Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


William G. Davids has a total of 29 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Impact of Shear Deformations on the Response of Inflated Drop-Stitch Fabric Panels Subjected to Transverse Loads

    by William G. Davids, Aidan G. McGlone

    In this paper, the impact of shear deformations on the load–deflection response of transversely loaded inflatable panels made from drop-stitch fabric is explored. A nonlinear shear constitutive model was derived from torsion tests and integrated into Timoshenko beam theory to predict deflection components. Four-point bend tests of the same panel are conducted at pressures of 34.5, 68.9, and 103 kPa and for span-to-depth ratios of 7.2, 12.5, and 17.8 to give load–deflection response with varying levels of shear deformation. Analytical, mechanics-based expressions are derived to quantify load–deflection response due to bending and shear, including deflections caused by the drop-stitch yarns. The resulting expressions are shown to predict the measured load–deflection behavior to within 20% at the theoretical wrinkling load while indicating that the midspan deflection caused by shear deformations including the effect of the drop-stitch yarns are 78% of the total panel deflection for the lowest inflation pressure and smallest span-to-depth ratio. An approach to reducing panel shear deformability through the incorporation of braided sidewalls is proposed, and a second panel with this modification is fabricated and tested in four-point bending to experimentally demonstrate effectiveness. For the smallest span-to-depth ratio, shear stiffening reduced panel midspan deflection by 17–22% depending on inflation pressure.

  • Open Access

    Hybridizing Additive Manufacturing with Continuous Fiber Reinforced Thermoplastic Composites

    by Philip Bean, Andrew P. Schanck, Zane Dustin, Jason Stevens, Jacob Clark, Cody Sheltra, William G. Davids, Roberto A. Lopez-Anido

    Large Area Additive Manufacturing (LAAM) enables the rapid production of thermoplastic polymer structures but suffers from significant anisotropy and 3D printability limitations. These limitations often require additional material and time in order to incorporate supporting structures. This research explores the integration of continuous fiber reinforced thermoplastics (CFRTP) with LAAM structures. A series of experimental trials were performed, which demonstrate the feasibility and benefits of CFRTP integration, as it can improve structural strength, lightweighting, and manufacturing flexibility. The findings suggest that CFRTP integration can significantly enhance LAAM by reducing material usage, improving mechanical properties, and expanding design possibilities. While further research is needed to optimize the process for specific applications, this process of Hybrid Advanced Additive Manufacturing (HAAM) presents a promising approach for advancing large-scale additive manufacturing.


  • Open Access

    Continuously Formed Fiber-Reinforced Thermoplastic Composite Rebar for Concrete Reinforcement

    by Jacob C. Clark, William G. Davids, Roberto A. Lopez-Anido, Andrew P. Schanck, Cody A. Sheltra

    Despite the strength and ductility of steel reinforcing bars, their susceptibility to corrosion can limit the long-term durability of reinforced concrete structures. Fiber-reinforced polymer (FRP) reinforcing bars made with a thermosetting matrix offer corrosion resistance but cannot be field-bent, which limits flexibility during construction. FRP reinforcing bars made with fiber-reinforced thermoplastic polymers (FRTP) address this limitation; however, their high processing viscosity presents manufacturing challenges. In this study, the Continuous Forming Machine, a novel pultrusion device that uses pre-consolidated fiber-reinforced thermoplastic tapes as feedstock, is described and used to fabricate 12.7 mm nominal diameter thermoplastic composite rebars. Simple bend tests on FRTP rebar that rely on basic equipment are performed to verify its ability to be field-formed. The manual bending technique demonstrated here is practical and straightforward, although it does result in some fiber misalignment. Subsequently, surface deformations are introduced to the rebar to promote mechanical bonding with concrete, and tensile tests of the bars are conducted to determine their mechanical properties. Finally, flexural tests of simply-supported, 6 m long beams reinforced with FRTP rebar are performed to assess their strength and stiffness as well as the practicality of using FRTP rebar. The beam tests demonstrated the prototype FRTP rebar’s potential for reinforcing concrete beams, and the beam load–deformation response and capacity agree well with predictions developed using conventional structural analysis principles. Overall, the results of the research reported indicate that thermoplastic rebars manufactured via the Continuous Forming Machine are a promising alternative to both steel and conventional thermoset composite rebar. However, both the beam and tension test results indicate that improvements in material properties, especially elastic modulus, are necessary to meet the requirements of current FRP rebar specifications.


