Saumyadeep Jana
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Saumyadeep Jana has a total of 60 co-authors. Here are the top co-authors by number of shared publications:
Avik Samanta
Pacific Northwest National Laboratory
3 shared publications- Avik Samanta
Department of Mechanical and Aerospace Engineering, University of South Florida, Tampa, USA
3 shared publications Curt Lavender
Pacific Northwest Natl Lab, Richland, WA 99354 USA
3 shared publicationsGlenn J. Grant
Pacific Northwest Natl Lab, Richland, WA 99352 USA
3 shared publicationsHrishikesh Das
Pacific Northwest Natl Lab, Richland, WA 99352 USA
3 shared publications- Ayoub Soulami
Pacific Northwest National Laboratory
2 shared publications
Latest Publications
- 23 November 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 135 (11-12) , 5455-5471
A comparative analysis of residual stresses from friction stir processing of aluminum cast 380 and wrought 7075 alloy sheets: experimental characterization and modeling
- 23 November 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 135 (11-12) , 5455-5471
A comparative analysis of residual stresses from friction stir processing of aluminum cast 380 and wrought 7075 alloy sheets: experimental characterization and modeling
- 15 October 2024
- Published by Elsevier in Manufacturing Letters
- Vol. 41, 504-512
Friction stir processing: A thermomechanical processing tool for high pressure die cast Al-alloys for vehicle light-weighting
- 15 October 2024
- Published by Elsevier in Manufacturing Letters
- Vol. 41, 504-512
Friction stir processing: A thermomechanical processing tool for high pressure die cast Al-alloys for vehicle light-weighting
- Open Access
Chloride-Induced Stress Corrosion Cracking of Friction Stir-Welded 304L Stainless Steel: Effect of Microstructure and Temperature
Dry storage canisters of used nuclear fuels are fabricated using SUS 304L stainless steel. Chloride-induced stress corrosion cracking (CISCC) is one of the major failure modes of dry storage canisters. The cracked canisters can be repaired by friction stir welding (FSW), a low-heat input ‘solid-phase’ welding process. It is important to evaluate the ClSCC resistance of the friction stir welded material. Stress corrosion cracking (SCC) studies were carried out on mill-annealed base materials and friction stir welded 304L stainless U-bend specimens in 3.5% NaCl + 5 N H2SO4 solution at room temperature and boiling MgCl2 solution at 155 °C. The engineering stress on the outer fiber of the FSW U-bend specimen was ~60% higher than that of the base metal (BM). In spite of the higher stress level of the FSW, both materials (FSW and BM) showed almost similar SCC failure times in the two different test solutions. The SCC occurred in the thermo-mechanically affected zone (TMAZ) of the FSW specimens in the 3.5% NaCl + 5 N H2SO4 solution at room temperature, while the stirred zone (SZ) was relatively crack-free. The failure occurred at the stirred zone when tested in the boiling MgCl2 solution. Hydrogen reduction was the cathodic reaction in the boiling MgCl2 solution, which promoted hydrogen-assisted cracking of the heavily deformed stirred zone. The emergence of the slip step followed by passive film rupture and dissolution of the slip step could be the SCC events in the 3.5% NaCl + 5 N H2SO4 solution at room temperature. However, the slip step height was not sufficient to cause passivity breakdown in the fine-grained SZ. Therefore, the SCC occurred in the partially recrystallized softer TMAZ. Overall, the friction-stirred 304L showed higher tolerance to ClSCC than the 304L base metal.
Open AccessChloride-Induced Stress Corrosion Cracking of Friction Stir-Welded 304L Stainless Steel: Effect of Microstructure and Temperature
Dry storage canisters of used nuclear fuels are fabricated using SUS 304L stainless steel. Chloride-induced stress corrosion cracking (CISCC) is one of the major failure modes of dry storage canisters. The cracked canisters can be repaired by friction stir welding (FSW), a low-heat input ‘solid-phase’ welding process. It is important to evaluate the ClSCC resistance of the friction stir welded material. Stress corrosion cracking (SCC) studies were carried out on mill-annealed base materials and friction stir welded 304L stainless U-bend specimens in 3.5% NaCl + 5 N H2SO4 solution at room temperature and boiling MgCl2 solution at 155 °C. The engineering stress on the outer fiber of the FSW U-bend specimen was ~60% higher than that of the base metal (BM). In spite of the higher stress level of the FSW, both materials (FSW and BM) showed almost similar SCC failure times in the two different test solutions. The SCC occurred in the thermo-mechanically affected zone (TMAZ) of the FSW specimens in the 3.5% NaCl + 5 N H2SO4 solution at room temperature, while the stirred zone (SZ) was relatively crack-free. The failure occurred at the stirred zone when tested in the boiling MgCl2 solution. Hydrogen reduction was the cathodic reaction in the boiling MgCl2 solution, which promoted hydrogen-assisted cracking of the heavily deformed stirred zone. The emergence of the slip step followed by passive film rupture and dissolution of the slip step could be the SCC events in the 3.5% NaCl + 5 N H2SO4 solution at room temperature. However, the slip step height was not sufficient to cause passivity breakdown in the fine-grained SZ. Therefore, the SCC occurred in the partially recrystallized softer TMAZ. Overall, the friction-stirred 304L showed higher tolerance to ClSCC than the 304L base metal.
