Bo-Yuan Chen
Research Subjects
Bo-Yuan Chen has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
Chia-Sung Chiu
National Nano Device Laboratories, Hsinchu, Taiwan
4 shared publicationsGuo-Wei Huang
National Nano Device Laboratories
4 shared publications- Kun-Ming Chen
National Nano Device Laboratories, Hsinchu, Taiwan
4 shared publications Cheng-Chou Hung
United Microelectronics Corporation, Hsinchu, Taiwan
3 shared publications- Guo-Wei Huang
Cedars-Sinai Medical Center 2 Department of Medicine Los Angeles, CA
3 shared publications Pin Su
Department of Electronics Engineering and Institute of Electronics, National Chiao Tung University , Hsinchu, Taiwan
3 shared publications
Latest Publications
- 24 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 65 (10) , 4225-4231
Analog and RF Characteristics of Power FinFET Transistors With Different Drain-Extension Designs
Analog and RF characteristics of power FinFET transistors with different drain-extension structures are investigated for microwave integrated circuit applications. The power FinFETs were designed based on the drain-extended MOSFET structure and fabricated using a standard low-voltage FinFET process. Three various drain-extension configurations are demonstrated and compared. With the low-doped drain extension, the breakdown voltage of power FinFETs is higher than 6.5 V for all samples. For standard power devices, where the drain extension is performed with narrow fins, a high drain resistance is inevitable, resulting in high on-resistance and poor analog and RF performances. For devices with wide drain-extension fins (wide drain FinFET) or a planar drain extension (hybrid FinFET), lower drain resistances are obtained owing to the larger extension width. Therefore, the on-resistances of the wide drain and hybrid devices are much lower than that of the standard counterpart. Moreover, these devices with modified drain extensions also exhibit better analog and RF behaviors. The cutoff frequency of power FinFETs is boosted from 30 to 53 GHz when the drain extension is changed from narrow fins to a planar layout. These experimental results indicate that RF power FinFETs with good performance would be realized with the modified drain-extension designs.
- 24 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 65 (10) , 4225-4231
Analog and RF Characteristics of Power FinFET Transistors With Different Drain-Extension Designs
Analog and RF characteristics of power FinFET transistors with different drain-extension structures are investigated for microwave integrated circuit applications. The power FinFETs were designed based on the drain-extended MOSFET structure and fabricated using a standard low-voltage FinFET process. Three various drain-extension configurations are demonstrated and compared. With the low-doped drain extension, the breakdown voltage of power FinFETs is higher than 6.5 V for all samples. For standard power devices, where the drain extension is performed with narrow fins, a high drain resistance is inevitable, resulting in high on-resistance and poor analog and RF performances. For devices with wide drain-extension fins (wide drain FinFET) or a planar drain extension (hybrid FinFET), lower drain resistances are obtained owing to the larger extension width. Therefore, the on-resistances of the wide drain and hybrid devices are much lower than that of the standard counterpart. Moreover, these devices with modified drain extensions also exhibit better analog and RF behaviors. The cutoff frequency of power FinFETs is boosted from 30 to 53 GHz when the drain extension is changed from narrow fins to a planar layout. These experimental results indicate that RF power FinFETs with good performance would be realized with the modified drain-extension designs.
- 14 March 2017
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 56 (4S) , 04CR09
RF power FinFET transistors with a wide drain-extended fin
Drain-extended FinFET transistors for RF power applications have been fabricated and is presented in this paper. Power FinFETs with a wide drain extension are proposed to reduce the drain resistance. Compared with conventional drain-extended FinFETs, our proposed new devices exhibit lower on-resistances and better high-frequency performances while keeping a similar breakdown voltage. The enhancements of the on-resistance and peak cutoff frequency are 16 and 56%, respectively, under an optimal drain-extension layout. These experimental results suggest that FinFET transistors with a wide drain extension could be used for RF power applications, increasing the possibility of integrating RF power parts into future FinFET system-on-a-chip technologies.
- 14 March 2017
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 56 (4S) , 04CR09
RF power FinFET transistors with a wide drain-extended fin
Drain-extended FinFET transistors for RF power applications have been fabricated and is presented in this paper. Power FinFETs with a wide drain extension are proposed to reduce the drain resistance. Compared with conventional drain-extended FinFETs, our proposed new devices exhibit lower on-resistances and better high-frequency performances while keeping a similar breakdown voltage. The enhancements of the on-resistance and peak cutoff frequency are 16 and 56%, respectively, under an optimal drain-extension layout. These experimental results suggest that FinFET transistors with a wide drain extension could be used for RF power applications, increasing the possibility of integrating RF power parts into future FinFET system-on-a-chip technologies.
