Bikramjit Sharma
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Bikramjit Sharma has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
Rahul Chhibber
Department of Mechanical Engineering, Indian Institute of Technology, Jodhpur, India
2 shared publicationsBhim Sain Singla
Punjabi University
1 shared publicationManvinder Sharma
Chandigarh Group of Colleges
1 shared publicationRajeev Mehta
Department of Chemical Engineering, Thapar University, Patiala, India
1 shared publication- Rajeev Mehta
Chemical Engineering Department, Thapar Institute of Engineering & Technology, Patiala, India
1 shared publication Sumeet Goyal
Chandigarh Group of Colleges
1 shared publication
Latest Publications
- 23 June 2021
- Published by Springer Nature
- p. 133-146
Design and Analysis of Thin Micro-Mechanical Suspended Dielectric RF-MEMS Switch for 5G and IoT Applications
- 23 June 2021
- Published by Springer Nature
- p. 133-146
Design and Analysis of Thin Micro-Mechanical Suspended Dielectric RF-MEMS Switch for 5G and IoT Applications
- 10 January 2018
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 233 (7) , 1363-1374
Effect of mixing parameters, postcuring, and stoichiometry on mechanical properties of fiber reinforced epoxy–clay nanocomposites
The influence of processing variables was experimentally studied for glass fiber reinforced epoxy–clay nanocomposites manufactured using vacuum-assisted wet layup method. The tensile strength, flexural strength, and interlaminar shear strength of these nanocomposites were significantly influenced by the processing variables including the temperature of resin–clay mixture, speed of homogenization, and ultrasonic probe amplitude during premixing of clay minerals in epoxy. The glass transition temperature of glass fiber reinforced composites increased with incorporation of clay minerals in epoxy. Also, the postcuring of the laminates was carried out at three different temperatures, e.g. 100, 130, and 150 ℃ for 3 h. A decrease in tensile modulus, tensile strength, and flexural strength of nanocomposites postcured at 130 and 150 ℃ was observed. Also, the use of non-stoichiometric epoxy resin and hardener ratios had an adverse effect on mechanical properties of fiber reinforced epoxy–clay nanocomposites. In fiber reinforced composites incorporating clay minerals, a uniform dispersion of clay minerals besides a strong interfacial adhesion between clay minerals and polymer and optimum conditions of curing of matrix is a crucial aspect for improved performance over conventional fiber reinforced composites.
- 10 January 2018
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 233 (7) , 1363-1374
Effect of mixing parameters, postcuring, and stoichiometry on mechanical properties of fiber reinforced epoxy–clay nanocomposites
The influence of processing variables was experimentally studied for glass fiber reinforced epoxy–clay nanocomposites manufactured using vacuum-assisted wet layup method. The tensile strength, flexural strength, and interlaminar shear strength of these nanocomposites were significantly influenced by the processing variables including the temperature of resin–clay mixture, speed of homogenization, and ultrasonic probe amplitude during premixing of clay minerals in epoxy. The glass transition temperature of glass fiber reinforced composites increased with incorporation of clay minerals in epoxy. Also, the postcuring of the laminates was carried out at three different temperatures, e.g. 100, 130, and 150 ℃ for 3 h. A decrease in tensile modulus, tensile strength, and flexural strength of nanocomposites postcured at 130 and 150 ℃ was observed. Also, the use of non-stoichiometric epoxy resin and hardener ratios had an adverse effect on mechanical properties of fiber reinforced epoxy–clay nanocomposites. In fiber reinforced composites incorporating clay minerals, a uniform dispersion of clay minerals besides a strong interfacial adhesion between clay minerals and polymer and optimum conditions of curing of matrix is a crucial aspect for improved performance over conventional fiber reinforced composites.
- 8 March 2016
- Published by Taylor & Francis in Composite Interfaces
- Vol. 23 (7) , 623-640
Effect of surface treatment of nanoclay on the mechanical properties of epoxy/glass fiber/clay nanocomposites
A new method of silane treatment of nanoclays is reported where in the clay is nanodispersed in hydrolyzed silanes. The surface functionalization of Cloisite® 15A nanoclay has been carried out using two different silane coupling agents: 3-aminopropyltriethoxy silane and 3-glycidyloxypropyltrimethoxy silane using varied amounts of silane coupling agents, e.g. 10, 50, 200, and 400 wt% of clay. The surface modification of Cloisite® 15A has been confirmed by Fourier transform infrared spectroscopy. The modified clays were then dispersed in epoxy resin, and glass fiber-reinforced epoxy clay laminates were manufactured using vacuum bagging technique. The fiber-reinforced epoxy clay nanocomposites containing silane modified clays have been characterized using small angle X-ray scattering, transmission electron spectroscopy and differential scanning calorimetry. The results indicate that the silane treatment of nanoclay aided the exfoliation of nanoclay and also led to an increase in mechanical properties. The optimized amount of silane coupling agents was 200 wt%. The nanocomposites containing clay modified in 200 wt% of silanes exhibited an exfoliated morphology, improved tensile strength, flexural modulus, and flexural strength. The improved interfacial bonding between silane modified nanoclays and epoxy matrix was also evident from significant increase in elongation at break.
- 8 March 2016
- Published by Taylor & Francis in Composite Interfaces
- Vol. 23 (7) , 623-640
Effect of surface treatment of nanoclay on the mechanical properties of epoxy/glass fiber/clay nanocomposites
A new method of silane treatment of nanoclays is reported where in the clay is nanodispersed in hydrolyzed silanes. The surface functionalization of Cloisite® 15A nanoclay has been carried out using two different silane coupling agents: 3-aminopropyltriethoxy silane and 3-glycidyloxypropyltrimethoxy silane using varied amounts of silane coupling agents, e.g. 10, 50, 200, and 400 wt% of clay. The surface modification of Cloisite® 15A has been confirmed by Fourier transform infrared spectroscopy. The modified clays were then dispersed in epoxy resin, and glass fiber-reinforced epoxy clay laminates were manufactured using vacuum bagging technique. The fiber-reinforced epoxy clay nanocomposites containing silane modified clays have been characterized using small angle X-ray scattering, transmission electron spectroscopy and differential scanning calorimetry. The results indicate that the silane treatment of nanoclay aided the exfoliation of nanoclay and also led to an increase in mechanical properties. The optimized amount of silane coupling agents was 200 wt%. The nanocomposites containing clay modified in 200 wt% of silanes exhibited an exfoliated morphology, improved tensile strength, flexural modulus, and flexural strength. The improved interfacial bonding between silane modified nanoclays and epoxy matrix was also evident from significant increase in elongation at break.