Yajin Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yajin Li has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Bingbing Sun
Xi’an Modern Chemistry Research Institute, 710065 Xi’an, China
2 shared publications - Wuxi Xie
Xi’an Modern Chemistry Research Institute, Xi’an 710065, China
2 shared publications - Yunfei Liu
Xi’an Modern Chemistry Research Institute, Xi’an 710065, China
2 shared publications - Yupeng Shen
State Key Laboratory for Mechanical Behavior of Materials, Xi’an Jiaotong University, Xi’an 710049, China
2 shared publications Haitao Huang
Xi'an Modern Chemistry Research Institute Xi'an China
1 shared publicationHaiyang Wang
Xi'an Modern Chemistry Research Institute Xi'an China
1 shared publication
Latest Publications
- Open Access
Evaluation of Effective Crosslinking Density for Pseudo-Semi Interpenetrating Polymer Networks Based on Polyether Glycols Mixture by Dynamic Mechanical Analysis
Pseudo-semi interpenetrating polymer networks (pseudo-semi IPNs) are a special example of topological isomerism in macromolecules, which have attracted significant attention in recent years with a high potential in a variety of engineering applications of polymeric materials. In this article, pseudo-semi IPNs were synthetized by sequential polymerization of thermoplastic polymers (TPEs) in the presence of thermosetting elastomer (TSEs) with contents of 10, 20, 30, 40 and 50 wt.% in a vacuum oven at 60 °C for about 72 h. In addition, this article describes a method for researching the elastic modulus, effective crosslinking density and physical crosslinking density of TSEs and pseudo-semi IPNs. The inherent interactions and entanglements of pseudo-semi IPNs were discussed by analyzing the changes in elastic modulus and effective crosslinking density at different temperatures. The results show that after the TPE was added to the TSE matrix as a plastic-reinforced material, the ductility increased from 89.6% to 491%, the effective crosslinking density was increased by 100% at high temperatures and the strength of the material matrix was significantly improved. Two physical events take place in our pseudo-semi IPNs as result of energy dissipation and polymeric chains mobility.
Open AccessEvaluation of Effective Crosslinking Density for Pseudo-Semi Interpenetrating Polymer Networks Based on Polyether Glycols Mixture by Dynamic Mechanical Analysis
Pseudo-semi interpenetrating polymer networks (pseudo-semi IPNs) are a special example of topological isomerism in macromolecules, which have attracted significant attention in recent years with a high potential in a variety of engineering applications of polymeric materials. In this article, pseudo-semi IPNs were synthetized by sequential polymerization of thermoplastic polymers (TPEs) in the presence of thermosetting elastomer (TSEs) with contents of 10, 20, 30, 40 and 50 wt.% in a vacuum oven at 60 °C for about 72 h. In addition, this article describes a method for researching the elastic modulus, effective crosslinking density and physical crosslinking density of TSEs and pseudo-semi IPNs. The inherent interactions and entanglements of pseudo-semi IPNs were discussed by analyzing the changes in elastic modulus and effective crosslinking density at different temperatures. The results show that after the TPE was added to the TSE matrix as a plastic-reinforced material, the ductility increased from 89.6% to 491%, the effective crosslinking density was increased by 100% at high temperatures and the strength of the material matrix was significantly improved. Two physical events take place in our pseudo-semi IPNs as result of energy dissipation and polymeric chains mobility.
- Open Access
Effect of Mo Content on In-Situ Anisometric Grains Growth and Mechanical Properties of Mo2FeB2-Based Cermets
Mo2FeB2-based cermets have wide applications in fields of wear resistance, corrosion resistance and heat resistance due to their simple preparation process, low-cost raw materials, and prominent mechanical properties. Herein, Mo2FeB2-based cermets with xMo (x = 43.5, 45.5, 47.5, 49.5, wt.%) were prepared by means of the vacuum liquid phase sintering technique. Investigations on the microstructure and mechanical properties of Mo2FeB2-based cermets with Mo addition were performed. Experimental results show that, with Mo content increasing, the average particle size decreases gradually, revealing that the grain coarsening of Mo2FeB2-based cermets is controlled by interface reaction. In addition, Mo2FeB2 grains gradually transform from an elongated shape to a nearly equiaxed shape. The improvement of Mo2FeB2 hard phase on the morphology is mainly due to the inhibition of solution–precipitation reaction by increasing Mo. Furthermore, the relative density of cermets decreases due to the reduced Fe content. When Mo content is 47.5 wt.%, a relatively small grain size of Mo2FeB2 is obtained (about 2.03 μm). Moreover, with the increase in Mo content, hardness and transverse rupture strength (TRS) of Mo2FeB2-based cermets increase firstly and then decrease. Whereas, with increasing Mo content, the fracture toughness deteriorates gradually. When Mo content is 47.5 wt.%, the comprehensive mechanical properties of cermets are the best. The optimal raw material ratio for the preparation of Mo2FeB2-based cermets in this study is determined to be 47.5 wt.% Mo–6.0 wt.% B-Fe.
