Dominik Kueres
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dominik Kueres has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Josef Hegger
RWTH Aachen University
24 shared publications - Martin Classen
RWTH Aachen University
13 shared publications - Martin Herbrand
WTM Engineers GmbH Johannisbollwerk 6–8 20459 Hamburg
8 shared publications - Carsten Siburg
H+P Ingenieure GmbH 52072 Aachen Kackertstraße 10
5 shared publications Josef Hegger
Professor, Institute of Structural Concrete, RWTH Aachen University, Germany
4 shared publications- Alexander Stark
Institute of Concrete Structures and Building Materials, Karlsruhe Institute of Technology, Karlsruhe, Germany
3 shared publications
Latest Publications
- 1 December 2020
- Published by Emerald Publishing in Magazine of Concrete Research
- Vol. 72 (23) , 1189-1202
Punching strength of continuous concrete slabs
Punching tests on continuous concrete slabs are very expensive and elaborate. As a consequence, the majority of the existing punching tests have been performed on isolated specimens representing only the hogging moment region around the considered slab–column connection. Isolated punching tests are valuable in order to analyse the punching shear behaviour systematically. Nevertheless, beneficial effects of slabs' continuity (e.g. moment redistributions and membrane actions) may not occur in these tests. To investigate the punching shear behaviour of continuous concrete slabs, in this paper the existing two-parameter kinematic theory for punching shear in reinforced and prestressed concrete slabs is applied. The beneficial effects of slab continuity on punching strength are estimated based on a theoretical model described in the literature. The kinematic theory is applied to evaluate punching tests on a continuous slab, revealing good agreement between predictions and experimental results. As only few punching tests on continuous slabs are available, further parametric studies are performed to analyse the effects of slab continuity on punching strength in more detail. The results suggest higher punching shear capacities for continuous slabs than for isolated slabs. Nevertheless, the beneficial influences of slab continuity on punching strength strongly depend on the slab stiffness and flexural cracking.
- 1 December 2020
- Published by Emerald Publishing in Magazine of Concrete Research
- Vol. 72 (23) , 1189-1202
Punching strength of continuous concrete slabs
Punching tests on continuous concrete slabs are very expensive and elaborate. As a consequence, the majority of the existing punching tests have been performed on isolated specimens representing only the hogging moment region around the considered slab–column connection. Isolated punching tests are valuable in order to analyse the punching shear behaviour systematically. Nevertheless, beneficial effects of slabs' continuity (e.g. moment redistributions and membrane actions) may not occur in these tests. To investigate the punching shear behaviour of continuous concrete slabs, in this paper the existing two-parameter kinematic theory for punching shear in reinforced and prestressed concrete slabs is applied. The beneficial effects of slab continuity on punching strength are estimated based on a theoretical model described in the literature. The kinematic theory is applied to evaluate punching tests on a continuous slab, revealing good agreement between predictions and experimental results. As only few punching tests on continuous slabs are available, further parametric studies are performed to analyse the effects of slab continuity on punching strength in more detail. The results suggest higher punching shear capacities for continuous slabs than for isolated slabs. Nevertheless, the beneficial influences of slab continuity on punching strength strongly depend on the slab stiffness and flexural cracking.
- 1 June 2020
- Published by Emerald Publishing in Magazine of Concrete Research
- Vol. 72 (12) , 595-609
Two-parameter kinematic theory for punching shear in prestressed concrete slabs
According to previous investigations, prestressing has various positive influences on punching shear behaviour of reinforced-concrete slabs. While in-plane compressive stresses and decompression moments reduce the slab deformations, leading to an increased punching strength, the vertical component of inclined tendons inside the failure surface reduces the acting shear force. To allow for a realistic prediction of the punching strength of prestressed concrete slabs, these positive influences must be taken into account. In this paper, the existing two-parameter kinematic theory for punching shear in reinforced-concrete slabs without shear reinforcement is extended to consider the beneficial effects of prestressing on punching strength. The effects are investigated separately by means of punching tests with predefined edge conditions (e.g. in-plane or rotational restraint of slab edges) reported in literature. Also, the influences of arrangement and inclination of tendons on punching shear resistance are investigated. Finally, the extended theory is validated using both systematic punching test series and databank evaluations.
