Pourya Moradihamedani
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Pourya Moradihamedani has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Abdul Halim Abdullah
Department of Chemistry, Faculty of Science, Universiti Putra Malaysia, Serdang, Malaysia
2 shared publications - Katayoon Kalantari
Department of Chemical Engineering, Northeastern University, Boston, MA 02115, USA
2 shared publications Abdul Halim Bin Abdullah
Universiti Putra Malaysia
1 shared publicationAmalina Binti Muhammad Afifi
University of Malaya
1 shared publication- Noor Azian Morad
Shizen Conversion and Separation Technology (Shizen ikohza), Malaysia-Japan International Institute of Technology (MJIIT), University Teknologi Malaysia (UTM) Kuala Lumpur, Jalan Sultan Yahya Petra, 54100 Kuala Lumpur, Malaysia
1 shared publication Nor Azowa Ibrahim
Universiti Putra Malaysia
1 shared publication
Latest Publications
- 18 November 2017
- Published by Springer Nature in Polymer Bulletin
- Vol. 75 (8) , 3723-3738
Polysulfone mixed-matrix membrane incorporating talc clay particles for gas separation
- 18 November 2017
- Published by Springer Nature in Polymer Bulletin
- Vol. 75 (8) , 3723-3738
Polysulfone mixed-matrix membrane incorporating talc clay particles for gas separation
- Open Access
- 20 June 2016
- Published by Elsevier in Desalination and Water Treatment
- Vol. 57 (59) , 28900-28909
High efficient removal of lead(II) and nickel(II) from aqueous solution by novel polysulfone/Fe3O4–talc nanocomposite mixed matrix membrane
Novel mixed matrix membranes were prepared from polysulfone (PSf), talc and Fe3O4–talc nanocomposite by phase inversion technique. PSf/Fe3O4–talc membranes showed higher lead and nickel rejections compared to PSf/talc membranes, which reaches to 99.4 and 96.2% for lead and nickel ions, respectively, at feed pH 5 and lower rejections at pH 3.5 and 2. Higher surface area in Fe3O4–talc nanocomposite than talc could be considered as a main reason of higher heavy metals removal in PSf/Fe3O4–talc membranes. The heavy metals removal enhances with the increase in nanocomposite content from 7 to 9 wt.% because higher numbers of vacant sites in membrane morphology were available for adsorption. Heavy metals rejection reduces in higher nanocomposite concentrations (11 and 13 wt.%) due to the formation of macrovoids in membrane substructure. In addition, a reduction in the metal ion rejection was recognized by enhancement in feed solution concentration and applied pressure. This is caused by difficulty for the remaining vacant sites to be filled with the heavy metal ions because of repulsive forces between the adsorbed solute molecules on the surface and solute in bulk phase. The interactions of lead and nickel ions with nanocomposite placed on the membrane top layer were revealed by the scanning electron microscopy with energy dispersive X-rays.
- 20 June 2016
- Published by Elsevier in Desalination and Water Treatment
- Vol. 57 (59) , 28900-28909
Open AccessHigh efficient removal of lead(II) and nickel(II) from aqueous solution by novel polysulfone/Fe3O4–talc nanocomposite mixed matrix membrane
Novel mixed matrix membranes were prepared from polysulfone (PSf), talc and Fe3O4–talc nanocomposite by phase inversion technique. PSf/Fe3O4–talc membranes showed higher lead and nickel rejections compared to PSf/talc membranes, which reaches to 99.4 and 96.2% for lead and nickel ions, respectively, at feed pH 5 and lower rejections at pH 3.5 and 2. Higher surface area in Fe3O4–talc nanocomposite than talc could be considered as a main reason of higher heavy metals removal in PSf/Fe3O4–talc membranes. The heavy metals removal enhances with the increase in nanocomposite content from 7 to 9 wt.% because higher numbers of vacant sites in membrane morphology were available for adsorption. Heavy metals rejection reduces in higher nanocomposite concentrations (11 and 13 wt.%) due to the formation of macrovoids in membrane substructure. In addition, a reduction in the metal ion rejection was recognized by enhancement in feed solution concentration and applied pressure. This is caused by difficulty for the remaining vacant sites to be filled with the heavy metal ions because of repulsive forces between the adsorbed solute molecules on the surface and solute in bulk phase. The interactions of lead and nickel ions with nanocomposite placed on the membrane top layer were revealed by the scanning electron microscopy with energy dispersive X-rays.
- Open Access
- 19 February 2016
- Published by Elsevier in Desalination and Water Treatment
- Vol. 57 (53) , 25542-25550
Phosphate removal from water by polysulfone ultrafiltration membrane using PVP as a hydrophilic modifier
The phosphate removal from aqueous solution was studied with a dead-end filtration process using ultrafiltration membranes. Polysulfone (PSf) ultrafiltration membranes were prepared by blending PSf with polyvinylpyrrolidone (PVP). The prepared membranes were characterized by water content, contact angle, SEM, EDX, AFM, and FTIR. The hydrophilicity and porosity of membrane improved considerably and water contact angle declined with the incorporation of PVP. While pure PSf membrane did not have any flux, PSf/PVP 3 wt.% (UF2) shows 9.6 L/m2 h permeate flux. The impact of diverse operating parameters, such as PVP concentration, pressure, and pH of the feed solution on the removal of phosphate was examined. A high phosphate removal (93.6%) from aqueous solution was observed for UF2 membrane and 87.2% for UF3 membrane at feed solution pH 2. It was found that the phosphate rejection dropped as the pressure and PVP concentration increased. A reduction in pH of the feed solution gave a higher phosphorus rejection.
- 19 February 2016
- Published by Elsevier in Desalination and Water Treatment
- Vol. 57 (53) , 25542-25550
Open AccessPhosphate removal from water by polysulfone ultrafiltration membrane using PVP as a hydrophilic modifier
The phosphate removal from aqueous solution was studied with a dead-end filtration process using ultrafiltration membranes. Polysulfone (PSf) ultrafiltration membranes were prepared by blending PSf with polyvinylpyrrolidone (PVP). The prepared membranes were characterized by water content, contact angle, SEM, EDX, AFM, and FTIR. The hydrophilicity and porosity of membrane improved considerably and water contact angle declined with the incorporation of PVP. While pure PSf membrane did not have any flux, PSf/PVP 3 wt.% (UF2) shows 9.6 L/m2 h permeate flux. The impact of diverse operating parameters, such as PVP concentration, pressure, and pH of the feed solution on the removal of phosphate was examined. A high phosphate removal (93.6%) from aqueous solution was observed for UF2 membrane and 87.2% for UF3 membrane at feed solution pH 2. It was found that the phosphate rejection dropped as the pressure and PVP concentration increased. A reduction in pH of the feed solution gave a higher phosphorus rejection.