Muhammad Moniruzzaman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Muhammad Moniruzzaman has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
Hamayoun Mahmood
4 shared publicationsSuzana Yusup
4 shared publications- Hazizan Md Akil
School of Materials and Mineral Resources Engineering, Universiti Sains Malaysia (USM), Nibong Tebal, Malaysia
2 shared publications Hazizan Md. Akil
1 shared publicationJale Yanik
Department of Chemistry, Faculty of Science, Ege University, Bornova, Turkey
1 shared publicationKemal Volkan Ozdokur
Department of Chemistry, Faculty of Science, Ege University, Bornova, Turkey
1 shared publication
Latest Publications
- Open Access
- 22 February 2017
- Published by IntechOpen
Green Composites from Ionic Liquid-Assisted Processing of Sustainable Resources: A Brief Overview
Green Composites from Ionic Liquid-Assisted Processing of Sustainable Resources: A Brief Overview | InTechOpen, Published on: 2017-02-22. Authors: Hamayoun Mahmood, Muhammad Moniruzzaman, Suzana Yusup, et
- 22 February 2017
- Published by IntechOpen
Open AccessGreen Composites from Ionic Liquid-Assisted Processing of Sustainable Resources: A Brief Overview
Green Composites from Ionic Liquid-Assisted Processing of Sustainable Resources: A Brief Overview | InTechOpen, Published on: 2017-02-22. Authors: Hamayoun Mahmood, Muhammad Moniruzzaman, Suzana Yusup, et
- 20 July 2016
- Published by Wiley in Polymer Composites
- Vol. 39 (6) , 1994-2003
Ionic liquid pretreatment at high solids loading: A clean approach for fabrication of renewable resource based particulate composites
Recently, the concept of high solids loading in ionic liquid (IL) based pretreatment of lignocellulosic biomass has gained numerous attention due to significant economic, environmental, and sustainability benefits. The objective of the present work was to investigate the impact of ILs pretreatment of lignocellulosic oil palm frond (OPF) biomass at high solids loading on the mechanical and thermal properties of the composite panels. The process combines the pretreatment of OPF particles with ILs [bmim][Cl] (1‐butyl‐3‐methylimidazolium chloride) and [emim][OAc] (1‐ethyl‐3‐methylimidazolium acetate) followed by IL recovery by rinsing with acetone‐water mixture prior to mixing of OPF particles with polymer binder to fabricate compression‐molded composite panels. Untreated and treated OPF particles were characterized by scanning electron microscopy, X‐ray diffraction, thermogravimetric analysis, and chemical composition analysis. Further, the effect of ILs pretreatment on kinetics of thermal degradation of biocomposites was evaluated by activation energy approach. Maximal flexural strength, modulus, and strain energy density (SED) of 25 MPa, 1,928 MPa, and 0.48 MJ/m3, respectively, were found for IL [emim][OAc] treated composite. Besides, thermal properties of IL treated composites were also improved. Present study could be a significant step toward practical IL pretreatment strategies for manufacturing of lignocellulosic based composite materials. POLYM. COMPOS., 39:1994–2003, 2018. © 2016 Society of Plastics Engineers
- 20 July 2016
- Published by Wiley in Polymer Composites
- Vol. 39 (6) , 1994-2003
Ionic liquid pretreatment at high solids loading: A clean approach for fabrication of renewable resource based particulate composites
Recently, the concept of high solids loading in ionic liquid (IL) based pretreatment of lignocellulosic biomass has gained numerous attention due to significant economic, environmental, and sustainability benefits. The objective of the present work was to investigate the impact of ILs pretreatment of lignocellulosic oil palm frond (OPF) biomass at high solids loading on the mechanical and thermal properties of the composite panels. The process combines the pretreatment of OPF particles with ILs [bmim][Cl] (1‐butyl‐3‐methylimidazolium chloride) and [emim][OAc] (1‐ethyl‐3‐methylimidazolium acetate) followed by IL recovery by rinsing with acetone‐water mixture prior to mixing of OPF particles with polymer binder to fabricate compression‐molded composite panels. Untreated and treated OPF particles were characterized by scanning electron microscopy, X‐ray diffraction, thermogravimetric analysis, and chemical composition analysis. Further, the effect of ILs pretreatment on kinetics of thermal degradation of biocomposites was evaluated by activation energy approach. Maximal flexural strength, modulus, and strain energy density (SED) of 25 MPa, 1,928 MPa, and 0.48 MJ/m3, respectively, were found for IL [emim][OAc] treated composite. Besides, thermal properties of IL treated composites were also improved. Present study could be a significant step toward practical IL pretreatment strategies for manufacturing of lignocellulosic based composite materials. POLYM. COMPOS., 39:1994–2003, 2018. © 2016 Society of Plastics Engineers
- 17 July 2016
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 38 (14) , 2065-2071
Kinetic modeling and optimization of biomass pyrolysis for bio-oil production
Thermo-kinetic models for biomass pyrolysis were simulated under both isothermal and non-isothermal conditions to predict the optimum parameters for bio-oil production. A comparative study for wood, sewage sludge, and newspaper print pyrolysis was conducted. The models were numerically solved by using the fourth order Runge–Kutta method in Matlab-7. It was also observed that newspaper print acquired least pyrolysis time to attain optimum bio-oil yield followed by wood and sewage sludge under the identical conditions of temperature and heating rate. Thus, at 10 K/min, the optimum pyrolysis time was 21.0, 23.8, and 42.6 min for newspaper print, wood, and sewage sludge, respectively, whereas the maximum bio-oil yield predicted was 68, 52, and 36%, respectively.
- 17 July 2016
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 38 (14) , 2065-2071
Kinetic modeling and optimization of biomass pyrolysis for bio-oil production
Thermo-kinetic models for biomass pyrolysis were simulated under both isothermal and non-isothermal conditions to predict the optimum parameters for bio-oil production. A comparative study for wood, sewage sludge, and newspaper print pyrolysis was conducted. The models were numerically solved by using the fourth order Runge–Kutta method in Matlab-7. It was also observed that newspaper print acquired least pyrolysis time to attain optimum bio-oil yield followed by wood and sewage sludge under the identical conditions of temperature and heating rate. Thus, at 10 K/min, the optimum pyrolysis time was 21.0, 23.8, and 42.6 min for newspaper print, wood, and sewage sludge, respectively, whereas the maximum bio-oil yield predicted was 68, 52, and 36%, respectively.
- 24 June 2016
- Published by Springer Nature in Wood Science and Technology
- Vol. 50 (6) , 1213-1226
Synthesis and characterization of a polyoxometalate-based ionic liquid catalyst for delignification of wood biomass
- 24 June 2016
- Published by Springer Nature in Wood Science and Technology
- Vol. 50 (6) , 1213-1226
Synthesis and characterization of a polyoxometalate-based ionic liquid catalyst for delignification of wood biomass
- 26 February 2016
- Published by Springer Nature in Clean Technologies and Environmental Policy
- Vol. 18 (7) , 2217-2226
Particulate composites based on ionic liquid-treated oil palm fiber and thermoplastic starch adhesive
- 26 February 2016
- Published by Springer Nature in Clean Technologies and Environmental Policy
- Vol. 18 (7) , 2217-2226
Particulate composites based on ionic liquid-treated oil palm fiber and thermoplastic starch adhesive