- 1 March 2016
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 55 (4S) , 04ER09
High-frequency performances of superjunction laterally diffused metal–oxide–semiconductor transistors for RF power applications
This paper presents the dc and high-frequency performances of laterally diffused metal–oxide–semiconductor (LDMOS) transistors with superjunction (SJ) structures. The SJ-LDMOS transistors were fabricated using a 0.5-µm CMOS process. By utilizing a modified SJ/RESURF layout (Type I) or a tapered SJ layout (Type II) in our devices, better high-frequency performances and higher breakdown voltages are achieved compared with conventional SJ counterpart, owing to the suppression of the substrate-assisted depletion effect and the reduction of the drain resistance. For Type I device with an optimal SJ layout dimension, the cutoff frequency and the breakdown voltage are 3.7 GHz and 68 V, respectively. For Type II device with a smallest p-pillar width near the drain, they can be enhanced further and reach to 4.9 GHz and 83 V. These experimental results suggest that the SJ-LDMOS can be used in the RF power amplifiers.
- 1 March 2016
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 55 (4S) , 04ER09
High-frequency performances of superjunction laterally diffused metal–oxide–semiconductor transistors for RF power applications
This paper presents the dc and high-frequency performances of laterally diffused metal–oxide–semiconductor (LDMOS) transistors with superjunction (SJ) structures. The SJ-LDMOS transistors were fabricated using a 0.5-µm CMOS process. By utilizing a modified SJ/RESURF layout (Type I) or a tapered SJ layout (Type II) in our devices, better high-frequency performances and higher breakdown voltages are achieved compared with conventional SJ counterpart, owing to the suppression of the substrate-assisted depletion effect and the reduction of the drain resistance. For Type I device with an optimal SJ layout dimension, the cutoff frequency and the breakdown voltage are 3.7 GHz and 68 V, respectively. For Type II device with a smallest p-pillar width near the drain, they can be enhanced further and reach to 4.9 GHz and 83 V. These experimental results suggest that the SJ-LDMOS can be used in the RF power amplifiers.
- 10 February 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 33 (4) , 591-593
Random Telegraph Noise in 1X-nm CMOS Silicide Contacts and a Method to Extract Trap Density
The behavior of random telegraph noise was affected by nickel silicide barrier height engineering in advanced nano-CMOS technologies. Contact resistance fluctuations with magnitude of up to 40% were observed when a Schottky barrier was reduced to 0.2 eV. The large contact resistance instability is attributed to the barrier modification by positive charge trapping and detrapping in a Schottky contact. The prevalence and magnitude of the noise are dependent on the contact area, trap density, trap energy, and the silicide Schottky barrier height. In this letter, we propose a fast method to extract the density of responsible contact traps.
- 10 February 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 33 (4) , 591-593
Random Telegraph Noise in 1X-nm CMOS Silicide Contacts and a Method to Extract Trap Density
The behavior of random telegraph noise was affected by nickel silicide barrier height engineering in advanced nano-CMOS technologies. Contact resistance fluctuations with magnitude of up to 40% were observed when a Schottky barrier was reduced to 0.2 eV. The large contact resistance instability is attributed to the barrier modification by positive charge trapping and detrapping in a Schottky contact. The prevalence and magnitude of the noise are dependent on the contact area, trap density, trap energy, and the silicide Schottky barrier height. In this letter, we propose a fast method to extract the density of responsible contact traps.
- 1 February 2012
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 51 (2) , 02BC12
Investigation of Hot-Carrier Stress Effect on High-Frequency Performance of Laterally Diffused Metal–Oxide–Semiconductor Transistors
The hot-carrier stress effects on the high-frequency performance characteristics of laterally diffused metal–oxide–semiconductor (LDMOS) transistors were investigated. A constant bias channel hot-carrier stress was applied at room temperature. After applying 3 h of hot-carrier stress, the on-resistance and saturation drain current degradations are 18 and 9%, respectively. However, the degradations of the cutoff frequency and maximum oscillation frequency were less than 2% when the devices were biased before the onset of quasi-saturation. In addition, we found that the degradations of high-frequency parameters are not related to the change in transconductance but to the changes in gate capacitances. Finally, S-parameter variations under hot-carrier stress were also examined in this study. The observations of S-parameter variations are important for RF power amplifier design.
