Katarzyna Mydłowska
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Katarzyna Mydłowska has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Jerzy Ratajski
Faculty of Mechanical and Power Engineering, Koszalin University of Technology, 75-453 Koszalin, Poland
10 shared publications - Adam Gilewicz
Koszalin University of Technology
7 shared publications - Łukasz Szparaga
Faculty of Mechanical Engineering, Koszalin University of Technology (KUT), Śniadeckich 2, 75-453 Koszalin, Poland
5 shared publications - Piotr Myśliński
Koszalin University of Technology
4 shared publications - Błażej Bałasz
Faculty of Mechanical Engineering and Energy, Koszalin University of Technology, Śniadeckich 2, 75-453 Koszalin, Poland
3 shared publications - Ewa Czerwińska
Department of Biomedical Engineering, Koszalin University of Technology, Śniadeckich 2, 75-453 Koszalin, Poland
2 shared publications
Latest Publications
- 1 October 2024
- Published by Index Copernicus in Journal of Achievements in Materials and Manufacturing Engineering
- Vol. 125 (2)
Mathematical modelling of gas nitriding process of steel using cellular automata
The primary aim of this research was to develop a mathematical and computational model of the nitriding process for steel using CA cellular automata theory, which enables the modelling of spatial hardness distributions and nitrogen concentrations within the material.The proposed mathematical model consists of two interacting cellular automata: one representing the surface layer of the nitride material and the other describing the spatial distribution of nitrogen. The developed algorithm and model based on CA were implemented in the MATLAB environment, enabling more effective and efficient testing of the created model and its further use.The developed computer model enabled, by changing the values of the CA model parameters, which correspond to the nitrogen diffusion coefficient in alloy steel, nitrogen solubility in iron and the enthalpy of formation and decomposition of iron nitrides, to adapt the model to the description of the nitriding process of 1.2343 (WCL) steel. The model was experimentally verified by comparing predicted hardness profiles with those measured after nitriding.The main limitation of the developed model is the size of the material fragment in which the nitriding process is simulated.High compliance of the results of numerical calculations with the results obtained by experimental measurements was obtained, which predestines the potential usage of CA-based models for scientific and practical applications. The model can be used as part of an optimisation procedure for designing hybrid composite layers for tribological applications, comprising a nitride layer and a coating deposited via Physical Vapor Deposition (PVD) techniques.The added value of the developed model of the nitriding process, based on the concept of CA, is the author’s modification of the transition rules (both for cells in the Moore and von Neumann neighbourhood) in the automaton related to the structural and phase transformations in the nitride material.
- 1 October 2024
- Published by Index Copernicus in Journal of Achievements in Materials and Manufacturing Engineering
- Vol. 125 (2)
Mathematical modelling of gas nitriding process of steel using cellular automata
The primary aim of this research was to develop a mathematical and computational model of the nitriding process for steel using CA cellular automata theory, which enables the modelling of spatial hardness distributions and nitrogen concentrations within the material.The proposed mathematical model consists of two interacting cellular automata: one representing the surface layer of the nitride material and the other describing the spatial distribution of nitrogen. The developed algorithm and model based on CA were implemented in the MATLAB environment, enabling more effective and efficient testing of the created model and its further use.The developed computer model enabled, by changing the values of the CA model parameters, which correspond to the nitrogen diffusion coefficient in alloy steel, nitrogen solubility in iron and the enthalpy of formation and decomposition of iron nitrides, to adapt the model to the description of the nitriding process of 1.2343 (WCL) steel. The model was experimentally verified by comparing predicted hardness profiles with those measured after nitriding.The main limitation of the developed model is the size of the material fragment in which the nitriding process is simulated.High compliance of the results of numerical calculations with the results obtained by experimental measurements was obtained, which predestines the potential usage of CA-based models for scientific and practical applications. The model can be used as part of an optimisation procedure for designing hybrid composite layers for tribological applications, comprising a nitride layer and a coating deposited via Physical Vapor Deposition (PVD) techniques.The added value of the developed model of the nitriding process, based on the concept of CA, is the author’s modification of the transition rules (both for cells in the Moore and von Neumann neighbourhood) in the automaton related to the structural and phase transformations in the nitride material.
