Yingcheng Hu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Yingcheng Hu has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
Jia Yao
College of Mechanical Engineering, Jiamusi University, 154007, Jiamusi, China
5 shared publicationsWei Lu
College of Mechanical Engineering, Jiamusi University, 154007, Jiamusi, China
5 shared publicationsBing Xue
Key Laboratory of Bio-based Material Science and Technology of Ministry of Education of China, College of Material Science and Engineering, Northeast Forestry University, Harbin, 150040, China; Heilongjiang Institute of Science and Technology
3 shared publicationsFangchao Cheng
Key Laboratory of Bio-based Material Science and Technology of Ministry of Education of China, College of Material Science and Engineering, Northeast Forestry University, Harbin, China
2 shared publicationsLifen Li
2 shared publicationsBaoyu Liu
1 shared publication
Latest Publications
- Open Access
- 1 January 2021
- Published by Tech Science Press in Journal of Renewable Materials
- Vol. 9 (2) , 219-235
A Bifunctional Br鴑sted Acidic Deep Eutectic Solvent to Dissolve and Catalyze the Depolymerization of Alkali Lignin
Lignin is an abundant renewable macromolecular material in nature, and degradation of lignin to improve its hydroxyl content is the key to its efficient use. Alkali lignin (AL) was treated with Brønsted acidic deep eutectic solvent (DES) based on choline chloride and p-toluenesulfonic acid at mild reaction temperature, the structure of the lignin before and after degradation, as well as the composition of small molecules of lignin were analyzed in order to investigate the chemical structure changes of lignin with DES treatment, and the degradation mechanism of lignin in this acidic DES was elucidated in this work. FTIR and NMR analyses demonstrated the selective cleavage of the lignin ether linkages in the degradation process, which was in line with the increased content of phenolic hydroxyl species. XPS revealed that the O/C atomic ratio of the regenerated lignin was lower than that of the AL sample, revealing that the lignin underwent decarbonylation during the DES treatment. Regenerated lignin with low molecular weight and narrow polydispersity index was obtained, and the average molecular weight (Mw) decreased from 17680 g/mol to 2792 g/mol (130°C, 3 h) according to GPC analysis. The lignin-degraded products were mainly G-type phenolics and ketones, and small number of aldehydes were also generated, the possible degradation pathway of lignin in this acidic DES was proposed.
- 1 January 2021
- Published by Tech Science Press in Journal of Renewable Materials
- Vol. 9 (2) , 219-235
Open AccessA Bifunctional Br鴑sted Acidic Deep Eutectic Solvent to Dissolve and Catalyze the Depolymerization of Alkali Lignin
Lignin is an abundant renewable macromolecular material in nature, and degradation of lignin to improve its hydroxyl content is the key to its efficient use. Alkali lignin (AL) was treated with Brønsted acidic deep eutectic solvent (DES) based on choline chloride and p-toluenesulfonic acid at mild reaction temperature, the structure of the lignin before and after degradation, as well as the composition of small molecules of lignin were analyzed in order to investigate the chemical structure changes of lignin with DES treatment, and the degradation mechanism of lignin in this acidic DES was elucidated in this work. FTIR and NMR analyses demonstrated the selective cleavage of the lignin ether linkages in the degradation process, which was in line with the increased content of phenolic hydroxyl species. XPS revealed that the O/C atomic ratio of the regenerated lignin was lower than that of the AL sample, revealing that the lignin underwent decarbonylation during the DES treatment. Regenerated lignin with low molecular weight and narrow polydispersity index was obtained, and the average molecular weight (Mw) decreased from 17680 g/mol to 2792 g/mol (130°C, 3 h) according to GPC analysis. The lignin-degraded products were mainly G-type phenolics and ketones, and small number of aldehydes were also generated, the possible degradation pathway of lignin in this acidic DES was proposed.
