Sergey Vladimirovich Chertovskikh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sergey Vladimirovich Chertovskikh has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
L. Sh. Shuster
Ufa State Aviation Technical University, Ufa, Russia
4 shared publicationsI. I. Emaev
Ufa State Aviation Technical University
3 shared publications- B. Sh. Minasov
Bashkir State Medical University
2 shared publications - Rasul R. Yakupov
Bashkir State Medical University
2 shared publications - Amr Elfizy
1000 Marie-Victorin Blvd., Longueuil, QC J4G1A1, Canada
1 shared publication - Azat R. Bilyalov
Bashkir State Medical University
1 shared publication
Latest Publications
- Open Access
- 15 December 2025
- Published by Ufa University of Science and Technology in Materials. Technologies. Design
- Vol. 7 (3(22)) , 5-20
Optimization of the geometry of a characteristic section of a complex-profile thin-walled blank of the original geometry by modeling and finite element analysis methods
The use of superplastic forming (SPF) technology has a wide range of applications: from complexprofile body parts to multilayer spatial structures manufactured in one molding step. One of the main disadvantages of SPF is the uneven thickness of the parts obtained due to the large elongation of the material, often complicated by the design of the part. The solution to this problem is the use of modeling, which allows you to perform calculations, identify characteristic defects and optimize the workpiece in order to obtain a part with the required geometry. The paper considers issues related to the modeling of the manufacture of parts by diffusion welding (DW) with subsequent SPF and finite element analysis of the “isothermal bending” operation and subsequent SPF of the inlet protective edge of a composite gas turbine engine blade made of VT6 titanium alloy (6Al-4V Grade5). The MSC Marc software package was selected as the software package for modeling. Modeling and finite element analysis of the technological processes of isothermal bending (twisting), diffusion welding and superplastic forming of the inlet protective edge of a composite blade were performed. On the basis of the results of modeling and finite element analysis, in order to prevent violation of the internal geometry of the part in the form of rough deformation of the technological radius, it was proposed to use a round constant cross-section wire with a diameter of 3.1 mm made of stainless steel with an anti-diffusion coating applied to it. The optimal geometry of the internal cavity of the blank package and the parameters of the inserted wire were selected.
- 15 December 2025
- Published by Ufa University of Science and Technology in Materials. Technologies. Design
- Vol. 7 (3(22)) , 5-20
Open AccessOptimization of the geometry of a characteristic section of a complex-profile thin-walled blank of the original geometry by modeling and finite element analysis methods
The use of superplastic forming (SPF) technology has a wide range of applications: from complexprofile body parts to multilayer spatial structures manufactured in one molding step. One of the main disadvantages of SPF is the uneven thickness of the parts obtained due to the large elongation of the material, often complicated by the design of the part. The solution to this problem is the use of modeling, which allows you to perform calculations, identify characteristic defects and optimize the workpiece in order to obtain a part with the required geometry. The paper considers issues related to the modeling of the manufacture of parts by diffusion welding (DW) with subsequent SPF and finite element analysis of the “isothermal bending” operation and subsequent SPF of the inlet protective edge of a composite gas turbine engine blade made of VT6 titanium alloy (6Al-4V Grade5). The MSC Marc software package was selected as the software package for modeling. Modeling and finite element analysis of the technological processes of isothermal bending (twisting), diffusion welding and superplastic forming of the inlet protective edge of a composite blade were performed. On the basis of the results of modeling and finite element analysis, in order to prevent violation of the internal geometry of the part in the form of rough deformation of the technological radius, it was proposed to use a round constant cross-section wire with a diameter of 3.1 mm made of stainless steel with an anti-diffusion coating applied to it. The optimal geometry of the internal cavity of the blank package and the parameters of the inserted wire were selected.
- Open Access
- 12 July 2024
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 548, 05001
Influence of the microstructure of Mg-Ca magnesium alloy with TiO2/ZrO2 nano-oxide ALD coating on the functional properties
The paper presents an analysis of the results of evaluating the effect of microstructure obtained by methods of severe plastic deformation (SPD) - equal-channel angular pressing (ECAP) and high-pressure torsion (HPT) - on the mechanical and operational properties of the Mg-1%Ca alloy. The influence of the ZrO2 nano-oxide coating deposited using the atomic layer deposition (ALD) technology was considered in comparison with the uncoated material under study. At the same time, it was noted that the application of a ZrO2 nano-oxide coating by the ALD method made it possible to increase the mechanical characteristics of the ECAP samples by about 20% (the ultimate strength was 205 MPa after ECAP and 262 MPa for ECAP samples with ALD coating). The lowest values of the adhesive component of the friction coefficient were observed on samples after SPD treatment using the HPT method with an applied ZrO2 nano-oxide coating. However, it was found that both the initial material of the study and after SPD treatment by ECAP, the Mg-1% Ca alloy demonstrates a slightly lower damping ability during the deposition of ZrO2 films.
- 12 July 2024
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 548, 05001
Open AccessInfluence of the microstructure of Mg-Ca magnesium alloy with TiO2/ZrO2 nano-oxide ALD coating on the functional properties
The paper presents an analysis of the results of evaluating the effect of microstructure obtained by methods of severe plastic deformation (SPD) - equal-channel angular pressing (ECAP) and high-pressure torsion (HPT) - on the mechanical and operational properties of the Mg-1%Ca alloy. The influence of the ZrO2 nano-oxide coating deposited using the atomic layer deposition (ALD) technology was considered in comparison with the uncoated material under study. At the same time, it was noted that the application of a ZrO2 nano-oxide coating by the ALD method made it possible to increase the mechanical characteristics of the ECAP samples by about 20% (the ultimate strength was 205 MPa after ECAP and 262 MPa for ECAP samples with ALD coating). The lowest values of the adhesive component of the friction coefficient were observed on samples after SPD treatment using the HPT method with an applied ZrO2 nano-oxide coating. However, it was found that both the initial material of the study and after SPD treatment by ECAP, the Mg-1% Ca alloy demonstrates a slightly lower damping ability during the deposition of ZrO2 films.
