Xuejin Wang
Research Subjects
Xuejin Wang has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
Kun Pan
China Agricultural University
4 shared publications- Jing-Yu Qu
College of Science, China Agricultural University, Beijing, 100083, China
3 shared publications Zheng-Fei Guo
China Agricultural University
3 shared publicationsKai Feng
College of Science, China Agricultural University, Beijing, 100083, China
2 shared publications- Yun Zhao
College of Science, China Agricultural University, Beijing, 100083, China
2 shared publications Zheng Qi
College of Science, China Agricultural University, 17 Qinghua Donglu, Haidian District, Beijing 100083, China
2 shared publications
Latest Publications
- 22 January 2025
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 17 (5) , 2889-2896
Preparation of sandwich-structured V6O13via direct current magnetron sputtering for high-capacity zinc-ion batteries
In this study, sandwich-structured vanadium oxide (V6O13) was prepared and employed as the cathode for zinc-ion batteries (ZIBs). It achieved a specific capacity of 550 mA h g−1 at 100 mA g−1, with a coulombic efficiency maintained at 100%.
- 22 January 2025
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 17 (5) , 2889-2896
Preparation of sandwich-structured V6O13via direct current magnetron sputtering for high-capacity zinc-ion batteries
In this study, sandwich-structured vanadium oxide (V6O13) was prepared and employed as the cathode for zinc-ion batteries (ZIBs). It achieved a specific capacity of 550 mA h g−1 at 100 mA g−1, with a coulombic efficiency maintained at 100%.
- 14 January 2025
- Published by Elsevier in Surfaces and Interfaces
- Vol. 58
Enhanced tribological and antimicrobial performance by sputtered heterojunction of ZnO-TiO2 multilayer thin film
- 14 January 2025
- Published by Elsevier in Surfaces and Interfaces
- Vol. 58
Enhanced tribological and antimicrobial performance by sputtered heterojunction of ZnO-TiO2 multilayer thin film
- 9 October 2024
- Published by Elsevier in Electrochimica Acta
- Vol. 507
High-capacity and fast-charging Al battery based on Cu/KB cathode
- 9 October 2024
- Published by Elsevier in Electrochimica Acta
- Vol. 507
High-capacity and fast-charging Al battery based on Cu/KB cathode
- Open Access
- 16 June 2021
- Published by Taylor & Francis in Immunological Investigations
- Vol. 51 (5) , 1330-1346
Activation of Gonadotropin-releasing Hormone Receptor Impedes the Immunosuppressive Activity of Decidual Regulatory T Cells via Deactivating the Mechanistic Target of Rapamycin Signaling
Understanding maternal immune tolerance is crucial for the development of therapeutics for immunological pregnancy complications. Decidual regulatory T cells (Tregs) play a pivotal role in the maintenance of maternal immune tolerance. Using a murine allogeneic pregnancy model in the current study, we identified the up-regulation of gonadotropin-releasing hormone receptor (GnRHR) in decidual T cell subsets including CD4+ conventional T cells, CD8+ T cells, and CD4+Foxp3+ Tregs. Using a lentivirus-mediated GnRHR overexpression system and a GnRHR agonist, we found that GnRHR activation decreased the expression of Treg functional molecules such as IL10 (IL-10), IL-35 subunit EBI3 (Ebi3), IL2RA (CD25), TNFRSF18 (GITR), ICOS, and Treg master regulator FOXP3. The functional analysis indicated that GnRHR activation impairs the ability of Tregs to inhibit conventional T cell proliferation. We also revealed that GnRHR activation suppressed the mechanistic target of rapamycin (mTOR) signaling in GnRHR-overexpressing splenic Tregs (Wild type C57BL/6 J background) and decidual Tregs. MHY1485, a potent mTOR activator, effectively abolished the effect of the GnRHR agonist and promoted the immunosuppressive capability of Tregs. Furthermore, in an adoptive transfer model, Treg-specific GnRHR knockdown increased Foxp3 expression in decidual Tregs while decreasing the production of IFN-γ and IL-17 in decidual effector CD4+ T cells and reducing the production of IFN-γ in decidual effector CD8+ T cells. Taken together, the present study unveils a novel mechanism by which the immunosuppressive function of decidual Tregs is modulated, and deepens our understanding of maternal immune tolerance.
