by-product of the secondary refining of steel. It is mainly composed of calcium and calcium magnesium silicates. Thus, this research aims to develop a sustainable binder obtained from LFS as a substitution of hydraulic lime. In this sense, an extensive characterization of the LFS was carried out in its raw and processed forms. Subsequently, all the requirements for hydrated lime and hydraulic lime were verified according to Brazilian and Portuguese standards. Finally, mortars for coating and laying were produced with portland cement, lime, and the sustainable binder, and their main properties were evaluated in the fresh and hardened states. The chemical and mechanical properties of the sustainable binder were closer to those of the hydraulic limes. The obtained results indicate the technical feasibility of the use of LFS as binder for mortars in the replacement of lime.
- Top Cited Papers
- 1 October 2016
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 28 (10)
Using Iron Ore Tailings from Tailing Dams as Road Material
The present work aims to evaluate the feasibility of iron ore tailings from tailing dams as an alternative material for road infrastructure. The iron ore tailings were characterized according to their chemical, mineralogical, environmental, and physical properties. Subsequently, the tailings were chemically stabilized using cement, lime, or steelmaking slag as binder. The tailing-cement, tailing-lime, and tailing-slag mixtures studied consisted of 1, 2, 5, and 10% binder content, each. The characterization methodology included chemical and mineralogical analysis through X-ray fluorescence and diffraction; environmental analysis with leaching and dissolution tests; evaluation of compaction curves; California bearing ratio (CBR) tests and expansion assessment; compressive strength, with curing in moisture chamber or at open air; water absorption; and evaluation of durability of the mixtures. Overall, the results indicate that the iron ore tailings are a feasible solution for use as layers for road p...
- 1 October 2016
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 28 (10)
Top Cited PapersUsing Iron Ore Tailings from Tailing Dams as Road Material
The present work aims to evaluate the feasibility of iron ore tailings from tailing dams as an alternative material for road infrastructure. The iron ore tailings were characterized according to their chemical, mineralogical, environmental, and physical properties. Subsequently, the tailings were chemically stabilized using cement, lime, or steelmaking slag as binder. The tailing-cement, tailing-lime, and tailing-slag mixtures studied consisted of 1, 2, 5, and 10% binder content, each. The characterization methodology included chemical and mineralogical analysis through X-ray fluorescence and diffraction; environmental analysis with leaching and dissolution tests; evaluation of compaction curves; California bearing ratio (CBR) tests and expansion assessment; compressive strength, with curing in moisture chamber or at open air; water absorption; and evaluation of durability of the mixtures. Overall, the results indicate that the iron ore tailings are a feasible solution for use as layers for road p...
- 3 December 2015
- Published by SAGE Publications in Waste Management & Research: The Journal for a Sustainable Circular Economy
- Vol. 34 (2) , 107-112
Evaluation of the economic feasibility of a processing plant for steelmaking slag
The utilisation of steelmaking slag as recycled aggregate for concretes is a widely investigated solution for mitigating the expenditure and environmental impacts of its storage. The Brazilian steel industry is investing in research and slag reprocessing practices, aiming to reuse most of its metallic fraction and properly allocate the non-metallic fraction, saving energy and reducing mining impacts. Research results demonstrate the technical and environmental feasibility of steel slag aggregates for civil construction. However, it is essential to evaluate whether the processing of the slag is economically feasible for this purpose. Economic analysis of the processing of steel slag was conducted through simulation – Monte Carlo method – in which it is possible to determine the risks and uncertainties inherent to the project. The costs that comprise the proposed project, from design through construction and operation itself, were estimated at US$2.8 million. The result of the simulation indicates economic feasibility of the project with 98% certainty, and an estimated profit of around 42%.
- 3 December 2015
- Published by SAGE Publications in Waste Management & Research: The Journal for a Sustainable Circular Economy
- Vol. 34 (2) , 107-112
Evaluation of the economic feasibility of a processing plant for steelmaking slag
The utilisation of steelmaking slag as recycled aggregate for concretes is a widely investigated solution for mitigating the expenditure and environmental impacts of its storage. The Brazilian steel industry is investing in research and slag reprocessing practices, aiming to reuse most of its metallic fraction and properly allocate the non-metallic fraction, saving energy and reducing mining impacts. Research results demonstrate the technical and environmental feasibility of steel slag aggregates for civil construction. However, it is essential to evaluate whether the processing of the slag is economically feasible for this purpose. Economic analysis of the processing of steel slag was conducted through simulation – Monte Carlo method – in which it is possible to determine the risks and uncertainties inherent to the project. The costs that comprise the proposed project, from design through construction and operation itself, were estimated at US$2.8 million. The result of the simulation indicates economic feasibility of the project with 98% certainty, and an estimated profit of around 42%.
- Open Access
- 1 September 2010
- Published by FapUNIFESP (SciELO) in Rem: Revista Escola de Minas
- Vol. 63 (3) , 523-528
Caracterização do resíduo de manta cerâmica usada para isolamento térmico e sua utilização na fabricação de argamassa
Esse trabalho tem os objetivos de caracterizar o resíduo de manta cerâmica, gerado no lingotamento contínuo dos aços, devido à diminuição da sua capacidade de isolamento térmico, e de estudar a viabilidade técnica da utilização desse resíduo na fabricação de argamassa. O resíduo foi submetido à análise química, difração de raios X e MEV e utilizado na preparação de argamassa. Foram feitas dosagens de 0%, 2%, e 6% em massa do resíduo, em substituição ao cimento, e realizado o ensaio de índice de consistência e compressão na argamassa. Dessa maneira, obtiveram-se resultados em três argamassas distintas. Os resultados indicam um aumento na resistência à compressão com adição do resíduo, em comparação com a argamassa-padrão, e o índice de consistência apresentou alterações pouco consideráveis.
- 1 September 2010
- Published by FapUNIFESP (SciELO) in Rem: Revista Escola de Minas
- Vol. 63 (3) , 523-528
Open AccessCaracterização do resíduo de manta cerâmica usada para isolamento térmico e sua utilização na fabricação de argamassa
Esse trabalho tem os objetivos de caracterizar o resíduo de manta cerâmica, gerado no lingotamento contínuo dos aços, devido à diminuição da sua capacidade de isolamento térmico, e de estudar a viabilidade técnica da utilização desse resíduo na fabricação de argamassa. O resíduo foi submetido à análise química, difração de raios X e MEV e utilizado na preparação de argamassa. Foram feitas dosagens de 0%, 2%, e 6% em massa do resíduo, em substituição ao cimento, e realizado o ensaio de índice de consistência e compressão na argamassa. Dessa maneira, obtiveram-se resultados em três argamassas distintas. Os resultados indicam um aumento na resistência à compressão com adição do resíduo, em comparação com a argamassa-padrão, e o índice de consistência apresentou alterações pouco consideráveis.