Punit Arora
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Punit Arora has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Jayanta Chattopadhyay
Engineering Sciences Homi Bhabha National Institute Mumbai India
5 shared publications Suneel K. Gupta
Engineering Sciences Homi Bhabha National Institute Mumbai India
5 shared publications- Suneel.K. Gupta
Department of Engineering Sciences Homi Bhabha National Institute (HBNI) Mumbai India
2 shared publications D. K. Sahoo
Board of Radiation and Isotope Technology
1 shared publicationGargi Choudhuri
Bhabha Atomic Research Centre
1 shared publicationH.S. Kushwaha
1 shared publication
Latest Publications
- 25 January 2025
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 48 (4) , 1712-1724
Proposing a New Crack Driving Force Parameter for Fatigue Crack Growth Rate of C–Mn Steel
The present study is aimed at analyzing the fatigue crack growth rate data on compact tension (CT) and three‐point‐bend (TPB) specimens of C–Mn steel under different positive load ratios. Detailed elastic–plastic finite element analyses have been performed using nonlinear kinematic hardening rule of Chaboche material model. The numerically calculated plastic zone ahead of crack tip has been compared with measured plastic zone using digital image correlation technique. The fatigue crack growth rate curves have been analyzed with respect to different crack driving forces such as (i) single‐parameter stress intensity factor (SIF) range, (ii) two‐parameter‐based SIF ( ), and (iii) cyclic plasticity zone–based models. A new crack driving force has been proposed considering cyclic plastic zone and representative plastic strain accumulation within this zone. The parameter and proposed model resulted in improved assessments for different load ratios and constraint geometries (CT and TPB).
- 25 January 2025
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 48 (4) , 1712-1724
Proposing a New Crack Driving Force Parameter for Fatigue Crack Growth Rate of C–Mn Steel
The present study is aimed at analyzing the fatigue crack growth rate data on compact tension (CT) and three‐point‐bend (TPB) specimens of C–Mn steel under different positive load ratios. Detailed elastic–plastic finite element analyses have been performed using nonlinear kinematic hardening rule of Chaboche material model. The numerically calculated plastic zone ahead of crack tip has been compared with measured plastic zone using digital image correlation technique. The fatigue crack growth rate curves have been analyzed with respect to different crack driving forces such as (i) single‐parameter stress intensity factor (SIF) range, (ii) two‐parameter‐based SIF ( ), and (iii) cyclic plasticity zone–based models. A new crack driving force has been proposed considering cyclic plastic zone and representative plastic strain accumulation within this zone. The parameter and proposed model resulted in improved assessments for different load ratios and constraint geometries (CT and TPB).
- 15 January 2025
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 48 (4) , 1589-1611
Effect of Strain Gradients on Fatigue Life of C‐Mn Steel Notched Tubes Under Axial and Torsion Loads: Tests and Analyses
Present study aims to investigate individual effects of strain gradient and peak equivalent strain amplitude on fatigue life of notched tubes of C‐Mn steel. Remote pure axial and pure torsion strain‐controlled tests have been performed for different strain gradients (owing to different hole diameter in tube specimen) subjected to same peak equivalent strain amplitude at hole tip. During the tests, local strains ahead of notch were measured using digital image correlation/strain gauge techniques. Measured strains have been compared with simulated strains using detailed finite element analyses. Additionally, fatigue life assessment has also been carried out using equivalent strain amplitude at (i) peak strain location and (ii) different distances from peak strain location. A critical distance parameter ( d c ), in present study, has been deduced based on least scatter between predicted and test fatigue lives.
- 15 January 2025
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 48 (4) , 1589-1611
Effect of Strain Gradients on Fatigue Life of C‐Mn Steel Notched Tubes Under Axial and Torsion Loads: Tests and Analyses
Present study aims to investigate individual effects of strain gradient and peak equivalent strain amplitude on fatigue life of notched tubes of C‐Mn steel. Remote pure axial and pure torsion strain‐controlled tests have been performed for different strain gradients (owing to different hole diameter in tube specimen) subjected to same peak equivalent strain amplitude at hole tip. During the tests, local strains ahead of notch were measured using digital image correlation/strain gauge techniques. Measured strains have been compared with simulated strains using detailed finite element analyses. Additionally, fatigue life assessment has also been carried out using equivalent strain amplitude at (i) peak strain location and (ii) different distances from peak strain location. A critical distance parameter ( d c ), in present study, has been deduced based on least scatter between predicted and test fatigue lives.