- 1 August 2024
- Published by Index Copernicus in Journal of Achievements in Materials and Manufacturing Engineering
- Vol. 125 (1)
Investigation of the growth kinetics of Streptococcus mutans bacteria on Zr-C coating surfaces deposited on 316L stainless steel substrates
The conducted research aims to describe the kinetics of Streptococcus mutans bacteria growth on the surface of Zr-C coatings with varying carbon content deposited on 316L medical-grade stainless steel substrates.The coatings were deposited using the MS PVD (Magnetron Sputtering Physical Vapour Deposition) technique at a constant temperature of 400C. Varying carbon contents in the coatings were achieved by changing the flow rate of acetylene during the process. The dynamics of bacteria growth cultivated at 37C were examined on the surface of the coatings for incubation times ranging from 0 to 72 hours. Generalised logistic functions were utilised for the mathematical description of the obtained results.The produced coatings exhibited varying carbon content, determining the structural composition ranging from a mixture of metallic Zr and ZrC through stoichiometric zirconium carbide to nanocrystalline grains of ZrC in an amorphous carbon matrix. The obtained results unequivocally demonstrate that in the case of ZrC coatings, the carbon content influences both the bacterial growth rate during the proliferation phase and the final population of bacteria.In the conducted research on bacterial population dynamics, only a single strain of Streptococcus mutans was considered, and the mathematical description was limited to reaching a pseudo-steady state by the population.The proposed model can successfully be adapted to describe the dynamics of other individual strains of bacteria dwelling on metallic surfaces as well as coatings.The proposed model can serve as a tool for studying, among other things, inflexion points of logistic curves, which are considered as the boundary between the dominance of anabolic and catabolic processes in the bacterial population.
- 1 August 2024
- Published by Index Copernicus in Journal of Achievements in Materials and Manufacturing Engineering
- Vol. 125 (1)
Investigation of the growth kinetics of Streptococcus mutans bacteria on Zr-C coating surfaces deposited on 316L stainless steel substrates
The conducted research aims to describe the kinetics of Streptococcus mutans bacteria growth on the surface of Zr-C coatings with varying carbon content deposited on 316L medical-grade stainless steel substrates.The coatings were deposited using the MS PVD (Magnetron Sputtering Physical Vapour Deposition) technique at a constant temperature of 400C. Varying carbon contents in the coatings were achieved by changing the flow rate of acetylene during the process. The dynamics of bacteria growth cultivated at 37C were examined on the surface of the coatings for incubation times ranging from 0 to 72 hours. Generalised logistic functions were utilised for the mathematical description of the obtained results.The produced coatings exhibited varying carbon content, determining the structural composition ranging from a mixture of metallic Zr and ZrC through stoichiometric zirconium carbide to nanocrystalline grains of ZrC in an amorphous carbon matrix. The obtained results unequivocally demonstrate that in the case of ZrC coatings, the carbon content influences both the bacterial growth rate during the proliferation phase and the final population of bacteria.In the conducted research on bacterial population dynamics, only a single strain of Streptococcus mutans was considered, and the mathematical description was limited to reaching a pseudo-steady state by the population.The proposed model can successfully be adapted to describe the dynamics of other individual strains of bacteria dwelling on metallic surfaces as well as coatings.The proposed model can serve as a tool for studying, among other things, inflexion points of logistic curves, which are considered as the boundary between the dominance of anabolic and catabolic processes in the bacterial population.
- Open Access
The Effect of Ageing on Phase Transformations and Mechanical Behaviour in Ni-Rich NiTi Alloys
In this article, the results of research on a NiTi alloy with a high nickel content (51.7 at.%), produced using the additive technology SLM method and subjected to isothermal ageing after solution annealing, are presented. The study involved the determination of the sequence of phase transformations occurring using differential scanning calorimetry (DSC) and the determination of the temperature range of these transformations. In parallel, the phase composition was determined using the XRD method; the hardness and the Young’s modulus were also determined. The analysis of the DSC results obtained indicates the following characteristic features of the NiTi alloy, which change with ageing time: (1) During cooling (from +150 °C to −50 °C), the type of transformation changes from a one-step transformation after solution annealing to a two-step transformation after the ageing process over 1, 20, and 100 h at 500 °C; (2) during heating (from −50 °C to +150 °C) for all the samples, regardless of the ageing time, only a one-step transformation from martensite M(B19′) to austenite A(B2) is observed; (3) the temperature at which the transformation starts increases with the ageing time; (4) the width of the total temperature range of the transformation M(B19′) → A(B2) during heating changes from large (ΔT = 49.7 °C), after solution annealing, to narrow (ΔT = 19.3 °C and ΔT = 17.9 °C after 20 h and 100 h of ageing); and, most importantly, (5) a comparison with the literature data shows that, irrespective of the composition of the NiTi alloy and the manufacturing technology of the alloy samples (regardless of whether this was traditional or additive technology), a sufficiently long ageing process period leads to the occurrence of the martensite → austenite transformation in the same temperature range.