- 1 June 2020
- Published by Emerald Publishing in Magazine of Concrete Research
- Vol. 72 (12) , 595-609
Two-parameter kinematic theory for punching shear in prestressed concrete slabs
According to previous investigations, prestressing has various positive influences on punching shear behaviour of reinforced-concrete slabs. While in-plane compressive stresses and decompression moments reduce the slab deformations, leading to an increased punching strength, the vertical component of inclined tendons inside the failure surface reduces the acting shear force. To allow for a realistic prediction of the punching strength of prestressed concrete slabs, these positive influences must be taken into account. In this paper, the existing two-parameter kinematic theory for punching shear in reinforced-concrete slabs without shear reinforcement is extended to consider the beneficial effects of prestressing on punching strength. The effects are investigated separately by means of punching tests with predefined edge conditions (e.g. in-plane or rotational restraint of slab edges) reported in literature. Also, the influences of arrangement and inclination of tendons on punching shear resistance are investigated. Finally, the extended theory is validated using both systematic punching test series and databank evaluations.
- 5 September 2019
- Published by Springer Nature
- p. 503-514
New Punching Shear Reinforcement System for Footings and Ground Slabs
- 5 September 2019
- Published by Springer Nature
- p. 503-514
New Punching Shear Reinforcement System for Footings and Ground Slabs
- 9 May 2019
- Published by Wiley in Structural Concrete
- Vol. 21 (1) , 235-246
Punching shear behavior of reinforced concrete flat slabs with a varying amount of shear reinforcement
The punching shear design procedures according to current codes (e.g., Eurocode 2 or Model Code 2010) are similar. However, the predicted punching shear capacities may differ significantly depending on the background (e.g., semi‐empirical or physical) of the design provisions and the considered influences. For the evaluation and improvement of the existing provisions for flat slabs without and with high amounts of shear reinforcement, a large number of punching test series on reinforced concrete flat slabs is available in the literature. Nevertheless, the evaluation of the code equations for the design of the shear reinforcement (failure inside the shear‐reinforced zone) is still not possible since only few punching tests on flat slabs with low and medium amounts of shear reinforcement have been conducted.To investigate the punching shear behavior of flat slabs with a varying amount of shear reinforcement, three systematic test series without and with stirrups as shear reinforcement were conducted. The experimental program included three reference tests without and eight tests with low and medium amounts of shear reinforcement. In the tests, the amount of shear reinforcement was varied by changing the stirrup diameter only. Further investigated influences were the shear span‐depth ratio and the effective depth. The results of the test series are discussed and compared to the predictions according to Eurocode 2, Model Code 2010 and the draft of the second generation of Eurocode 2.
- 9 May 2019
- Published by Wiley in Structural Concrete
- Vol. 21 (1) , 235-246
Punching shear behavior of reinforced concrete flat slabs with a varying amount of shear reinforcement
The punching shear design procedures according to current codes (e.g., Eurocode 2 or Model Code 2010) are similar. However, the predicted punching shear capacities may differ significantly depending on the background (e.g., semi‐empirical or physical) of the design provisions and the considered influences. For the evaluation and improvement of the existing provisions for flat slabs without and with high amounts of shear reinforcement, a large number of punching test series on reinforced concrete flat slabs is available in the literature. Nevertheless, the evaluation of the code equations for the design of the shear reinforcement (failure inside the shear‐reinforced zone) is still not possible since only few punching tests on flat slabs with low and medium amounts of shear reinforcement have been conducted.To investigate the punching shear behavior of flat slabs with a varying amount of shear reinforcement, three systematic test series without and with stirrups as shear reinforcement were conducted. The experimental program included three reference tests without and eight tests with low and medium amounts of shear reinforcement. In the tests, the amount of shear reinforcement was varied by changing the stirrup diameter only. Further investigated influences were the shear span‐depth ratio and the effective depth. The results of the test series are discussed and compared to the predictions according to Eurocode 2, Model Code 2010 and the draft of the second generation of Eurocode 2.