Open AccessEffect of Mo Content on In-Situ Anisometric Grains Growth and Mechanical Properties of Mo2FeB2-Based Cermets
Mo2FeB2-based cermets have wide applications in fields of wear resistance, corrosion resistance and heat resistance due to their simple preparation process, low-cost raw materials, and prominent mechanical properties. Herein, Mo2FeB2-based cermets with xMo (x = 43.5, 45.5, 47.5, 49.5, wt.%) were prepared by means of the vacuum liquid phase sintering technique. Investigations on the microstructure and mechanical properties of Mo2FeB2-based cermets with Mo addition were performed. Experimental results show that, with Mo content increasing, the average particle size decreases gradually, revealing that the grain coarsening of Mo2FeB2-based cermets is controlled by interface reaction. In addition, Mo2FeB2 grains gradually transform from an elongated shape to a nearly equiaxed shape. The improvement of Mo2FeB2 hard phase on the morphology is mainly due to the inhibition of solution–precipitation reaction by increasing Mo. Furthermore, the relative density of cermets decreases due to the reduced Fe content. When Mo content is 47.5 wt.%, a relatively small grain size of Mo2FeB2 is obtained (about 2.03 μm). Moreover, with the increase in Mo content, hardness and transverse rupture strength (TRS) of Mo2FeB2-based cermets increase firstly and then decrease. Whereas, with increasing Mo content, the fracture toughness deteriorates gradually. When Mo content is 47.5 wt.%, the comprehensive mechanical properties of cermets are the best. The optimal raw material ratio for the preparation of Mo2FeB2-based cermets in this study is determined to be 47.5 wt.% Mo–6.0 wt.% B-Fe.
- Open Access
- 4 September 2020
- Published by Walter de Gruyter GmbH in Zeitschrift für Kristallographie - New Crystal Structures
- Vol. 235 (6) , 1407-1408
The crystal structure of catena-poly[bis-(3,5-dinitro-1,2,4-triazolato-κ2N:O)-(μ2-1,4-bis(1-imidazolyl)benzene-κ2N:N′)copper(II)], C16H10CuN14O8
C16H10CuN14O8, monoclinic, C2/c (no. 15), a = 13.4851(13) Å, b = 12.3808(12) Å, c = 13.2151(13) Å, β = 97.3040(10)°, V = 2188.4(4) Å3, Z = 4, Rgt(F) = 0.0310, wRref(F2) = 0.1127, T = 296(2) K.
- 4 September 2020
- Published by Walter de Gruyter GmbH in Zeitschrift für Kristallographie - New Crystal Structures
- Vol. 235 (6) , 1407-1408
Open AccessThe crystal structure of catena-poly[bis-(3,5-dinitro-1,2,4-triazolato-κ2N:O)-(μ2-1,4-bis(1-imidazolyl)benzene-κ2N:N′)copper(II)], C16H10CuN14O8
C16H10CuN14O8, monoclinic, C2/c (no. 15), a = 13.4851(13) Å, b = 12.3808(12) Å, c = 13.2151(13) Å, β = 97.3040(10)°, V = 2188.4(4) Å3, Z = 4, Rgt(F) = 0.0310, wRref(F2) = 0.1127, T = 296(2) K.
- 4 August 2020
- Published by Wiley in Propellants, Explosives, Pyrotechnics
- Vol. 45 (10) , 1607-1613
Investigation on the Thermal Behavior of Ammonium Dinitramide with Different Copper‐Based Catalysts
A systematic investigation of the effects of different copper catalysts on the thermal behavior for ammonium dinitramide (ADN) was performed. ADN/copper catalyst mixtures were prepared in the ratio of 100/5 by grinding, and all samples were subjected to TG‐DSC studies using thermo‐gravimetric analysis coupled to Fourier Transformed Infrared Spectrometry (TGA‐FTIR) and Mass Spectrometry, which obtained the detailed information of evolved gas products on pyrolysis and oxidative degradations. Four copper‐series catalysts including copper chromate (CuCrO4), copper chromite (Cu2Cr2O5), copper 2,4‐dihydroxybenzoate (β‐Cu) and metal‐organic framework copper (MOF−Cu) were employed to research the appearance morphology and thermal behavior of the samples. TG‐DSC analysis of the decomposition for ADN/catalyst revealed that copper chromite and β‐Cu exhibit higher catalytic activity than copper chromate due to their greater acceleration of thermal decomposition for ADN. Besides, though MOF−Cu slightly promote the thermal decomposition of ADN, the ADN/MOF−Cu system release more heat during exothermic reaction owing to the high energy of MOF−Cu.