Open AccessThe Effect of Ageing on Phase Transformations and Mechanical Behaviour in Ni-Rich NiTi Alloys
In this article, the results of research on a NiTi alloy with a high nickel content (51.7 at.%), produced using the additive technology SLM method and subjected to isothermal ageing after solution annealing, are presented. The study involved the determination of the sequence of phase transformations occurring using differential scanning calorimetry (DSC) and the determination of the temperature range of these transformations. In parallel, the phase composition was determined using the XRD method; the hardness and the Young’s modulus were also determined. The analysis of the DSC results obtained indicates the following characteristic features of the NiTi alloy, which change with ageing time: (1) During cooling (from +150 °C to −50 °C), the type of transformation changes from a one-step transformation after solution annealing to a two-step transformation after the ageing process over 1, 20, and 100 h at 500 °C; (2) during heating (from −50 °C to +150 °C) for all the samples, regardless of the ageing time, only a one-step transformation from martensite M(B19′) to austenite A(B2) is observed; (3) the temperature at which the transformation starts increases with the ageing time; (4) the width of the total temperature range of the transformation M(B19′) → A(B2) during heating changes from large (ΔT = 49.7 °C), after solution annealing, to narrow (ΔT = 19.3 °C and ΔT = 17.9 °C after 20 h and 100 h of ageing); and, most importantly, (5) a comparison with the literature data shows that, irrespective of the composition of the NiTi alloy and the manufacturing technology of the alloy samples (regardless of whether this was traditional or additive technology), a sufficiently long ageing process period leads to the occurrence of the martensite → austenite transformation in the same temperature range.
- Open Access
- 17 April 2024
- Published by MDPI AG in Preprints.org
The Effect of Ageing on Phase Transformations and Nanoindentation Behaviour in Ni-Rich NiTi Alloys
In the article, the results of research on a NiTi alloy with a high nickel content (51.7 at.%), produced using the additive technology SLM method and subjected to isothermal aging after so-lution annealing, are presented. The study involved the determination of the sequence of phase transformations occurring using differential scanning calorimetry (DSC), and the determination of the temperature range of these transformations. In parallel, the phase composition was determined using the XRD method; hardness and the Young’s modulus were also determined. The analysis of the DSC results obtained indicates the following characteristic features of the NiTi alloy, which change with ageing time: (1) during cooling (from +1500C to -500C), the type of transformation changes from a one-step transformation after solution annealing to a two-step transformation after the ageing process over 1, 20 and 100 hours at 500°C; (2) during heating (from -500C to +1500C) for all the samples, regardless of the ageing time, only a one-step transformation from martensite M(B19’) to austenite A(B2) is observed; (3) the temperature at which the transformation starts increases with the ageing time, (4) the width of the total temperature range of the transformation M(B19’) A(B2) during heating changes from large (∆T=49,7°C), after solution annealing, to narrow (∆T=19.3°C and ∆T=17.9°C after 20 h and 100 h of ageing) and, most importantly, (5) a comparison with literature data shows that, irrespective of the composition of the NiTi alloy and the manufacturing technology of the alloy samples (regardless of the fact whether this was traditional or additive technology), a sufficiently long ageing process period leads to the occurrence of the martensite austenite transformation in the same temperature range.