- 15 February 2019
- Published by Wiley in Beton- und Stahlbetonbau
- Vol. 114 (4) , 231-241
Durchstanztragverhalten von Einzelfundamenten mit variierenden Durchstanzbewehrungsgraden
- 15 February 2019
- Published by Wiley in Beton- und Stahlbetonbau
- Vol. 114 (4) , 231-241
Durchstanztragverhalten von Einzelfundamenten mit variierenden Durchstanzbewehrungsgraden
- 1 February 2019
- Published by Elsevier in Engineering Structures
- Vol. 181, 216-232
Two-parameter kinematic theory for punching shear in reinforced concrete slabs with shear reinforcement
- 1 February 2019
- Published by Elsevier in Engineering Structures
- Vol. 181, 216-232
Two-parameter kinematic theory for punching shear in reinforced concrete slabs with shear reinforcement
- 27 December 2018
- Published by Wiley in Structural Concrete
- Vol. 20 (2) , 552-563
Punching shear behavior of reinforced concrete footings with a varying amount of shear reinforcement
The existing punching shear design provisions according to current codes have either a semi‐empirical (e.g., Eurocode 2) or a more physical (e.g., Model Code 2010) background. Although the design procedures are very similar, the predicted punching shear capacities may differ significantly, depending on the background of the design provisions and the considered influences. Recent test series on reinforced concrete footings without shear reinforcement and with high amounts of shear reinforcement are available and can be used for the evaluation and improvement of the current provisions. Nevertheless, the evaluation of the code equations for the design of the shear reinforcement (failure inside the shear‐reinforced zone) is still not possible since systematic test series on footings with a varying amount of shear reinforcement have not yet been conducted. To investigate the punching shear behavior of reinforced concrete footings with low and medium amounts of shear reinforcement, three systematic test series (11 specimens) with stirrups as shear reinforcement were conducted. In the tests, the amount of shear reinforcement was varied by changing the stirrup diameter only. Further investigated influences were the shear span‐depth ratio and the effective depth. In this paper, the results of the test series are discussed and compared to the predictions according to Eurocode 2, Model Code 2010, and the draft of the second generation of Eurocode 2.
- 27 December 2018
- Published by Wiley in Structural Concrete
- Vol. 20 (2) , 552-563
Punching shear behavior of reinforced concrete footings with a varying amount of shear reinforcement
The existing punching shear design provisions according to current codes have either a semi‐empirical (e.g., Eurocode 2) or a more physical (e.g., Model Code 2010) background. Although the design procedures are very similar, the predicted punching shear capacities may differ significantly, depending on the background of the design provisions and the considered influences. Recent test series on reinforced concrete footings without shear reinforcement and with high amounts of shear reinforcement are available and can be used for the evaluation and improvement of the current provisions. Nevertheless, the evaluation of the code equations for the design of the shear reinforcement (failure inside the shear‐reinforced zone) is still not possible since systematic test series on footings with a varying amount of shear reinforcement have not yet been conducted. To investigate the punching shear behavior of reinforced concrete footings with low and medium amounts of shear reinforcement, three systematic test series (11 specimens) with stirrups as shear reinforcement were conducted. In the tests, the amount of shear reinforcement was varied by changing the stirrup diameter only. Further investigated influences were the shear span‐depth ratio and the effective depth. In this paper, the results of the test series are discussed and compared to the predictions according to Eurocode 2, Model Code 2010, and the draft of the second generation of Eurocode 2.
- 1 November 2018
- Published by Elsevier in Engineering Structures
- Vol. 175, 201-216
Two-parameter kinematic theory for punching shear in reinforced concrete slabs without shear reinforcement
- 1 November 2018
- Published by Elsevier in Engineering Structures
- Vol. 175, 201-216
Two-parameter kinematic theory for punching shear in reinforced concrete slabs without shear reinforcement
- 1 September 2018
- Published by Elsevier in Engineering Structures
- Vol. 171, 269-279
Fracture kinematics of reinforced concrete slabs failing in punching
- 1 September 2018
- Published by Elsevier in Engineering Structures
- Vol. 171, 269-279
Fracture kinematics of reinforced concrete slabs failing in punching
- 1 June 2018
- Published by Elsevier in Journal of Constructional Steel Research
- Vol. 145, 232-243
Puzzle-shaped rib shear connectors subjected to combined shear and tension
- 1 June 2018
- Published by Elsevier in Journal of Constructional Steel Research
- Vol. 145, 232-243
Puzzle-shaped rib shear connectors subjected to combined shear and tension