- 17 January 2023
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 46 (4) , 1330-1356
Comparing fatigue life prediction capability of critical plane models using multiaxial test database on 17 materials
The present study validates recent as well as extensively used critical plane (CP)‐based fatigue life assessment models for 10 ferrous and 7 non‐ferrous materials. Fourteen CP models, including recently reported in‐house developed model, have been analyzed. These models use resolved stresses, strains, strain energy density, and combinations of stresses and strains to identify critical plane and quantify fatigue damage. The loading conditions cover various proportional and non‐proportional axial‐torsion strain paths with different phase shift angles with (or without) mean stress/strain component(s), loading waveforms, and asynchronous axial‐torsion stain paths. The comparative study brought out the goodness of various models by quantifying the extent of scatter and computational time.Some of the strain energy density‐based models (including in‐house model) have been shortlisted, which produced accurate fatigue life assessments. Among the shortlisted models, in‐house model is free from the calculation subjectivities of resultant shear and performs faster fatigue damage calculations.
- 17 January 2023
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 46 (4) , 1330-1356
Comparing fatigue life prediction capability of critical plane models using multiaxial test database on 17 materials
The present study validates recent as well as extensively used critical plane (CP)‐based fatigue life assessment models for 10 ferrous and 7 non‐ferrous materials. Fourteen CP models, including recently reported in‐house developed model, have been analyzed. These models use resolved stresses, strains, strain energy density, and combinations of stresses and strains to identify critical plane and quantify fatigue damage. The loading conditions cover various proportional and non‐proportional axial‐torsion strain paths with different phase shift angles with (or without) mean stress/strain component(s), loading waveforms, and asynchronous axial‐torsion stain paths. The comparative study brought out the goodness of various models by quantifying the extent of scatter and computational time.Some of the strain energy density‐based models (including in‐house model) have been shortlisted, which produced accurate fatigue life assessments. Among the shortlisted models, in‐house model is free from the calculation subjectivities of resultant shear and performs faster fatigue damage calculations.
- 7 February 2022
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 45 (4) , 1145-1164
Validation of notch stress estimation schemes for low C–Mn steel
The present study is aimed at validation of notch stress/strain estimation schemes such as classical Neuber, Hoffmann–Seeger, and recently developed Ince–Glinka method for nuclear piping material (low C–Mn steel). The study has considered different constraints, loading conditions, and various hole sizes to accommodate strain gradient variations and equivalent peak strains. The notch stress field evaluated using these schemes is compared with corresponding stress using elastic–plastic finite element (FE) analyses. The comparisons have brought out that the Hoffmann–Seeger scheme results in reasonably accurate assessment of stress localization nearly for all constraint geometries, loadings, and strain gradients. However, the classical Neuber scheme is more suitable for low constraint geometries and intermediate constraint geometries, whereas it results in underestimation of maximum principal stress for high constraint geometries, thereby leading to overprediction of fatigue life. Further, the suitability of energy equivalence equations of Ince–Glinka model for individual stress components has been reviewed.
- 7 February 2022
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 45 (4) , 1145-1164
Validation of notch stress estimation schemes for low C–Mn steel
The present study is aimed at validation of notch stress/strain estimation schemes such as classical Neuber, Hoffmann–Seeger, and recently developed Ince–Glinka method for nuclear piping material (low C–Mn steel). The study has considered different constraints, loading conditions, and various hole sizes to accommodate strain gradient variations and equivalent peak strains. The notch stress field evaluated using these schemes is compared with corresponding stress using elastic–plastic finite element (FE) analyses. The comparisons have brought out that the Hoffmann–Seeger scheme results in reasonably accurate assessment of stress localization nearly for all constraint geometries, loadings, and strain gradients. However, the classical Neuber scheme is more suitable for low constraint geometries and intermediate constraint geometries, whereas it results in underestimation of maximum principal stress for high constraint geometries, thereby leading to overprediction of fatigue life. Further, the suitability of energy equivalence equations of Ince–Glinka model for individual stress components has been reviewed.