- 16 June 2021
- Published by Taylor & Francis in Immunological Investigations
- Vol. 51 (5) , 1330-1346
Open AccessActivation of Gonadotropin-releasing Hormone Receptor Impedes the Immunosuppressive Activity of Decidual Regulatory T Cells via Deactivating the Mechanistic Target of Rapamycin Signaling
Understanding maternal immune tolerance is crucial for the development of therapeutics for immunological pregnancy complications. Decidual regulatory T cells (Tregs) play a pivotal role in the maintenance of maternal immune tolerance. Using a murine allogeneic pregnancy model in the current study, we identified the up-regulation of gonadotropin-releasing hormone receptor (GnRHR) in decidual T cell subsets including CD4+ conventional T cells, CD8+ T cells, and CD4+Foxp3+ Tregs. Using a lentivirus-mediated GnRHR overexpression system and a GnRHR agonist, we found that GnRHR activation decreased the expression of Treg functional molecules such as IL10 (IL-10), IL-35 subunit EBI3 (Ebi3), IL2RA (CD25), TNFRSF18 (GITR), ICOS, and Treg master regulator FOXP3. The functional analysis indicated that GnRHR activation impairs the ability of Tregs to inhibit conventional T cell proliferation. We also revealed that GnRHR activation suppressed the mechanistic target of rapamycin (mTOR) signaling in GnRHR-overexpressing splenic Tregs (Wild type C57BL/6 J background) and decidual Tregs. MHY1485, a potent mTOR activator, effectively abolished the effect of the GnRHR agonist and promoted the immunosuppressive capability of Tregs. Furthermore, in an adoptive transfer model, Treg-specific GnRHR knockdown increased Foxp3 expression in decidual Tregs while decreasing the production of IFN-γ and IL-17 in decidual effector CD4+ T cells and reducing the production of IFN-γ in decidual effector CD8+ T cells. Taken together, the present study unveils a novel mechanism by which the immunosuppressive function of decidual Tregs is modulated, and deepens our understanding of maternal immune tolerance.
- 18 May 2018
- Published by Zhejiang University Press in Journal of Zhejiang University-SCIENCE A
- Vol. 19 (5) , 399-408
Influence of annealing conditions on the properties of Cu(In,Ga)Se2 thin films fabricated by electrodeposition
目的 退火条件直接影响着电沉积制备的铜铟镓硒薄膜品质,而薄膜品质决定着最终得到器件的转换效率。本实验在不同退火条件下对薄膜进行处理,得出退火条件对薄膜各项表征指标的影响规律,并根据观察到的规律改善退火工艺,以提高铜铟镓硒薄膜品质。
- 18 May 2018
- Published by Zhejiang University Press in Journal of Zhejiang University-SCIENCE A
- Vol. 19 (5) , 399-408
Influence of annealing conditions on the properties of Cu(In,Ga)Se2 thin films fabricated by electrodeposition
目的 退火条件直接影响着电沉积制备的铜铟镓硒薄膜品质,而薄膜品质决定着最终得到器件的转换效率。本实验在不同退火条件下对薄膜进行处理,得出退火条件对薄膜各项表征指标的影响规律,并根据观察到的规律改善退火工艺,以提高铜铟镓硒薄膜品质。
- 3 August 2017
- Published by Wiley in Rare Metals
- Vol. 36 (9) , 729-736
Cu(In,Ga)Se 2 absorbers prepared by electrodeposition for low‐cost thin‐film solar cells
Reducing the manufacturing cost of solar cells is necessary to their industrial production. Electrodepositing is an effective, non‐vacuum method which is very suitable for cutting the manufacturing cost of thin films as well as developing its large‐scale industrial production. In this study, about 1‐μm‐thick Cu(In,Ga)Se 2 (CIGS) precursors were electrodeposited on Mo/glass substrates in aqueous solution utilizing a three‐electrode potentiostatic system. Triethanolamine was used as complexing agent, and all parameters of electrodeposition were precisely controlled. After that, the electrodeposited precursors were selenized in a Se atmosphere with different heating ramp rates (60 and 600 °C·min −1 ). High‐quality CIGS films were obtained, and their characteristics were investigated by X‐ray fluorescence, scanning electron microscopy, energy‐dispersive spectroscopy, X‐ray diffraction, Raman spectra and near‐infrared–visible (NIR‐Vis) spectra. The results reveal that there are many differences between the properties of the films under different heating rates. Finally, CIGS solar cells were fabricated using a fast and a slow heating rate. The maximum efficiencies achieved for the films selenized at 60 and 600 °C·min −1 are 3.15% and 0.71%, respectively.
