Everaldo De Barros
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Everaldo De Barros has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Carlos D Andrade Souto
Instituto de Aeronáutica e Espaço, Brasil
3 shared publications - Fernando Juliani
School of Engineering, São Paulo State University, Guaratinguetá, Brazil
1 shared publication Leandro Ribeiro De Camargo
Exploração e Produção / Construção e Manutenção de Poços Marítimos, Santos, Brasil
1 shared publication- Leandro Ribeiro de Camargo
Offshore Well Construction and Maintenance, Petróleo Brasileiro S.A., Santos, Brazil
1 shared publication Mauro Hugo Mathias
Universidade Estadual Paulista “Júlio de Mesquita Filho”, Guaratinguetá, Brasil
1 shared publication- Mauro Hugo Mathias1 shared publication
Latest Publications
- 6 March 2017
- Published by Emerald Publishing in Aircraft Engineering and Aerospace Technology
- Vol. 89 (2) , 358-363
Experimental facilities for modal testing
Purpose: The experimental modal analysis requires good knowledge of various engineering fields, such as mechanical vibrations, transducers used in vibration measurement, transducers and system calibration methods, data acquisition systems, digital signal processing and system identification. Test facilities constitute a key factor for improving the quality of the estimated modal model. This paper aims to describe the experimental facilities at the Institute of Aeronautics and Space (IAE) Modal Testing Laboratory in terms of associated instrumentation and data acquisition system, metrological aspects and computational resources. The discussion is completed with a practical application showing a ground vibration testing (GVT) of an unmanned aerial vehicle (UAV). Design/methodology/approach: The experimental facilities were evaluated in a typical GVT, using three shakers in both vertical and horizontal excitations and 88 response measurement points. The global excitation method was used to excite all desired modes. The reliability of the experimental modal model was validated by an auto modal assurance criterion matrix for the measured modes of the structure. Findings: The experimental facilities were successfully used for validating the dynamical characteristics of the UAV under testing. Originality/value: The modal test facilities of the Modal Testing Laboratory at the IAE, the main research center of the Brazilian Air Force, are described in this paper.
- 6 March 2017
- Published by Emerald Publishing in Aircraft Engineering and Aerospace Technology
- Vol. 89 (2) , 358-363
Experimental facilities for modal testing
Purpose: The experimental modal analysis requires good knowledge of various engineering fields, such as mechanical vibrations, transducers used in vibration measurement, transducers and system calibration methods, data acquisition systems, digital signal processing and system identification. Test facilities constitute a key factor for improving the quality of the estimated modal model. This paper aims to describe the experimental facilities at the Institute of Aeronautics and Space (IAE) Modal Testing Laboratory in terms of associated instrumentation and data acquisition system, metrological aspects and computational resources. The discussion is completed with a practical application showing a ground vibration testing (GVT) of an unmanned aerial vehicle (UAV). Design/methodology/approach: The experimental facilities were evaluated in a typical GVT, using three shakers in both vertical and horizontal excitations and 88 response measurement points. The global excitation method was used to excite all desired modes. The reliability of the experimental modal model was validated by an auto modal assurance criterion matrix for the measured modes of the structure. Findings: The experimental facilities were successfully used for validating the dynamical characteristics of the UAV under testing. Originality/value: The modal test facilities of the Modal Testing Laboratory at the IAE, the main research center of the Brazilian Air Force, are described in this paper.
- Open Access
- 1 December 2015
- Published by Walter de Gruyter GmbH in Metrology and Measurement Systems
- Vol. 22 (4) , 559-564
Experimental Observation Of Nonlinear Vibrations Using A Closed-Loop Vibration System
This paper presents experimental observation of nonlinear vibrations in the response of a flexible cantilever beam to transverse harmonic base excitations around its flexural mode frequencies. In the experimental setup, instead of manual control of the signal excitation frequency and amplitude, a closed-loop vibration system is used to keep the excitation amplitude constant during the frequency sweep and to increase confidence in the experimental results. The experimental results show the presence of the third mode in the response when varying the excitation frequency around the fourth mode. The frequency-response curves, response spectrum and Poincaré plots were used for characterization of nonlinear dynamic behaviour of the beam.
- 1 December 2015
- Published by Walter de Gruyter GmbH in Metrology and Measurement Systems
- Vol. 22 (4) , 559-564
Open AccessExperimental Observation Of Nonlinear Vibrations Using A Closed-Loop Vibration System
This paper presents experimental observation of nonlinear vibrations in the response of a flexible cantilever beam to transverse harmonic base excitations around its flexural mode frequencies. In the experimental setup, instead of manual control of the signal excitation frequency and amplitude, a closed-loop vibration system is used to keep the excitation amplitude constant during the frequency sweep and to increase confidence in the experimental results. The experimental results show the presence of the third mode in the response when varying the excitation frequency around the fourth mode. The frequency-response curves, response spectrum and Poincaré plots were used for characterization of nonlinear dynamic behaviour of the beam.
- Open Access
- 1 December 2015
- Published by FapUNIFESP (SciELO) in Revista Brasileira de Ensino de Física
- Vol. 37 (4) , 4313-1
Application of a computer sound card for measurement of mechanical vibrations
This paper presents a data acquisition and analysis system based on a computer sound card for measuring and processing random vibration signals. This system turns the computer into a two-channel measurement instrument which provides sample rate, simultaneous sampling, frequency range, filters and others essential capabilities required to perform random vibrations measurements. An easy-to-use software was developed for vibration monitoring and analysis, including facilities for data recording, digital signal processing and real time spectrum analyzer. Since the tasks of vibration data acquisition frequently require expensive hardware and software, this versatile system provides students a very accurate and inexpensive solution for experimental studying mechanical vibrations.
- 1 December 2015
- Published by FapUNIFESP (SciELO) in Revista Brasileira de Ensino de Física
- Vol. 37 (4) , 4313-1
Open AccessApplication of a computer sound card for measurement of mechanical vibrations
This paper presents a data acquisition and analysis system based on a computer sound card for measuring and processing random vibration signals. This system turns the computer into a two-channel measurement instrument which provides sample rate, simultaneous sampling, frequency range, filters and others essential capabilities required to perform random vibrations measurements. An easy-to-use software was developed for vibration monitoring and analysis, including facilities for data recording, digital signal processing and real time spectrum analyzer. Since the tasks of vibration data acquisition frequently require expensive hardware and software, this versatile system provides students a very accurate and inexpensive solution for experimental studying mechanical vibrations.