- 29 March 2016
- Published by Springer Nature in Waste and Biomass Valorization
- Vol. 7 (6) , 1447-1458
Novel Particleboard Composites Made from Coir Fiber and Waste Banana Stem Fiber
- 29 March 2016
- Published by Springer Nature in Waste and Biomass Valorization
- Vol. 7 (6) , 1447-1458
Novel Particleboard Composites Made from Coir Fiber and Waste Banana Stem Fiber
- Open Access
- 3 February 2016
- Published by BioResources in BioResources
- Vol. 11 (2) , 4605-4620
Layer-by-layer Deposition of TiO2 Nanoparticles in the Wood Surface and its Superhydrophobic Performance
Layer-by-layer Deposition of TiO2 Nanoparticles in the Wood Surface and its Superhydrophobic Performance
- 3 February 2016
- Published by BioResources in BioResources
- Vol. 11 (2) , 4605-4620
Open AccessLayer-by-layer Deposition of TiO2 Nanoparticles in the Wood Surface and its Superhydrophobic Performance
Layer-by-layer Deposition of TiO2 Nanoparticles in the Wood Surface and its Superhydrophobic Performance
- Open Access
- 3 February 2015
- Published by BioResources in BioResources
- Vol. 10 (2) , 3181-3196
Butyration of Lignosulfonate with Butyric Anhydride in the Presence of Choline Chloride
Butyration of Lignosulfonate with Butyric Anhydride in the Presence of Choline Chloride
- 3 February 2015
- Published by BioResources in BioResources
- Vol. 10 (2) , 3181-3196
Open AccessButyration of Lignosulfonate with Butyric Anhydride in the Presence of Choline Chloride
Butyration of Lignosulfonate with Butyric Anhydride in the Presence of Choline Chloride
- Open Access
- 1 May 2013
- Published by BioResources in BioResources
- Vol. 8 (3) , 3336-3346
Mechanical Properties Evaluation of Coir Toughened Unsaturated Polyester with Different Reinforced Body Forms
Mechanical Properties Evaluation of Coir Toughened Unsaturated Polyester with Different Reinforced Body Forms
- 1 May 2013
- Published by BioResources in BioResources
- Vol. 8 (3) , 3336-3346
Open AccessMechanical Properties Evaluation of Coir Toughened Unsaturated Polyester with Different Reinforced Body Forms
Mechanical Properties Evaluation of Coir Toughened Unsaturated Polyester with Different Reinforced Body Forms
- Open Access
- 31 January 2013
- Published by BioResources in BioResources
- Vol. 8 (2) , 2839-2854
Analysis of Nondestructive Testing for Mechanical Properties of LVL at Different Relative Humidities Based on Fuzzy and Classical Mathematics
Laminated veneer lumber (LVL) panels made from poplar (Populus ussuriensis Kom.) and pine (Pinus sylvestris L. var. mongolica Litven.) veneers were tested for mechanical properties in this work. Four different nondestructive testing (NDT) methods and the static bending test were conducted on the LVL. The NDT methods included the longitudinal vibration method, longitudinal transmission method, and in-plane and out-plane flexural vibration methods. The effects of relative humidity on the modulus of elasticity (MOE) and bending strength (MOR) of LVL with vertical load were investigated. Four relative humidities were tested, namely 40%, 50%, 60%, and 70%. The feasibility of NDT testing on LVL was analyzed by fuzzy and classical mathematics. The results showed that the MOE and MOR of LVL diminished with an increase of relative humidity, and the analysis results of fuzzy neartude and correlation coefficients were same. There was a good linear correlation between NDT results and MOE or MOR of poplar and pine LVL.