- 4 August 2020
- Published by Wiley in Propellants, Explosives, Pyrotechnics
- Vol. 45 (10) , 1607-1613
Investigation on the Thermal Behavior of Ammonium Dinitramide with Different Copper‐Based Catalysts
A systematic investigation of the effects of different copper catalysts on the thermal behavior for ammonium dinitramide (ADN) was performed. ADN/copper catalyst mixtures were prepared in the ratio of 100/5 by grinding, and all samples were subjected to TG‐DSC studies using thermo‐gravimetric analysis coupled to Fourier Transformed Infrared Spectrometry (TGA‐FTIR) and Mass Spectrometry, which obtained the detailed information of evolved gas products on pyrolysis and oxidative degradations. Four copper‐series catalysts including copper chromate (CuCrO4), copper chromite (Cu2Cr2O5), copper 2,4‐dihydroxybenzoate (β‐Cu) and metal‐organic framework copper (MOF−Cu) were employed to research the appearance morphology and thermal behavior of the samples. TG‐DSC analysis of the decomposition for ADN/catalyst revealed that copper chromite and β‐Cu exhibit higher catalytic activity than copper chromate due to their greater acceleration of thermal decomposition for ADN. Besides, though MOF−Cu slightly promote the thermal decomposition of ADN, the ADN/MOF−Cu system release more heat during exothermic reaction owing to the high energy of MOF−Cu.
- 26 January 2016
- Published by Springer Nature in Journal of Molecular Modeling
- Vol. 22 (2) , 1-11
Research on structures, mechanical properties, and mechanical responses of TKX-50 and TKX-50 based PBX with molecular dynamics
To improve the practicality and safety of a novel explosive dihydroxylamm onium 5,5′-bis (tetrazole)-1,1′-diolate (TKX-50), polyvinylidene difluoride (PVDF) and polychlorotrifluoroe-thylene (PCTFE) were respectively added to the TKX-50, forming the polymer-bonded explosives (PBX). Interfacial and mechanical properties of PBX were investigated through molecular dynamics (MD) method, desensitizing mechanisms of fluorine-polymers for TKX-50 were researched by compression and bulk shear simulations. Results show that the binding energies (E bind ) between polymers (PVDF or PCTFE) and TKX-50 surfaces all rank in order of (011) > (100) > (010), shorter interatomic distance and the resulted higher potentials lead to higher E bind on TKX-50/PVDF interfaces than that on PCTFE/TKX-50 interfaces. Compared with TKX-50, the ductility of PBX is improved due to the isotropic mechanical property and flexibility of fluorine-polymers especially the PCTFE. Desensitizing effect of fluorine-polymers for TKX-50 is found under loading condition, which is attributed to the enhanced compressibility and buffer capacity against external pressure in compression, as well as the improved lubricity to reduce the sliding potentials in bulk shear process.
- 26 January 2016
- Published by Springer Nature in Journal of Molecular Modeling
- Vol. 22 (2) , 1-11
Research on structures, mechanical properties, and mechanical responses of TKX-50 and TKX-50 based PBX with molecular dynamics
To improve the practicality and safety of a novel explosive dihydroxylamm onium 5,5′-bis (tetrazole)-1,1′-diolate (TKX-50), polyvinylidene difluoride (PVDF) and polychlorotrifluoroe-thylene (PCTFE) were respectively added to the TKX-50, forming the polymer-bonded explosives (PBX). Interfacial and mechanical properties of PBX were investigated through molecular dynamics (MD) method, desensitizing mechanisms of fluorine-polymers for TKX-50 were researched by compression and bulk shear simulations. Results show that the binding energies (E bind ) between polymers (PVDF or PCTFE) and TKX-50 surfaces all rank in order of (011) > (100) > (010), shorter interatomic distance and the resulted higher potentials lead to higher E bind on TKX-50/PVDF interfaces than that on PCTFE/TKX-50 interfaces. Compared with TKX-50, the ductility of PBX is improved due to the isotropic mechanical property and flexibility of fluorine-polymers especially the PCTFE. Desensitizing effect of fluorine-polymers for TKX-50 is found under loading condition, which is attributed to the enhanced compressibility and buffer capacity against external pressure in compression, as well as the improved lubricity to reduce the sliding potentials in bulk shear process.