  • Bending failure mechanisms and kinematics of micropile threaded connections

    by Sebastian Montoya-Vargas, Aaron Gallant, William G. Davids, Keith Berube


  • Open Access

    Development of a Novel Beam-Based Finite-Element Approach for the Computationally Efficient Prediction of Residual Stresses and Displacements in Large 3D-Printed Polymer Parts

    by Irja B. Hepler, William G. Davids

    Recently, 3D printing of large, structural polymer parts has received increasing interest, especially for the creation of recyclable structural parts and tooling. However, the complexity of large-scale 3D polymeric printing often dictates resource-intensive trial and error processes to achieve acceptable parts. Existing computational models used to assess the impact of fabrication conditions typically treat the 3D-printed part as a continuum, incorporate oversimplified boundary conditions and take hours to days to run, making design space exploration infeasible. The purpose of this study is to create a structural model that is computationally efficient compared with traditional continuum models yet retains sufficient accuracy to enable exploration of the design space and prediction of part residual stresses and deformations. To this end, a beam-based finite element methodology was created where beads are represented as beams, vertical springs represent inter-bead transverse force transfer and multi-point, linear constraints enforce strain compatibility between adjacent beads. To test this framework, the fabrication of a large Polyethylene terephthalate glycol (PETG) wall was simulated. The PETG was modeled as linearly elastic with an experimentally derived temperature-dependent coefficient of thermal expansion and elastic modulus using temperature history imported from an ABAQUS thermal model. The results of the simulation were compared to those from a continuum model with an identical material definition, showing reasonable agreement of stresses and displacements. Further, the beam-based model required an order of magnitude less run time. Subsequently, the beam-based model was extended to allow separation of the part from the printing bed and the inclusion of part self-weight during fabrication to assess the significance of these effects that pose challenges for existing continuum models.


  • Open Access

    Behavior of Inflatable Drop-Stitch Fabric Panels Subjected to Bending and Compression

    by William G. Davids

    In this paper, the mechanics of inflatable drop-stitch panels are investigated, including the impact of large shear deformations, nonlinearity due to wrinkling of the panel skin that occurs under net compressive strain, work done by the confined internal air, and the effect of the drop-stitch yarns on the panel skin stresses. A large deflection finite element (FE) analysis framework is presented that allows for a panel’s stability and post-buckling response to be quantified. The FE code is verified through comparison with available analytical solutions, and the impact of critical response drivers is examined. The FE models are then used to explore the capacity of panel walls when used as part of a shelter subject to realistic wind and snow loads and to assess the dependence of the capacity on the important design parameters of inflation pressure and panel depth. The analyses indicate that while the drop-stitch panel capacity is sensitive to the panel depth and inflation pressure, panels with reasonable cross-sectional dimensions are viable for use in structural applications where they must support significant compression and bending. Future work should focus on increasing the structural efficiency and capacity by increasing the panel shear stiffness and operational inflation pressure.


  • Open Access

    In Situ, Real-Time Temperature Mapping and Thermal FE Simulations of Large-Format 3D Printed PETG/CF Vertical Wall

    by Felipe Robles Poblete, Matthew Ireland, Lucinda Slattery, William G. Davids, Roberto A. Lopez-Anido

    This work focuses on simulating the thermal history of a vertical wall consisting of a thermoplastic composite material, poly(ethylene terephthalate) glycol (PETG) with short carbon fiber reinforcement, manufactured using a Big Area Additive Manufacturing (BAAM) system. The incremental deposition process used in additive manufacturing, which corresponds to the repeated deposition of hot material onto cooler material, contributes to the presence of residual stresses and part warping. The prediction of these mechanisms is dependent on thermal history of the part, and the major motivation of this work was to improve the accuracy of finite element (FE) models used to quantify the thermal history of large-format additively manufactured parts. Thermocouples were placed throughout the part at varying heights to measure temperature as a function of time. The FE model developed found a thermal contact conductance between the printed part and the bed of 10 W/m2K and convection coefficient values that linearly varied from 3 to 15 W/m2K through the wall height when making a temperature comparison with the output from the thermocouples. It is also demonstrated that the FE model with a constant convection coefficient under-predicts model temperature at the beginning of the manufacturing process when compared against the model with a variable convection coefficient. The impact of this difference was seen in the stress values, which were larger for the model with a constant convection coefficient. Finally, a correlation equation was derived which allows the findings to be generalized to other vertical structures manufactured on the BAAM. In summary, this work offers valuable insights on material characterization, real-time thermocouple placement, and FE modeling of large-format additively manufactured parts.