João Ribeiro
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
João Ribeiro has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Aldina Santiago
ISISE—Institute for Sustainability and Innovation in Structural, Department of Civil Engineering, University of Coimbra, 3030-788 Coimbra, Portugal
2 shared publications - Constança Rigueiro
Instituto Politécnico de Castelo Branco
2 shared publications - Hélder David Craveiro
Institute for Sustainability and Innovation in Structural Engineering, University of Coimbra, Coimbra
1 shared publication Ricardo Breda
ISISE – Civil Engineering Dept. Faculty of Sciences and Technology University of Coimbra Portugal
1 shared publication
Latest Publications
07.26: Structural analysis of C and I shaped cold‐formed steel columns
The market share of light steel framing construction using cold‐formed profiles has been increasing significantly in recent years; this solution is now recognized as suitable to be used as primary structural elements, particularly for residential and mid‐rise buildings. One of the main advantages of this construction typology is related to the very low weight of the individual elements which avoids the use of heavy lifting machinery. However, due to the reduced thickness of the individual plates that compose the cold‐formed steel columns (CFS) element cross‐section, CFS are susceptible to local and distortional buckling (or even a combination of both) in addition to the more common global element buckling, which may compromise their load carrying capacity.This paper explores the behaviour of two distinct CFS cross‐sections under compression, namely a single C section (lipped channel) and a built‐up I section composed of two lipped channels fastened back‐to‐back. The study briefly reports the experimental full scale tests undertaken at the University of Coimbra in order to assess the load carrying capacity of these columns, considering pinned boundary conditions, while comparing it to the design predictions according to the EN 1993‐1‐3; however, the main focus is on the development and validation of a finite element model enabling further parametric studies.The finite element model is developed with the commercial software ABAQUS using shell elements, and accounts for local, global and distortional geometric imperfections; material non‐linearity is also included based on material characterization previously conducted, and implemented following the Ramberg‐Osgood model. The model is found to be reliable in establishing the buckling loads and the buckling failure modes. A combination of flexural buckling about the minor axis in interaction with distortional buckling at mid‐height of the columns is found to be the main collapse mode, as observed in the experimental tests. The parametric study considers thickness and element length variation.
07.26: Structural analysis of C and I shaped cold‐formed steel columns
The market share of light steel framing construction using cold‐formed profiles has been increasing significantly in recent years; this solution is now recognized as suitable to be used as primary structural elements, particularly for residential and mid‐rise buildings. One of the main advantages of this construction typology is related to the very low weight of the individual elements which avoids the use of heavy lifting machinery. However, due to the reduced thickness of the individual plates that compose the cold‐formed steel columns (CFS) element cross‐section, CFS are susceptible to local and distortional buckling (or even a combination of both) in addition to the more common global element buckling, which may compromise their load carrying capacity.This paper explores the behaviour of two distinct CFS cross‐sections under compression, namely a single C section (lipped channel) and a built‐up I section composed of two lipped channels fastened back‐to‐back. The study briefly reports the experimental full scale tests undertaken at the University of Coimbra in order to assess the load carrying capacity of these columns, considering pinned boundary conditions, while comparing it to the design predictions according to the EN 1993‐1‐3; however, the main focus is on the development and validation of a finite element model enabling further parametric studies.The finite element model is developed with the commercial software ABAQUS using shell elements, and accounts for local, global and distortional geometric imperfections; material non‐linearity is also included based on material characterization previously conducted, and implemented following the Ramberg‐Osgood model. The model is found to be reliable in establishing the buckling loads and the buckling failure modes. A combination of flexural buckling about the minor axis in interaction with distortional buckling at mid‐height of the columns is found to be the main collapse mode, as observed in the experimental tests. The parametric study considers thickness and element length variation.
09.10: Shear damage evaluation of bolted steel joints
The purpose of this study is to address a way of predicting the ductility capacity of steel joints. Recent research studies show that a joints’ ability to perform under elevated deformations, without fracturing, is a key factor in enabling mechanisms preventing collapse to be developed, and thus, improve the overall robustness of steel framed structures. This theme is becoming rather timely as building owners and insurers try to assess the collapse risk of their buildings, and the probability of a wide spread collapse if subjected to extreme events, either due to natural or terrorist causes. However, regarding this matter, current design code guidelines are limited to a prescriptive approach, by recommending a nominal tying force to be met, or quantifying a force that reproduces accidental scenarios, such as an impact of a vehicle, ships or helicopters, which do not address the overall behavior and performance of the structure.This paper presents an evaluation of the shear damage state of a bolted steel joint. For that, it is necessary to establish the shear damage parameters that are required to numerically obtain the rupture of steel elements, allowing the prediction of the ductility of steel joints. Previous authors’ research has showed that a ductile damage model may be insufficient to capture its end‐plate fracture and to establish a joints’ rupture. Hence, this study looks forward to improve the damage threshold for smaller triaxial stress states, within the shear and compression zones.In order to achieve this objective, a finite element model is developed and compared with real scale test results of a bolted steel joint under bending. The numerical model takes into account the strain softening of the material by means of a continuum damage mechanics approach and making use of the “element deletion” technique to approximate the fracture pattern of the studied joint. The analyses are carried out using the finite element software ABAQUS.
09.10: Shear damage evaluation of bolted steel joints
The purpose of this study is to address a way of predicting the ductility capacity of steel joints. Recent research studies show that a joints’ ability to perform under elevated deformations, without fracturing, is a key factor in enabling mechanisms preventing collapse to be developed, and thus, improve the overall robustness of steel framed structures. This theme is becoming rather timely as building owners and insurers try to assess the collapse risk of their buildings, and the probability of a wide spread collapse if subjected to extreme events, either due to natural or terrorist causes. However, regarding this matter, current design code guidelines are limited to a prescriptive approach, by recommending a nominal tying force to be met, or quantifying a force that reproduces accidental scenarios, such as an impact of a vehicle, ships or helicopters, which do not address the overall behavior and performance of the structure.This paper presents an evaluation of the shear damage state of a bolted steel joint. For that, it is necessary to establish the shear damage parameters that are required to numerically obtain the rupture of steel elements, allowing the prediction of the ductility of steel joints. Previous authors’ research has showed that a ductile damage model may be insufficient to capture its end‐plate fracture and to establish a joints’ rupture. Hence, this study looks forward to improve the damage threshold for smaller triaxial stress states, within the shear and compression zones.In order to achieve this objective, a finite element model is developed and compared with real scale test results of a bolted steel joint under bending. The numerical model takes into account the strain softening of the material by means of a continuum damage mechanics approach and making use of the “element deletion” technique to approximate the fracture pattern of the studied joint. The analyses are carried out using the finite element software ABAQUS.
- Open Access
- 1 January 2017
- Published by Elsevier in Procedia Engineering
- Vol. 199, 2494-2499
Numerical assessment of the behaviour of a fixed offshore platform subjected to ship collision
- 1 January 2017
- Published by Elsevier in Procedia Engineering
- Vol. 199, 2494-2499
Open AccessNumerical assessment of the behaviour of a fixed offshore platform subjected to ship collision