- 1 December 2021
- Published by Allerton Press in Journal of Friction and Wear
- Vol. 42 (6) , 466-472
Influence of Cutting Conditions on the Wear Resistance of Tools with a TiB2 Coating during Titanium Alloy Machining
The effect of cutting conditions on the tribotechnical characteristics and wear resistance of cutting tools with and without TiB2 coating during processing
- 1 December 2021
- Published by Allerton Press in Journal of Friction and Wear
- Vol. 42 (6) , 466-472
Influence of Cutting Conditions on the Wear Resistance of Tools with a TiB2 Coating during Titanium Alloy Machining
The effect of cutting conditions on the tribotechnical characteristics and wear resistance of cutting tools with and without TiB2 coating during processing
- 1 September 2018
- Published by Allerton Press in Journal of Friction and Wear
- Vol. 39 (5) , 388-393
Effect of Ozone Oxidation and Modification with a Carbon Framework on the Tribotechnical Characteristics of a Plastic Lubricant
The tribotechnical characteristics of grease oxidized with ozone and modified with a carbon framework (CF) are studied. It is shown that, starting from the temperature of 150°C and up to...
- 1 September 2018
- Published by Allerton Press in Journal of Friction and Wear
- Vol. 39 (5) , 388-393
Effect of Ozone Oxidation and Modification with a Carbon Framework on the Tribotechnical Characteristics of a Plastic Lubricant
The tribotechnical characteristics of grease oxidized with ozone and modified with a carbon framework (CF) are studied. It is shown that, starting from the temperature of 150°C and up to...
- 17 November 2017
- Published by Springer Nature in Biomedical Engineering
- Vol. 51 (4) , 271-274
Studies of the Adhesive Component of Friction in Hip Joint Endoprostheses
- 17 November 2017
- Published by Springer Nature in Biomedical Engineering
- Vol. 51 (4) , 271-274
Studies of the Adhesive Component of Friction in Hip Joint Endoprostheses
- Open Access
Tribological and Wear Performance of Carbide Tools with TiB2 PVD Coating under Varying Machining Conditions of TiAl6V4 Aerospace Alloy
Tribological phenomena and tool wear mechanisms during machining of hard-to-cut TiAl6V4 aerospace alloy have been investigated in detail. Since cutting tool wear is directly affected by tribological phenomena occurring between the surfaces of the workpiece and the cutting tool, the performance of the cutting tool is strongly associated with the conditions of the machining process. The present work shows the effect of different machining conditions on the tribological and wear performance of TiB2-coated cutting tools compared to uncoated carbide tools. FEM modeling of the temperature profile on the friction surface was performed for wet machining conditions under varying cutting parameters. Comprehensive characterization of the TiB2 coated vs. uncoated cutting tool wear performance was made using optical 3D imaging, SEM/EDX and XPS methods respectively. The results obtained were linked to the FEM modeling. The studies carried out show that during machining of the TiAl6V4 alloy, the efficiency of the TiB2 coating application for carbide cutting tools strongly depends on cutting conditions. The TiB2 coating is very efficient under roughing at low speeds (with strong buildup edge formation). In contrast, it shows similar wear performance to the uncoated tool under finishing operations at higher cutting speeds when cratering wear predominates.
Open AccessTribological and Wear Performance of Carbide Tools with TiB2 PVD Coating under Varying Machining Conditions of TiAl6V4 Aerospace Alloy
Tribological phenomena and tool wear mechanisms during machining of hard-to-cut TiAl6V4 aerospace alloy have been investigated in detail. Since cutting tool wear is directly affected by tribological phenomena occurring between the surfaces of the workpiece and the cutting tool, the performance of the cutting tool is strongly associated with the conditions of the machining process. The present work shows the effect of different machining conditions on the tribological and wear performance of TiB2-coated cutting tools compared to uncoated carbide tools. FEM modeling of the temperature profile on the friction surface was performed for wet machining conditions under varying cutting parameters. Comprehensive characterization of the TiB2 coated vs. uncoated cutting tool wear performance was made using optical 3D imaging, SEM/EDX and XPS methods respectively. The results obtained were linked to the FEM modeling. The studies carried out show that during machining of the TiAl6V4 alloy, the efficiency of the TiB2 coating application for carbide cutting tools strongly depends on cutting conditions. The TiB2 coating is very efficient under roughing at low speeds (with strong buildup edge formation). In contrast, it shows similar wear performance to the uncoated tool under finishing operations at higher cutting speeds when cratering wear predominates.
- 1 March 2016
- Published by Allerton Press in Journal of Friction and Wear
- Vol. 37 (2) , 165-169
Wear of friction pairs made of titanium carbide-based metal–ceramic material
- 1 March 2016
- Published by Allerton Press in Journal of Friction and Wear
- Vol. 37 (2) , 165-169
Wear of friction pairs made of titanium carbide-based metal–ceramic material
- 1 January 2016
- Published by Allerton Press in Journal of Friction and Wear
- Vol. 37 (1) , 1-6
Tribological characteristics of hip joint endoprostheses
- 1 January 2016
- Published by Allerton Press in Journal of Friction and Wear
- Vol. 37 (1) , 1-6
Tribological characteristics of hip joint endoprostheses