- 17 April 2024
- Published by MDPI AG in Preprints.org
Open AccessThe Effect of Ageing on Phase Transformations and Nanoindentation Behaviour in Ni-Rich NiTi Alloys
In the article, the results of research on a NiTi alloy with a high nickel content (51.7 at.%), produced using the additive technology SLM method and subjected to isothermal aging after so-lution annealing, are presented. The study involved the determination of the sequence of phase transformations occurring using differential scanning calorimetry (DSC), and the determination of the temperature range of these transformations. In parallel, the phase composition was determined using the XRD method; hardness and the Young’s modulus were also determined. The analysis of the DSC results obtained indicates the following characteristic features of the NiTi alloy, which change with ageing time: (1) during cooling (from +1500C to -500C), the type of transformation changes from a one-step transformation after solution annealing to a two-step transformation after the ageing process over 1, 20 and 100 hours at 500°C; (2) during heating (from -500C to +1500C) for all the samples, regardless of the ageing time, only a one-step transformation from martensite M(B19’) to austenite A(B2) is observed; (3) the temperature at which the transformation starts increases with the ageing time, (4) the width of the total temperature range of the transformation M(B19’) A(B2) during heating changes from large (∆T=49,7°C), after solution annealing, to narrow (∆T=19.3°C and ∆T=17.9°C after 20 h and 100 h of ageing) and, most importantly, (5) a comparison with literature data shows that, irrespective of the composition of the NiTi alloy and the manufacturing technology of the alloy samples (regardless of the fact whether this was traditional or additive technology), a sufficiently long ageing process period leads to the occurrence of the martensite austenite transformation in the same temperature range.
- Open Access
The Influence of Diamond Nanoparticles on Fibroblast Cell Line L929, Cytotoxicity and Bacteriostaticity of Selected Pathogens
The main problem with using modified allotrophic forms of carbon with nanodiamond particles in the production of food packaging is establishing the boundary between safety, as it affects the human body, and the adequate and effective action of the substances. One vital area of concern is the transmission of pathogens in food into the body. The aim of this study was to evaluate the cytotoxicity and bacteriostatic biological activity of two different modifications of diamond nanoparticles: pure detonation nanodiamond particles (DND) obtained by Danienko and plasma-chemically modified detonation nanodiamond particles obtained by the microwave plasma activated chemical vapor deposition method in a rotary chamber (MDP1) An indirect method was used to evaluate the cytotoxicity effect in accordance with ISO 10993–5. The viability of the L929 fibroblast cell line used as a control was 98.5%, for DND 95.14%, and the lowest level of viability for MDP1 was 88.63%. Escherichia coli and Staphylococcus aureus bacteria were used in bacteriostatic tests and the degree of cytotoxicity of the tested materials was classified as low. The in vitro cytotoxicity results indicate no toxic effect on L929 cells nor any effect on any of the samples tested against the bacterial strains us
Open AccessThe Influence of Diamond Nanoparticles on Fibroblast Cell Line L929, Cytotoxicity and Bacteriostaticity of Selected Pathogens
The main problem with using modified allotrophic forms of carbon with nanodiamond particles in the production of food packaging is establishing the boundary between safety, as it affects the human body, and the adequate and effective action of the substances. One vital area of concern is the transmission of pathogens in food into the body. The aim of this study was to evaluate the cytotoxicity and bacteriostatic biological activity of two different modifications of diamond nanoparticles: pure detonation nanodiamond particles (DND) obtained by Danienko and plasma-chemically modified detonation nanodiamond particles obtained by the microwave plasma activated chemical vapor deposition method in a rotary chamber (MDP1) An indirect method was used to evaluate the cytotoxicity effect in accordance with ISO 10993–5. The viability of the L929 fibroblast cell line used as a control was 98.5%, for DND 95.14%, and the lowest level of viability for MDP1 was 88.63%. Escherichia coli and Staphylococcus aureus bacteria were used in bacteriostatic tests and the degree of cytotoxicity of the tested materials was classified as low. The in vitro cytotoxicity results indicate no toxic effect on L929 cells nor any effect on any of the samples tested against the bacterial strains us
- Open Access
Optimisation of Mechanical Properties of Gradient Zr–C Coatings
One of the key components of the designing procedure of a structure of hard anti-wear coatings deposited via Physical Vapour Deposition (PVD) is the analysis of the stress and strain distributions in the substrate/coating systems, initiated during the deposition process and by external mechanical loads. Knowledge of residual stress development is crucial due to their significant influence on the mechanical and tribological properties of such layer systems. The main goal of the work is to find the optimal functionally graded material (FGM) coating’s structure, composed of three functional layers: (1) adhesive layer, providing high adhesion of the coating to the substrate, (2) gradient load support and crack deflection layer, improving hardness and enhancing fracture toughness, (3) wear-resistant top layer, reducing wear. In the optimisation procedure of the coating’s structure, seven decision criteria basing on the state of residual stresses and strains in the substrate/coating system were proposed. Using finite element simulations and postulated criteria, the thickness and composition gradients of the transition layer in FGM coating were determined. In order to verify the proposed optimisation procedure, Zr-C coatings with different spatial distribution of carbon concentration were produced by the Reactive Magnetron Sputtering PVD (RMS PVD) method and their anti-wear properties were assessed by scratch test and ball-on-disc tribological test.