- 31 January 2013
- Published by BioResources in BioResources
- Vol. 8 (2) , 2839-2854
Open AccessAnalysis of Nondestructive Testing for Mechanical Properties of LVL at Different Relative Humidities Based on Fuzzy and Classical Mathematics
Laminated veneer lumber (LVL) panels made from poplar (Populus ussuriensis Kom.) and pine (Pinus sylvestris L. var. mongolica Litven.) veneers were tested for mechanical properties in this work. Four different nondestructive testing (NDT) methods and the static bending test were conducted on the LVL. The NDT methods included the longitudinal vibration method, longitudinal transmission method, and in-plane and out-plane flexural vibration methods. The effects of relative humidity on the modulus of elasticity (MOE) and bending strength (MOR) of LVL with vertical load were investigated. Four relative humidities were tested, namely 40%, 50%, 60%, and 70%. The feasibility of NDT testing on LVL was analyzed by fuzzy and classical mathematics. The results showed that the MOE and MOR of LVL diminished with an increase of relative humidity, and the analysis results of fuzzy neartude and correlation coefficients were same. There was a good linear correlation between NDT results and MOE or MOR of poplar and pine LVL.
- Open Access
- 31 January 2013
- Published by BioResources in BioResources
- Vol. 8 (2) , 2681-2695
Analysis of the Microstructure and Mechanical Properties of Laminated Veneer Lumber
Analysis of the Microstructure and Mechanical Properties of Laminated Veneer Lumber
- 31 January 2013
- Published by BioResources in BioResources
- Vol. 8 (2) , 2681-2695
Open AccessAnalysis of the Microstructure and Mechanical Properties of Laminated Veneer Lumber
Analysis of the Microstructure and Mechanical Properties of Laminated Veneer Lumber
- Open Access
- 5 November 2012
- Published by BioResources in BioResources
- Vol. 8 (1) , 1409-1419
Optimization and Simulation Research of Tensile Properties of Wood Lap Joint
The performance of veneer joints is known to affect the quality of laminated veneer lumber (LVL), so experimental research and simulation analysis of the tensile properties of lap joints were performed and reported in this paper. The lap length, specimen thickness, and specimen width were selected as the experimental factors. The maximum tensile load increased with the increase of each factor; the tensile strength increased with the increase of lap length, whereas it decreased with the increase of specimen thickness. Specimen width had significant effect on the maximum tensile load, but had little influence on the tensile strength. A response surface model of tensile strength was obtained using Matlab software, and it was used to predict the tensile properties for lap joints. The results of ANSYS simulation analysis showed that the stress peaks were concentrated in the joint ends; the peak shear stress and peak stripping stress all decreased with the increase of lap length and increased with the increase of specimen thickness; the result was consistent with the experimental results; therefore, the finite element simulation results can be used for the optimized selection of size parameters of joints.
- 5 November 2012
- Published by BioResources in BioResources
- Vol. 8 (1) , 1409-1419
Open AccessOptimization and Simulation Research of Tensile Properties of Wood Lap Joint
The performance of veneer joints is known to affect the quality of laminated veneer lumber (LVL), so experimental research and simulation analysis of the tensile properties of lap joints were performed and reported in this paper. The lap length, specimen thickness, and specimen width were selected as the experimental factors. The maximum tensile load increased with the increase of each factor; the tensile strength increased with the increase of lap length, whereas it decreased with the increase of specimen thickness. Specimen width had significant effect on the maximum tensile load, but had little influence on the tensile strength. A response surface model of tensile strength was obtained using Matlab software, and it was used to predict the tensile properties for lap joints. The results of ANSYS simulation analysis showed that the stress peaks were concentrated in the joint ends; the peak shear stress and peak stripping stress all decreased with the increase of lap length and increased with the increase of specimen thickness; the result was consistent with the experimental results; therefore, the finite element simulation results can be used for the optimized selection of size parameters of joints.