- 2 October 2020
- Published by Springer Nature
- p. 227-247
Assessment of Cyclic Plasticity Behaviour of Primary Piping Material of Indian PHWRs Under Multiaxial Loading Scenario
- 2 October 2020
- Published by Springer Nature
- p. 227-247
Assessment of Cyclic Plasticity Behaviour of Primary Piping Material of Indian PHWRs Under Multiaxial Loading Scenario
- 16 February 2020
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 43 (7) , 1327-1352
Validating generality of recently developed critical plane model for fatigue life assessments using multiaxial test database on seventeen different materials
The present studies are aimed at validation of a newly developed critical plane model with respect to large variety of engineering materials used for different applications. This newly developed model has been recently reported by present authors. To strengthen general applicability of this model, multiaxial test database consisting of a wide variety of multiaxial loading paths have been considered. The strain paths include pure axial, pure torsion, in‐phase axial‐torsion, out‐of‐phase axial‐torsion with phase shift angles varying from 30° to 180° having sine/trapezoidal/triangular strain waveforms, with/without mean axial/shear strains and asynchronous axial‐torsion strain paths of different frequency ratios etc.The materials covered in present study are mainly categorized as ferrous and nonferrous alloys. In ferrous alloy category, material grades from plain carbon steel (mild steel, 16MnR, SA333 Gr. 6, E235 and E355), low‐alloy steel (1Cr‐Mo‐V and S460 N) and austenitic stainless steel (SS304, SS316L and SS347) have been considered. In nonferrous alloy category, aluminium alloys (2024T3‐Al, 7075T651‐Al, and PA38‐T6‐Al), titanium (pure titanium and TC4 alloy), cobalt base super‐alloy (Haynes 188), and nickel alloy (Inconel‐718) have been considered.The predicted and test fatigue lives are found in good agreement for all these materials and complex multiaxial loading paths.
- 16 February 2020
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 43 (7) , 1327-1352
Validating generality of recently developed critical plane model for fatigue life assessments using multiaxial test database on seventeen different materials
The present studies are aimed at validation of a newly developed critical plane model with respect to large variety of engineering materials used for different applications. This newly developed model has been recently reported by present authors. To strengthen general applicability of this model, multiaxial test database consisting of a wide variety of multiaxial loading paths have been considered. The strain paths include pure axial, pure torsion, in‐phase axial‐torsion, out‐of‐phase axial‐torsion with phase shift angles varying from 30° to 180° having sine/trapezoidal/triangular strain waveforms, with/without mean axial/shear strains and asynchronous axial‐torsion strain paths of different frequency ratios etc.The materials covered in present study are mainly categorized as ferrous and nonferrous alloys. In ferrous alloy category, material grades from plain carbon steel (mild steel, 16MnR, SA333 Gr. 6, E235 and E355), low‐alloy steel (1Cr‐Mo‐V and S460 N) and austenitic stainless steel (SS304, SS316L and SS347) have been considered. In nonferrous alloy category, aluminium alloys (2024T3‐Al, 7075T651‐Al, and PA38‐T6‐Al), titanium (pure titanium and TC4 alloy), cobalt base super‐alloy (Haynes 188), and nickel alloy (Inconel‐718) have been considered.The predicted and test fatigue lives are found in good agreement for all these materials and complex multiaxial loading paths.
- 27 December 2017
- Published by Springer Nature
- p. 611-622
Effect of Loading Frequency on the Fatigue Crack Growth Rate of Type 304L(N) Material
- 27 December 2017
- Published by Springer Nature
- p. 611-622
Effect of Loading Frequency on the Fatigue Crack Growth Rate of Type 304L(N) Material