- 1 February 2012
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 51 (2) , 02BC12
Investigation of Hot-Carrier Stress Effect on High-Frequency Performance of Laterally Diffused Metal–Oxide–Semiconductor Transistors
The hot-carrier stress effects on the high-frequency performance characteristics of laterally diffused metal–oxide–semiconductor (LDMOS) transistors were investigated. A constant bias channel hot-carrier stress was applied at room temperature. After applying 3 h of hot-carrier stress, the on-resistance and saturation drain current degradations are 18 and 9%, respectively. However, the degradations of the cutoff frequency and maximum oscillation frequency were less than 2% when the devices were biased before the onset of quasi-saturation. In addition, we found that the degradations of high-frequency parameters are not related to the change in transconductance but to the changes in gate capacitances. Finally, S-parameter variations under hot-carrier stress were also examined in this study. The observations of S-parameter variations are important for RF power amplifier design.
- 22 February 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 58 (3) , 895-900
Investigation of High-Frequency Noise Characteristics in Tensile-Strained nMOSFETs
For the first time, the high-frequency noise behavior of tensile-strained n-channel metal-oxide-semiconductor field effect transistors, including their temperature dependency, is experimentally examined. Our experimental results show that with similar saturation voltages, the strained device is found to have larger channel noise than the control device at the same bias point. For given direct-current power consumption, however, due to enhanced transconductance, the strained device has better small signal behaviors (higher ft and fmax) and noise characteristics (smaller NFmin and Rn) than the control device.
- 22 February 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 58 (3) , 895-900
Investigation of High-Frequency Noise Characteristics in Tensile-Strained nMOSFETs
For the first time, the high-frequency noise behavior of tensile-strained n-channel metal-oxide-semiconductor field effect transistors, including their temperature dependency, is experimentally examined. Our experimental results show that with similar saturation voltages, the strained device is found to have larger channel noise than the control device at the same bias point. For given direct-current power consumption, however, due to enhanced transconductance, the strained device has better small signal behaviors (higher ft and fmax) and noise characteristics (smaller NFmin and Rn) than the control device.
- 3 August 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 58 (9) , 2319-2325
Temperature-Dependent RF Small-Signal and Noise Characteristics of SOI Dynamic Threshold Voltage MOSFETs
In this paper, temperature-dependent RF small-signal and noise characteristics of silicon-on-insulator (SOI) dynamic threshold voltage (DT) MOSFETs are experimentally examined. In the low-voltage regime, both the cutoff and maximum oscillation frequencies (ft and fmax) tend to increase with temperature. In addition, the inherent body-related parasitics and the series resistance have much more impact on fmax than ft. Besides, we found that the noise stemmed from the body resistance (Rb) would contribute to the output noise current, and degrade the minimum noise figure (NFmin). Our study may provide insights for RF circuit design using advanced SOI DT MOSFETs.
- 3 August 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 58 (9) , 2319-2325
Temperature-Dependent RF Small-Signal and Noise Characteristics of SOI Dynamic Threshold Voltage MOSFETs
In this paper, temperature-dependent RF small-signal and noise characteristics of silicon-on-insulator (SOI) dynamic threshold voltage (DT) MOSFETs are experimentally examined. In the low-voltage regime, both the cutoff and maximum oscillation frequencies (ft and fmax) tend to increase with temperature. In addition, the inherent body-related parasitics and the series resistance have much more impact on fmax than ft. Besides, we found that the noise stemmed from the body resistance (Rb) would contribute to the output noise current, and degrade the minimum noise figure (NFmin). Our study may provide insights for RF circuit design using advanced SOI DT MOSFETs.
- 8 March 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 58 (4) , 740-746
Comprehensive Noise Characterization and Modeling for 65-nm MOSFETs for Millimeter-Wave Applications
Using an external tuner-based method, this paper demonstrates a complete millimeter-wave noise characterization and modeling up to 60 GHz for 65-nm MOSFETs for the first time. Due to channel length modulation, the channel noise continues to increase and remains the most important noise source in the millimeter-wave band. Our experimental results further show that, with the downscaling of channel length, the gate resistance has more serious impact on the high-frequency noise parameters than the substrate resistance even in the millimeter-wave frequency.
- 8 March 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 58 (4) , 740-746
Comprehensive Noise Characterization and Modeling for 65-nm MOSFETs for Millimeter-Wave Applications
Using an external tuner-based method, this paper demonstrates a complete millimeter-wave noise characterization and modeling up to 60 GHz for 65-nm MOSFETs for the first time. Due to channel length modulation, the channel noise continues to increase and remains the most important noise source in the millimeter-wave band. Our experimental results further show that, with the downscaling of channel length, the gate resistance has more serious impact on the high-frequency noise parameters than the substrate resistance even in the millimeter-wave frequency.