Open AccessOptimisation of Mechanical Properties of Gradient Zr–C Coatings
One of the key components of the designing procedure of a structure of hard anti-wear coatings deposited via Physical Vapour Deposition (PVD) is the analysis of the stress and strain distributions in the substrate/coating systems, initiated during the deposition process and by external mechanical loads. Knowledge of residual stress development is crucial due to their significant influence on the mechanical and tribological properties of such layer systems. The main goal of the work is to find the optimal functionally graded material (FGM) coating’s structure, composed of three functional layers: (1) adhesive layer, providing high adhesion of the coating to the substrate, (2) gradient load support and crack deflection layer, improving hardness and enhancing fracture toughness, (3) wear-resistant top layer, reducing wear. In the optimisation procedure of the coating’s structure, seven decision criteria basing on the state of residual stresses and strains in the substrate/coating system were proposed. Using finite element simulations and postulated criteria, the thickness and composition gradients of the transition layer in FGM coating were determined. In order to verify the proposed optimisation procedure, Zr-C coatings with different spatial distribution of carbon concentration were produced by the Reactive Magnetron Sputtering PVD (RMS PVD) method and their anti-wear properties were assessed by scratch test and ball-on-disc tribological test.
- Open Access
Inter-Relationship between Coating Micro/Nanostructure and the Tribological Performance of Zr–C Gradient Coatings
The research presented in this article concerns Zr–C gradient coatings that were deposited on HS6-5-2 steel by reactive magnetron sputtering from the Zr target in appropriately programmed C2H2 mass flow rate, resulting in various profiles of atomic carbon concentrations in the coating and consequently in spatial change of the properties (H, E, …) and behavior (H/E, H3/E2, We). In particular, the characteristic changes in hardness and Young’s modulus in the Zr–C coatings represented approximately by the bell curve, which has a maximum at the content of about 50 at.% C, were an inspiration to study the behavior of gradient coatings with carbon content in the range of 0–50 and 50–85 at.% with the same hardness change profile. The obtained results indicate that, firstly, the gradient of spatial changes in the coating composition increases their resistance to cohesive damage in comparison to non-gradient coatings, and, secondly, the results show that high hardness is a desired property but not sufficient to ensure adequate coating performance. Independently, an appropriate nano/microstructural structure is necessary, which determines their tribological behavior. In particular, in the case of the tested Zr–C coatings, the obtained results indicate that gradient coatings with a carbon content in the range of 50–85 at.% have better properties, characterized by the critical force Lc2, wear, coefficient of friction, H/E and H3/E2 ratios.
Open AccessInter-Relationship between Coating Micro/Nanostructure and the Tribological Performance of Zr–C Gradient Coatings
The research presented in this article concerns Zr–C gradient coatings that were deposited on HS6-5-2 steel by reactive magnetron sputtering from the Zr target in appropriately programmed C2H2 mass flow rate, resulting in various profiles of atomic carbon concentrations in the coating and consequently in spatial change of the properties (H, E, …) and behavior (H/E, H3/E2, We). In particular, the characteristic changes in hardness and Young’s modulus in the Zr–C coatings represented approximately by the bell curve, which has a maximum at the content of about 50 at.% C, were an inspiration to study the behavior of gradient coatings with carbon content in the range of 0–50 and 50–85 at.% with the same hardness change profile. The obtained results indicate that, firstly, the gradient of spatial changes in the coating composition increases their resistance to cohesive damage in comparison to non-gradient coatings, and, secondly, the results show that high hardness is a desired property but not sufficient to ensure adequate coating performance. Independently, an appropriate nano/microstructural structure is necessary, which determines their tribological behavior. In particular, in the case of the tested Zr–C coatings, the obtained results indicate that gradient coatings with a carbon content in the range of 50–85 at.% have better properties, characterized by the critical force Lc2, wear, coefficient of friction, H/E and H3/E2 ratios.