- 3 August 2017
- Published by Wiley in Rare Metals
- Vol. 36 (9) , 729-736
Cu(In,Ga)Se 2 absorbers prepared by electrodeposition for low‐cost thin‐film solar cells
Reducing the manufacturing cost of solar cells is necessary to their industrial production. Electrodepositing is an effective, non‐vacuum method which is very suitable for cutting the manufacturing cost of thin films as well as developing its large‐scale industrial production. In this study, about 1‐μm‐thick Cu(In,Ga)Se 2 (CIGS) precursors were electrodeposited on Mo/glass substrates in aqueous solution utilizing a three‐electrode potentiostatic system. Triethanolamine was used as complexing agent, and all parameters of electrodeposition were precisely controlled. After that, the electrodeposited precursors were selenized in a Se atmosphere with different heating ramp rates (60 and 600 °C·min −1 ). High‐quality CIGS films were obtained, and their characteristics were investigated by X‐ray fluorescence, scanning electron microscopy, energy‐dispersive spectroscopy, X‐ray diffraction, Raman spectra and near‐infrared–visible (NIR‐Vis) spectra. The results reveal that there are many differences between the properties of the films under different heating rates. Finally, CIGS solar cells were fabricated using a fast and a slow heating rate. The maximum efficiencies achieved for the films selenized at 60 and 600 °C·min −1 are 3.15% and 0.71%, respectively.
- 1 February 2016
- Published by IOP Publishing in Chinese Physics B
- Vol. 25 (2) , 028201
In-situ characterization of electrochromism based on ITO/PEDOT:PSS towards preparation of high performance device
Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) is usually sandwiched between indium tin oxide (ITO) and a functional polymer in order to improve the performance of the device. However, because of the strong acidic nature of PEDOT:PSS, the instability of ITO/PEDOT:PSS interface is also observed. The mechanism of degradation of the device remains is unclear and needs to be further studied. In this article, we investigate the in-situ electrochromism of PEDOT:PSS to disclose the cause of the degradation. X-ray photoelectron spectroscopy (XPS) was used to characterize the PEDOT:PSS films, as well as the PEDOT:PSS plus polyethylene glycol (PEG) films with and without indium ions. The electrochromic devices (ECD) based on PEDOT:PSS and PEG with and without indium ions are carried out by in-situ micro-Raman and laser reflective measurement (LRM). For comparison, ECD based on PEDOT:PSS and PEG films with LiCl, KCl, NaCl or InCl3 are also investigated by LRM. The results show that PEDOT:PSS is further reduced when negatively biased, and oxidized when positively biased. This could identify that PEDOT:PSS with indium ions from PEDOT:PSS etching ITO will lose dopants when negatively biased. The LRM shows that the device with indium ions has a stronger effect on the reduction property of PEDOT:PSS-PEG film than the device without indium ions. The contrast of the former device is 44%, that of the latter device is about 3%. The LRM also shows that the contrasts of the device based on PEDOT:PSS+PEG with LiCl, KCl, NaCl, InCl3 are 30%, 27%, 15%, and 18%, respectively.
- 1 February 2016
- Published by IOP Publishing in Chinese Physics B
- Vol. 25 (2) , 028201
In-situ characterization of electrochromism based on ITO/PEDOT:PSS towards preparation of high performance device
Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) is usually sandwiched between indium tin oxide (ITO) and a functional polymer in order to improve the performance of the device. However, because of the strong acidic nature of PEDOT:PSS, the instability of ITO/PEDOT:PSS interface is also observed. The mechanism of degradation of the device remains is unclear and needs to be further studied. In this article, we investigate the in-situ electrochromism of PEDOT:PSS to disclose the cause of the degradation. X-ray photoelectron spectroscopy (XPS) was used to characterize the PEDOT:PSS films, as well as the PEDOT:PSS plus polyethylene glycol (PEG) films with and without indium ions. The electrochromic devices (ECD) based on PEDOT:PSS and PEG with and without indium ions are carried out by in-situ micro-Raman and laser reflective measurement (LRM). For comparison, ECD based on PEDOT:PSS and PEG films with LiCl, KCl, NaCl or InCl3 are also investigated by LRM. The results show that PEDOT:PSS is further reduced when negatively biased, and oxidized when positively biased. This could identify that PEDOT:PSS with indium ions from PEDOT:PSS etching ITO will lose dopants when negatively biased. The LRM shows that the device with indium ions has a stronger effect on the reduction property of PEDOT:PSS-PEG film than the device without indium ions. The contrast of the former device is 44%, that of the latter device is about 3%. The LRM also shows that the contrasts of the device based on PEDOT:PSS+PEG with LiCl, KCl, NaCl, InCl3 are 30%, 27%, 15%, and 18%, respectively.