- Open Access
- 6 August 2012
- Published by BioResources in BioResources
- Vol. 7 (4) , 5710-5718
RELIABILITY ANALYSIS OF WOOD-PLASTIC PLANKS BASED ON PREDICTED MODULUS OF RUPTURE
The safety of wood-plastic planks based on predicted modulus of rupture (MOR) is presented in this paper. Three different nondestructive testing (NDT) methods were used as checking tools for dynamic modulus of elasticity (MOE) of wood-plastic planks. The MOR was determined by a three-point bending test. The regression relationship between various dynamic MOE and MOR was evaluated to predict MOR of other identical wood-plastic planks. Furthermore, improved first-order second-moment (FOSM) method was used to analyze reliabilities based on measured and predicted MOR, and evaluate safety of them in service. Results indicated that reliabilities of other identical wood-plastic planks based on predicted and measured MOR were almost the same. The greatest difference between them was 0.01%; therefore, their reliability could be analyzed by predicted MOR.
- 6 August 2012
- Published by BioResources in BioResources
- Vol. 7 (4) , 5710-5718
Open AccessRELIABILITY ANALYSIS OF WOOD-PLASTIC PLANKS BASED ON PREDICTED MODULUS OF RUPTURE
The safety of wood-plastic planks based on predicted modulus of rupture (MOR) is presented in this paper. Three different nondestructive testing (NDT) methods were used as checking tools for dynamic modulus of elasticity (MOE) of wood-plastic planks. The MOR was determined by a three-point bending test. The regression relationship between various dynamic MOE and MOR was evaluated to predict MOR of other identical wood-plastic planks. Furthermore, improved first-order second-moment (FOSM) method was used to analyze reliabilities based on measured and predicted MOR, and evaluate safety of them in service. Results indicated that reliabilities of other identical wood-plastic planks based on predicted and measured MOR were almost the same. The greatest difference between them was 0.01%; therefore, their reliability could be analyzed by predicted MOR.
- Open Access
- 6 August 2012
- Published by BioResources in BioResources
- Vol. 7 (4) , 5391-5400
SIMULATION ANALYSIS AND NONDESTRUCTIVE TESTING OF FLEXURAL PERFORMANCE OF WOOD SINGLE LAP GLUED JOINTS
The effect of joint size on the loading capacity of wood single lap joints was studied with an orthogonal experimental design. The maximum load, modulus of elasticity, and modulus of rupture were the three mechanical indexes used to evaluate wood joint quality. A simulation model of bending tests was established using the finite element method. The stress distributions of the joints were analyzed; the peak stripping stress was reduced with an increase in gluing length and thickness. The increase in the corresponding experimental values of maximum load was in agreement with this conclusion. The joint force for various loading positions was simulated, and the peak stress was lowest at the location with the maximum offset. Therefore, the bending capacity of the wood joints can be improved by changing the loading position. Nondestructive fast Fourier transform (FFT) testing of the bending vibration was used to obtain the dynamic elastic modulus. A significant correlation existed between modulus of elasticity and modulus of rupture. Finite element simulation analysis and nondestructive testing are all effective methods for quality evaluation of wood joints, and they can be applied to the design and testing of wood joints.
- 6 August 2012
- Published by BioResources in BioResources
- Vol. 7 (4) , 5391-5400
Open AccessSIMULATION ANALYSIS AND NONDESTRUCTIVE TESTING OF FLEXURAL PERFORMANCE OF WOOD SINGLE LAP GLUED JOINTS
The effect of joint size on the loading capacity of wood single lap joints was studied with an orthogonal experimental design. The maximum load, modulus of elasticity, and modulus of rupture were the three mechanical indexes used to evaluate wood joint quality. A simulation model of bending tests was established using the finite element method. The stress distributions of the joints were analyzed; the peak stripping stress was reduced with an increase in gluing length and thickness. The increase in the corresponding experimental values of maximum load was in agreement with this conclusion. The joint force for various loading positions was simulated, and the peak stress was lowest at the location with the maximum offset. Therefore, the bending capacity of the wood joints can be improved by changing the loading position. Nondestructive fast Fourier transform (FFT) testing of the bending vibration was used to obtain the dynamic elastic modulus. A significant correlation existed between modulus of elasticity and modulus of rupture. Finite element simulation analysis and nondestructive testing are all effective methods for quality evaluation of wood joints, and they can be applied to the design and testing of wood joints.