Souhir Gara
Research Subjects
Souhir Gara has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Oleg Tsoumarev
ENIT—BP 37
6 shared publicationsM. Ben Amar
Laboratoire des Systèmes ElectroMécaniques, LASEM, ENIS, Tunisie, Tunisia
1 shared publicationM. Hbaieb
Laboratoire de Génie de Production Mécanique et Matériaux, LGPM2, ENIS, Tunisie, Tunisia
1 shared publicationRamzi Fredj
1 shared publicationSami Naîmi
1 shared publicationSamir M'Hamed
Department of Mechanical Engineering, Institut Supérieur des Etudes Technologiques de Nabeul, Nabeul, Tunisia
1 shared publication
Latest Publications
- 8 December 2017
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 95 (9-12) , 3227-3242
Optimization of cutting conditions in slotting of multidirectional CFRP laminate
- 8 December 2017
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 95 (9-12) , 3227-3242
Optimization of cutting conditions in slotting of multidirectional CFRP laminate
- 5 October 2017
- Published by Taylor & Francis in Machining Science and Technology
- Vol. 22 (2) , 320-337
Temperature measurement and machining damage in slotting of multidirectional CFRP laminate
Compared to metallic materials, carbon fiber-reinforced plastics (CFRPs) have lower thermal conductivity and minor thermal expansion coefficient. Despite this, their machining can generate accuracy errors if the cutting temperature is not controlled. In this paper, an experimental study of slotting of multidirectional CFRP laminate (G803/914) with three micrograin carbide burr tools with different geometries is considered in order to investigate tool-workpiece contact point temperature, chip temperature, machined surface damage, subsurface defects and tool degradation. The experiment is made on a computer numerical control (CNC) machine with cutting speed ranging from 80 to 200 m/min and feed per tooth from 0.008 to 0.060 mm/rev/tooth. The data were analyzed in order to establish empirical models showing the dependence of cutting temperature on tool geometry and cutting conditions. Based on the results, it is concluded that cutting speed is the factor influencing cutting temperature the most, the heat generated during slotting is removed mainly by chips and the chip temperature is greater than the tool-workpiece contact temperature of about 18.5°C on average for the three burr tools.
- 5 October 2017
- Published by Taylor & Francis in Machining Science and Technology
- Vol. 22 (2) , 320-337
Temperature measurement and machining damage in slotting of multidirectional CFRP laminate
Compared to metallic materials, carbon fiber-reinforced plastics (CFRPs) have lower thermal conductivity and minor thermal expansion coefficient. Despite this, their machining can generate accuracy errors if the cutting temperature is not controlled. In this paper, an experimental study of slotting of multidirectional CFRP laminate (G803/914) with three micrograin carbide burr tools with different geometries is considered in order to investigate tool-workpiece contact point temperature, chip temperature, machined surface damage, subsurface defects and tool degradation. The experiment is made on a computer numerical control (CNC) machine with cutting speed ranging from 80 to 200 m/min and feed per tooth from 0.008 to 0.060 mm/rev/tooth. The data were analyzed in order to establish empirical models showing the dependence of cutting temperature on tool geometry and cutting conditions. Based on the results, it is concluded that cutting speed is the factor influencing cutting temperature the most, the heat generated during slotting is removed mainly by chips and the chip temperature is greater than the tool-workpiece contact temperature of about 18.5°C on average for the three burr tools.
- 17 August 2017
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 94 (1-4) , 687-699
Theoretical and experimental study of slotting CFRP material with segmented helix tool
- 17 August 2017
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 94 (1-4) , 687-699
Theoretical and experimental study of slotting CFRP material with segmented helix tool
- 1 September 2016
- Published by Elsevier in Measurement
- Vol. 91, 414-420
Prediction of surface roughness in slotting of CFRP
- 1 September 2016
- Published by Elsevier in Measurement
- Vol. 91, 414-420
Prediction of surface roughness in slotting of CFRP
- 20 August 2016
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 89 (9-12) , 3379-3391
Prediction of cutting forces in slotting of multidirectional CFRP laminate
- 20 August 2016
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 89 (9-12) , 3379-3391
Prediction of cutting forces in slotting of multidirectional CFRP laminate
- 15 December 2015
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 86 (1-4) , 451-461
Effect of tool geometry on surface roughness in slotting of CFRP
- 15 December 2015
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 86 (1-4) , 451-461
Effect of tool geometry on surface roughness in slotting of CFRP
- 31 May 2008
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 40 (9-10) , 971-981
Cost and time calculation in rough NC turning
- 31 May 2008
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 40 (9-10) , 971-981
Cost and time calculation in rough NC turning