- 15 March 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 126 (3-4) , 1775-1788
On the Utility of the Thermal-Pseudo Mechanical Model’s Residual Stress Prediction Capability for the Development of Friction Stir Processing
- 15 March 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 126 (3-4) , 1775-1788
On the Utility of the Thermal-Pseudo Mechanical Model’s Residual Stress Prediction Capability for the Development of Friction Stir Processing
- 14 July 2022
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 922
Delayed onset of discontinuous precipitation-based phase transformation in U10Mo alloys doped with Silicon
- 14 July 2022
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 922
Delayed onset of discontinuous precipitation-based phase transformation in U10Mo alloys doped with Silicon
- 26 June 2022
- Published by Springer Nature in Journal of Materials Science
- Vol. 57 (25) , 12055-12063
Amorphization and alloying in Al-Ti system through friction extrusion method
- 26 June 2022
- Published by Springer Nature in Journal of Materials Science
- Vol. 57 (25) , 12055-12063
Amorphization and alloying in Al-Ti system through friction extrusion method
- 1 October 2021
- Published by Elsevier in Corrosion Science
- Vol. 191
Microstructural basis for improved corrosion resistance of laser surface processed AZ31 Mg alloy
- 1 October 2021
- Published by Elsevier in Corrosion Science
- Vol. 191
Microstructural basis for improved corrosion resistance of laser surface processed AZ31 Mg alloy
- Open Access
Microstructural Assessment of a Multiple-Intermetallic-Strengthened Aluminum Alloy Produced from Gas-Atomized Powder by Hot Extrusion and Friction Extrusion
An aluminum (Al) matrix with various transition metal (TM) additions is an effective alloying approach for developing high-specific-strength materials for use at elevated temperatures. Conventional fabrication processes such as casting or fusion-related methods are not capable of producing Al–TM alloys in bulk form. Solid phase processing techniques, such as extrusion, have been shown to maintain the microstructure of Al–TM alloys. In this study, extrusions are fabricated from gas-atomized aluminum powders (≈100–400 µm) that contain 12.4 wt % TM additives and an Al-based matrix reinforced by various Al–Fe–Cr–Ti intermetallic compounds (IMCs). Two different extrusion techniques, conventional hot extrusion and friction extrusion, are compared using fabricating rods. During extrusion, the strengthening IMC phases were extensively refined as a result of severe plastic deformation. Furthermore, the quasicrystal approximant IMC phase (70.4 wt % Al, 20.4 wt % Fe, 8.7 wt % Cr, 0.6 wt % Ti) observed in the powder precursor is replaced by new IMC phases such as Al3.2Fe and Al45Cr7-type IMCs. The Al3Ti-type IMC phase is partially dissolved into the Al matrix during extrusion. The combination of linear and rotational shear in the friction extrusion process caused severe deformation in the powders, which allowed for a higher extrusion ratio, eliminated linear voids, and resulted in higher ductility while maintaining strength comparable to that resulting from hot extrusion. Results from equilibrium thermodynamic calculations show that the strengthening IMC phases are stable at elevated temperatures (up to ≈ 600 °C), thus enhancing the high-temperature strength of the extrudates.
Open AccessMicrostructural Assessment of a Multiple-Intermetallic-Strengthened Aluminum Alloy Produced from Gas-Atomized Powder by Hot Extrusion and Friction Extrusion
An aluminum (Al) matrix with various transition metal (TM) additions is an effective alloying approach for developing high-specific-strength materials for use at elevated temperatures. Conventional fabrication processes such as casting or fusion-related methods are not capable of producing Al–TM alloys in bulk form. Solid phase processing techniques, such as extrusion, have been shown to maintain the microstructure of Al–TM alloys. In this study, extrusions are fabricated from gas-atomized aluminum powders (≈100–400 µm) that contain 12.4 wt % TM additives and an Al-based matrix reinforced by various Al–Fe–Cr–Ti intermetallic compounds (IMCs). Two different extrusion techniques, conventional hot extrusion and friction extrusion, are compared using fabricating rods. During extrusion, the strengthening IMC phases were extensively refined as a result of severe plastic deformation. Furthermore, the quasicrystal approximant IMC phase (70.4 wt % Al, 20.4 wt % Fe, 8.7 wt % Cr, 0.6 wt % Ti) observed in the powder precursor is replaced by new IMC phases such as Al3.2Fe and Al45Cr7-type IMCs. The Al3Ti-type IMC phase is partially dissolved into the Al matrix during extrusion. The combination of linear and rotational shear in the friction extrusion process caused severe deformation in the powders, which allowed for a higher extrusion ratio, eliminated linear voids, and resulted in higher ductility while maintaining strength comparable to that resulting from hot extrusion. Results from equilibrium thermodynamic calculations show that the strengthening IMC phases are stable at elevated temperatures (up to ≈ 600 °C), thus enhancing the high-temperature strength of the extrudates.