- 31 December 2015
- Published by IOP Publishing in Chinese Physics B
- Vol. 25 (1) , 017801
Electrochromic & magnetic properties of electrode materials for lithium ion batteries
Progress in electrochromic lithium ion batteries (LIBs) is reviewed, highlighting advances and possible research directions. Methods for using the LIB electrode materials' magnetic properties are also described, using several examples. Li4Ti5O12 (LTO) film is discussed as an electrochromic material and insertion compound. The opto-electrical properties of the LTO film have been characterized by electrical measurements and UV–Vis spectra. A prototype bi-functional electrochromic LIB, incorporating LTO as both electrochromic layer and anode, has also been characterized by charge– discharge measurements and UV–Vis transmittance. The results show that the bi-functional electrochromic LIB prototype works well. Magnetic measurement has proven to be a powerful tool to evaluate the quality of electrode materials. We introduce briefly the magnetism of solids in general, and then discuss the magnetic characteristics of layered oxides, spinel oxides, olivine phosphate LiFePO4, and Nasicon-type Li3Fe2(PO4)3. We also discuss what kind of impurities can be detected, which will guide us to fabricate high quality films and high performance devices.
- 31 December 2015
- Published by IOP Publishing in Chinese Physics B
- Vol. 25 (1) , 017801
Electrochromic & magnetic properties of electrode materials for lithium ion batteries
Progress in electrochromic lithium ion batteries (LIBs) is reviewed, highlighting advances and possible research directions. Methods for using the LIB electrode materials' magnetic properties are also described, using several examples. Li4Ti5O12 (LTO) film is discussed as an electrochromic material and insertion compound. The opto-electrical properties of the LTO film have been characterized by electrical measurements and UV–Vis spectra. A prototype bi-functional electrochromic LIB, incorporating LTO as both electrochromic layer and anode, has also been characterized by charge– discharge measurements and UV–Vis transmittance. The results show that the bi-functional electrochromic LIB prototype works well. Magnetic measurement has proven to be a powerful tool to evaluate the quality of electrode materials. We introduce briefly the magnetism of solids in general, and then discuss the magnetic characteristics of layered oxides, spinel oxides, olivine phosphate LiFePO4, and Nasicon-type Li3Fe2(PO4)3. We also discuss what kind of impurities can be detected, which will guide us to fabricate high quality films and high performance devices.
- 1 April 2012
- Vol. 32 (4) , 1094-7
[Comparative study on thin films of cadmium sulfide prepared by chemical bath deposition and radio frequency magnetron sputtering].
Thin films of cadmium sulfide (CdS) were prepared with ammonium chloride, cadmium chloride, potassium hydroxide and thiourea by chemical bath deposition (CBD). For comparison, CdS films were also deposited by radio frequency (RF) magnetron sputtering, using CdS and argon as a target and reactive gas, respectively. The films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and ultraviolet-visible spectroscopy. The results show that the CdS films prepared by the above two methods have (002) orientation, the CdS films deposited by RF magnetron sputtering are more compact and much smoother than those prepared by CBD, and have lager crystalline size of about 20-30 nm. The CdS films prepared by CBD have smaller crystalline size and more defects. The properties of CdS thin films prepared by RF magnetron sputtering are totally superior to those of CdS films by CBD, but the optical transmittance of CdS thin films at short wavelength is an exception. The energy gap of CdS films prepared by the two methods are all in the range of 2.3-2.5 eV.
- 1 April 2012
- Vol. 32 (4) , 1094-7
[Comparative study on thin films of cadmium sulfide prepared by chemical bath deposition and radio frequency magnetron sputtering].
Thin films of cadmium sulfide (CdS) were prepared with ammonium chloride, cadmium chloride, potassium hydroxide and thiourea by chemical bath deposition (CBD). For comparison, CdS films were also deposited by radio frequency (RF) magnetron sputtering, using CdS and argon as a target and reactive gas, respectively. The films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and ultraviolet-visible spectroscopy. The results show that the CdS films prepared by the above two methods have (002) orientation, the CdS films deposited by RF magnetron sputtering are more compact and much smoother than those prepared by CBD, and have lager crystalline size of about 20-30 nm. The CdS films prepared by CBD have smaller crystalline size and more defects. The properties of CdS thin films prepared by RF magnetron sputtering are totally superior to those of CdS films by CBD, but the optical transmittance of CdS thin films at short wavelength is an exception. The energy gap of CdS films prepared by the two methods are all in the range of 2.3-2.5 eV.