Pavel Růžička
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Pavel Růžička has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Milan Růžička
Czech Technical University in Prague
3 shared publications - Radek Sedláček
Czech Technical University in Prague
3 shared publications - Zdeněk Padovec
Czech Technical University in Prague
3 shared publications Hynek Chlup
Czech Technical University in Prague, Faculty of Mechanical Engineering, Department of Mechanics, Biomechanics and Mechatronics, Technická 4, Prague, 166 07, Czech Republic
1 shared publication- Laurence Chèze
Univ Lyon, Univ Gustave Eiffel, LBMC UMR_T9406, 43 Bd Du 11 Novembre 1918, F69622, Lyon, France
1 shared publication - Lukas Zach
Laboratory of Biomechanics, Faculty of Mechanical Engineering, Czech Technical University, Prague, Technicka 4, 166 07 Prague Czech Republic
1 shared publication
Latest Publications
- Open Access
- 1 November 2017
- Published by Walter de Gruyter GmbH in Strojnícky časopis - Journal of Mechanical Engineering
- Vol. 67 (2) , 85-90
Analysis of Mechanical Properties of the “Bearing” Part Based on Polished Samples
Presented work describes the use of algorithm for the computation of thermo-elastic properties of randomly reinforced composite which is based on histogram from image analysis done on ITAM, CAS. Three polished samples from “Bearing” part were analyzed. Results are used for verification of the algorithm functionality and primarily for computation of thermo-elastic properties which were compared with each other and used in modified FE analysis.
- 1 November 2017
- Published by Walter de Gruyter GmbH in Strojnícky časopis - Journal of Mechanical Engineering
- Vol. 67 (2) , 85-90
Open AccessAnalysis of Mechanical Properties of the “Bearing” Part Based on Polished Samples
Presented work describes the use of algorithm for the computation of thermo-elastic properties of randomly reinforced composite which is based on histogram from image analysis done on ITAM, CAS. Three polished samples from “Bearing” part were analyzed. Results are used for verification of the algorithm functionality and primarily for computation of thermo-elastic properties which were compared with each other and used in modified FE analysis.
- Open Access
- 1 January 2017
- Published by University of West Bohemia in Applied and Computational Mechanics
- Vol. 11 (2)
Design, analysis and testing of an external fracture fixation device manufactured from composite materials
- 1 January 2017
- Published by University of West Bohemia in Applied and Computational Mechanics
- Vol. 11 (2)
Open AccessDesign, analysis and testing of an external fracture fixation device manufactured from composite materials
- 1 January 2016
- Published by Elsevier in Materials Today: Proceedings
- Vol. 3 (2) , 562-566
Isotropy Verification of the C/PPS Samples Manufactured from Pellets by Image Processing Methods and Experiment
- 1 January 2016
- Published by Elsevier in Materials Today: Proceedings
- Vol. 3 (2) , 562-566
Isotropy Verification of the C/PPS Samples Manufactured from Pellets by Image Processing Methods and Experiment
- 1 August 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 2007 (1094687X) , 4305-4307
Knee Joint Endoprosthesis Loading in Full Extension
This paper deals with a knee joint endoprosthesis finite element analysis. Based on a three dimensional geometric model of a lower extremity, a mechanical axis of the limb was designed. This axis is important for several reasons. Firstly, the endoprosthesis was positioned due to its direction, secondly, boundary conditions was defined on its proximal and distal end and finally, the axis enabled reasonable simplification of the model which led to the time saving analysis while preserving principal features of the model like the natural boundary conditions or knee joint's degrees of freedom . Having this, one leg stance was simulated. Results of the analysis were encouraging for future models. Especially the choice of the mechanical axis was suitable and enabled a better distribution of contact pressures and stress on both femoral and tibial component compared to our former models. Also their magnitudes correspond better the manufacturer's experience and our findings. The stresses did not exceeded 30 MPa for the UHMWPE tibial plateau and 100 MPa for the femoral component. The contact pressures were lower than 40 MPa.
- 1 August 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 2007 (1094687X) , 4305-4307
Knee Joint Endoprosthesis Loading in Full Extension
This paper deals with a knee joint endoprosthesis finite element analysis. Based on a three dimensional geometric model of a lower extremity, a mechanical axis of the limb was designed. This axis is important for several reasons. Firstly, the endoprosthesis was positioned due to its direction, secondly, boundary conditions was defined on its proximal and distal end and finally, the axis enabled reasonable simplification of the model which led to the time saving analysis while preserving principal features of the model like the natural boundary conditions or knee joint's degrees of freedom . Having this, one leg stance was simulated. Results of the analysis were encouraging for future models. Especially the choice of the mechanical axis was suitable and enabled a better distribution of contact pressures and stress on both femoral and tibial component compared to our former models. Also their magnitudes correspond better the manufacturer's experience and our findings. The stresses did not exceeded 30 MPa for the UHMWPE tibial plateau and 100 MPa for the femoral component. The contact pressures were lower than 40 MPa.