- Open Access
Evolution of Phase Composition and Antibacterial Activity of Zr–C Thin Films
The research presented in this article concerns Zr–C coatings which were deposited on 304L steel by reactive magnetron sputtering from the Zr target in an Ar–C2H2 atmosphere at various acetylene flow rates, resulting in various atomic carbon concentrations in the coating. The article describes research covering the change in the antibacterial and anticorrosive properties of these coatings due to the change in their chemical and phase composition. The concentration of C in the coatings varied from 21 to 79 at.%. The coating morphology and the elemental distribution in individual coatings were characterized using field emission scanning electron microscopy with an energy-dispersive X-ray analytical system. X-ray diffraction and Raman spectroscopy were used to analyze their microstructure and phase composition. Parallel changes in the mechanical properties of the coatings were analyzed. Based on the obtained results, it was concluded that the wide possibility of shaping the mechanical properties of Zr–C coatings in combination with relatively good antibacterial properties after exceeding 50 at.% of carbon concentration in coatings and high protective potential of these coatings make them a good candidate for medical applications. In particular, corrosion tests showed the high anti-pitting potential of Zr–C coatings in the environment of artificial saliva.
Open AccessEvolution of Phase Composition and Antibacterial Activity of Zr–C Thin Films
The research presented in this article concerns Zr–C coatings which were deposited on 304L steel by reactive magnetron sputtering from the Zr target in an Ar–C2H2 atmosphere at various acetylene flow rates, resulting in various atomic carbon concentrations in the coating. The article describes research covering the change in the antibacterial and anticorrosive properties of these coatings due to the change in their chemical and phase composition. The concentration of C in the coatings varied from 21 to 79 at.%. The coating morphology and the elemental distribution in individual coatings were characterized using field emission scanning electron microscopy with an energy-dispersive X-ray analytical system. X-ray diffraction and Raman spectroscopy were used to analyze their microstructure and phase composition. Parallel changes in the mechanical properties of the coatings were analyzed. Based on the obtained results, it was concluded that the wide possibility of shaping the mechanical properties of Zr–C coatings in combination with relatively good antibacterial properties after exceeding 50 at.% of carbon concentration in coatings and high protective potential of these coatings make them a good candidate for medical applications. In particular, corrosion tests showed the high anti-pitting potential of Zr–C coatings in the environment of artificial saliva.
- Open Access
- 1 June 2017
- Published by Walter de Gruyter GmbH in Archives of Metallurgy and Materials
- Vol. 62 (2) , 771-776
Analysis of Thermal Stability of CrCN Coatings Deposited on Nitrided Substrates Using Modulated Temperature Thermodilatometry
The aim of the research was to investigate the influence of nitriding of the substrate made of 42CrMo4 steel on thermal stability of the antiwear CrCN coating deposited on its surface using Cathodic Arc Evaporation method. Samples of non-nitrided and nitrided substrate/CrCN coating systems were tested with Modulated Temperature Thermodilatometry, which program included system annealing in 26 h, temperature of 290°C and argon atmosphere. Recorded during tests, changes in substrate elongation in response for changes of sample temperature, enabled qualitative determination of changes in stress states in the coatings as a result of samples annealing. Annealing of the system with nitrided substrate resulted in smaller change in residual stress in coating than for the system with non-nitrided substrate, which can indicate its better thermal stability. Values of residual stresses in coatings calculated by sin2ψ method before and after annealing on the basis of tests performed using X-Ray diffraction, agree with results of dilatometric tests.
- 1 June 2017
- Published by Walter de Gruyter GmbH in Archives of Metallurgy and Materials
- Vol. 62 (2) , 771-776
Open AccessAnalysis of Thermal Stability of CrCN Coatings Deposited on Nitrided Substrates Using Modulated Temperature Thermodilatometry
The aim of the research was to investigate the influence of nitriding of the substrate made of 42CrMo4 steel on thermal stability of the antiwear CrCN coating deposited on its surface using Cathodic Arc Evaporation method. Samples of non-nitrided and nitrided substrate/CrCN coating systems were tested with Modulated Temperature Thermodilatometry, which program included system annealing in 26 h, temperature of 290°C and argon atmosphere. Recorded during tests, changes in substrate elongation in response for changes of sample temperature, enabled qualitative determination of changes in stress states in the coatings as a result of samples annealing. Annealing of the system with nitrided substrate resulted in smaller change in residual stress in coating than for the system with non-nitrided substrate, which can indicate its better thermal stability. Values of residual stresses in coatings calculated by sin2ψ method before and after annealing on the basis of tests performed using X-Ray diffraction, agree with results of dilatometric tests.